Advertisement
Quick Links
The Ultimate in Fall Protection
x1
141 kg/
310 lbs
6
USER INSTRUCTIONS
CE TYPE TEST
CE
PRODUCTION
QUALITY
CONTROL
7
A
B
C
D
E
F
1
Flexible Cable Ladder Safety Systems
BSI (0086)
Kitemark Court
Davy Ave, Knowlhill
I S O
Milton Keynes
9 0 0 1
MK5 8PP, UK
4
BSI (0086)
Kitemark Court
Davy Ave, Knowlhill
Milton Keynes
MK5 8PP, UK
5
1
H
G
LAD-SAF
™
3
ANSI A14.3
prEN 353-1:2012
CSA Z259.2.5
2
Advertisement
Related Manuals for DBI SALA LAD-SAF
Summary of Contents for DBI SALA LAD-SAF
- Page 1 LAD-SAF ™ USER INSTRUCTIONS Flexible Cable Ladder Safety Systems The Ultimate in Fall Protection BSI (0086) Kitemark Court Davy Ave, Knowlhill CE TYPE TEST I S O Milton Keynes ANSI A14.3 9 0 0 1 MK5 8PP, UK prEN 353-1:2012...
- Page 2 K, L...
- Page 3 MODEL NO. 6160030 XXXXXXX SERIAL NO. MODEL NO. 6160047 XXXXXXX SERIAL NO. SERIAL NO. XXXXXXX MODEL NO. ANSI A14.3-2008 ANSI A14.3-2008 6160037 Z259.2.5 PATENT PENDING PATENT PENDING 9508009 Rev. D 9509524 Rev. A...
- Page 4 9" MAX (23cm)
- Page 5 Repairs must be conducted by authorized service providers ONLY. • This equipment is intended to be used as part of a complete Lad-Saf™ Ladder Safety System. Alterations, substitutions, and misuse of this equipment, or failure to follow instructions, may result in serious injury or death.
-
Page 6: System Requirements
X2 Detachable Cable Sleeve must be directly connected to an approved full body harness ™ with the attached carabiner or snap hook (Figure 2, J or N). Do not use connection devices other than the carabiner or snap hook that is part of the Lad-Saf X2 Detachable Cable Sleeve. ™... - Page 7 7 ft. (2 m) of ascent or last 7 ft. (2 m) of descent. Use proper climbing procedures (e.g., maintain 3 points of contact with hands and feet) when ascending or descending any portion of the ladder unprotected by the Lad-Saf system.
- Page 8 Inspect cam (item L) by positioning the sleeve horizontally with the handle/energy absorber (item D) in the upright position and placing the sleeve on the back side on a flat surface with the Lad-Saf X2 label facing up. The cam should rotate fully upwards to the top of the sleeve.
- Page 9 Check for loose or missing fasteners that secure top bracket to structure (bolts, clamp plates, U bolts). If fasteners are loose, re-tighten as necessary to the torque levels listed in the Installation Instructions supplied with your Lad-Saf Flexible Cable Ladder Safety System.
-
Page 10: Specifications
7.0 SPECIFICATIONS 7.1 All top and bottom brackets, cable guides, carrier cable, and fasteners are made of galvanized or stainless steel. Contact DBI-SALA for material specification details if required. The Lad-Saf system, when installed according to the user ™ instructions, meets OSHA, ANSI (A14.3), CSA (Z259.2.5) and CE (prEN 353-1:2012) requirements. - Page 11 INSPECTION AND MAINTENANCE LOG, LAD-SAF™ SYSTEM SERIAL NUMBER: DATE PURCHASED: DATE OF FIRST USE: INSPECTION DATE INSPECTION ITEMS CORRECTIVE ACTION MAINTENANCE NOTED PERFORMED Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By: Approved By:...
- Page 12 INSPECTION AND MAINTENANCE LOG, LAD-SAF™ X2 DETACHABLE CABLE SLEEVE SERIAL NUMBER: MODEL NUMBER: DATE PURCHASED: DATE OF FIRST USE: INSPECTION DATE INSPECTION ITEMS CORRECTIVE ACTION MAINTENANCE NOTED PERFORMED Approved By: Approved By: Approved By: Approved By: Approved By: Approved By:...
Need help?
Do you have a question about the LAD-SAF and is the answer not in the manual?
Questions and answers