Control Panel; Operation; Remote Control - Arlec PA0802GB Instruction Manual

CONTROL PANEL

1 Timer Button
1 2
2
Fan Speed Button
3
Increment Button
(Timer/ Temperature)
4
Decrement Button
(Timer/ Temperature)
5
Mode Selection Button
6
Power ON/OFF Button

OPERATION

Please Note: The beep sound will be heard every time when the button is pressed on keypad display
or remote handset.
POWER ON/OFF BUTTON
To power the unit, ensure that the power plug is plugged into an appropriate 240V a.c receptacle and switch
power on at the wall outlet.
Once the power is applied the unit will beep and the display will come up indicating the temperature of the
room, the unit will be in standby mode.
Press the Power ON button and the unit will start operating in the last selected settings.
IMPORTANT! To prolong the life of the compressor, wait for at least 3 minutes before turning on the
unit, after it has been switched off.
Never turn the air conditioner off by unplugging from the mains wall outlet. Always use the POWER ON/OFF
button to turn off the unit and then wait for few minutes before unplugging the mains power cord.
MODE SELECTION BUTTON
COOL MODE
• Press the MODE button on the control panel or remote
the COOL mode icon lights on the display. This indicates the unit is set in cool mode.
• Press the UP/DOWN button on the control panel or remote
desired between 16°C to 31°C (60.8 to 87.8°F). The temperature will increase/decrease by 1°C each
time UP/DOWN button is pressed.
• Press the FAN speed button on control panel or remote
and the speed indicator will change on the display panel to the selected fan speed as F1 (Low Speed)
and F2 (High Speed).
FAN MODE
• Press the MODE button repeatedly on control panel or remote
next to the FAN mode icon lights up on the display.
• Press the FAN button to change the fan speed from LOW to HIGH and the speed indicator will change
on the display panel to the selected fan speed settings as shown below.
Corresponding will be shown on the display.
F1 for Low speed
F2 for High speed
DRY MODE
• Press the MODE button repeatedly on the control panel or remote
the DRY icon lights on the display. The "dh " marks also appears on the display.
• In DRY mode fan speed is pre-set. Speed button is not available. The temperature cannot be set either.
• Dry mode cannot be used to cool the room, it is ideal to reduce room humidity.
* See water drainage section to drain the condensate (water) in the unit.
SLEEP MODE
• Press the SLEEP mode button on the remote
The operation of the unit is quiet and the unit operates on minimum power.
Note: The sleep mode won't operate if the unit is operating in dry (dehumidifying) or fan mode.
GBIN004060
3 4 5 6
repeatedly until the green LED light next to
/ to set the room temperature as
to change the fan speed from LOW to HIGH
until the green LED light
until the green LED light next to
to turn ON the sleep mode.
6
TIMER BUTTON
Timer function is used to set the ON or OFF time of the unit. This function can be set using the control panel
or remote. The duration of timer is from 1Hrs to 24 Hrs, the timer is incremented in steps of 1Hr every time.
TIMER ON
This function is used to start the unit after a specific time interval.
To set the ON Time:
• To start, ensure the unit is connected to mains supply and the supply switch is turned ON.
• Press the TIMER button on the control panel or remote
to the timer icon will glow. Also, the timer count will be display on the display screen.
• Set the time (between 1Hrs to 24Hrs) after which you want the unit to be turned ON using the
UP/DOWN button
/ on the remote or control panel.
• Once the time is selected, the corresponding time will blink for 5 times on the display and the count
is stored in the memory.
• The unit will start operating once the pre-set time is elapsed.
• To cancel the timer setting, press the TIMER button
and by using UP/DOWN button / bring back the timer count back to "0".
TIMER OFF
This function is used to turn OFF the unit after a specific time interval.
To set the OFF time:
• To turn-off the operating unit after certain duration of time interval press the TIMER button on the
control panel or remote .
• Set the time after which you want the unit to be turned OFF using the UP/DOWN button
on control panel or remote.
• Set the time (between 1Hrs to 24Hrs) after which you want the unit to be turned OFF using the
UP/DOWN button
/ on the remote or control panel.
• Once the time is selected, the corresponding time will blink for 5 times on the display and the count
is stored in the memory.
• The unit will be turned OFF when the pre-set time is reached and will be in standby mode.
• To cancel the timer setting, press the TIMER button
and by using UP/DOWN button / bring back the timer count back to "0".
Note: In an event of power failure the timer needs to the reprogrammed.

REMOTE CONTROL

2
1
Fan Speed Button
2 Increment Button
(Timer/ Temperature)
1
3 Mode Selection Button
4
4 Sleep Mode Button
5
Decrement Button
5
(Timer/ Temperature)
6
Timer Button
7 Power ON/OFF Button
GBIN004060
and the corresponding green light next
again on the control panel or remote
/
again on the control panel or remote
• The remote-control unit requires
2 x 1.5V AAA Alkaline batteries.
• You can use the remote control when the
3
distance between the air conditioner and the
remote is less than five meters. Make sure
6 the deviation of the remote is less than 30°.
• The remote control has all the same
7
functions as the buttons on the control
panel of the air conditioner except the
remote control has one extra/additional
function (SLEEP MODE ) as compared
to control panel.
• To use the remote control, make sure that
the unit is plugged into the mains supply,
then point the remote control to the sensor
located at the control panel and press the
desired button.
• The remote control operating range is
5 metres. Make sure there are no obstacles
between the remote and the sensor.
7