HIKVISION DS-2CE16H0T-ITF User Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Security Camera
  5. DS-2CE16H0T-ITF
  6. User manual

HIKVISION DS-2CE16H0T-ITF User Manual

Turbo hd h0t series bullet & dome camera
Hide thumbs Also See for DS-2CE16H0T-ITF:

Advertisement

Table of Contents

TURBO HD
H0T Series Bullet & Dome
Camera

User Manual

User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:
Type
Type I Camera
Type II Camera
Type III Camera
This manual may contain several technical incorrect
places or printing errors, and the content is subject to
change without notice. The updates will be added to
the new version of this manual. We will readily improve
or update the products or procedures described in the
manual.
Model
DS-2CE16H0T-ITF
DS-2CE16H0T-ITPF
DS-2CE16H0T-IT1F
DS-2CE16H0T-IT3F
DS-2CE16H0T-IT5F
DS-2CE56H0T-VPITF
0100001071116

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DS-2CE16H0T-ITF and is the answer not in the manual?

Questions and answers

Related Manuals for HIKVISION DS-2CE16H0T-ITF

Summary of Contents for HIKVISION DS-2CE16H0T-ITF

  • Page 1: User Manual

    Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer. This manual applies to the models below: Type Model DS-2CE16H0T-ITF Type I Camera DS-2CE16H0T-ITPF DS-2CE16H0T-IT1F Type II Camera DS-2CE16H0T-IT3F DS-2CE16H0T-IT5F...

  • Page 2: Regulatory Information

    Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
  • Page 3 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected.

  • Page 4: Product Features

    Keep the camera away from liquid while in use for  non-water-proof device. While in delivery, the camera shall be packed in its  original packing, or packing of the same texture. Mark Description Table 0-1 Mark Description Mark Description DC Voltage 1 Introduction 1.1 Product Features...

  • Page 5: Installation

    1.2.3 Overview of Type III Camera Power Cord 12 VDC Video Cable Mounting Base Switch Button Pan Adjusting Screw IR LED Tilt Adjusting Screw Photoresistor Black Liner Bubble Safty Rope Figure 1-3 Overview of Type III Camera Note: Press and hold the switch button for 5 seconds to switch the video output.
  • Page 6 Note: Drill the cable hole, when adopting the ceiling outlet to route the cable. 3. Attach the bracket to the ceiling/wall and secure the camera with supplied screws. Figure 2-2 Fix the Camera to the Ceiling Note: The supplied screw package contains self-tapping ...
  • Page 7 Figure 2-4 Drill Template of Junction Box 3. Take apart the junction box, and align the screw holes of the bullet camera with those on the Junction box’ cover. 4. Fix the camera on the junction box’s cover with supplied screws. Junction Box Cover Figure 2-5 Fix the Camera on the Junction Box’s Cover...
  • Page 8 2.2 Installation of Type II Camera 2.2.1 Ceiling/Wall Mounting without Junction Box Steps: 1. Paste the drill template (supplied) to the place where you want to install the camera. 2. Drill the screw holes according to the drill template, and the cable hole (optional) on the ceiling. Screw Hole Figure 2-8 Drill Template...
  • Page 9 Ceiling/Wall Mounting with Junction Box 2.2.2 Before you start: You need to purchase a junction box separately. Steps: 1. Paste the drill template on the ceiling/wall. 2. Drill screw holes and the cable hole (optional) in the ceiling/wall according to the holes of the drill template.

  • Page 10: Adjusting Screw

    Screw Hole Cable Hole Drill Template Hole A: for cables routed through the ceiling screw hole 1: for Mounting Base Figure 2-14 Drill Template Note: Cable hole is required, when adopting the ceiling outlet to route cables. 3. Loosen the set screws with a hex wrench (supplied) to remove the bubble.

  • Page 11: Menu Description

    2). Hold the black liner to adjust the pan position [0° to 355°]. 3). Hold the camera body to adjust the rotation position [0° to 355°]. 8. Reinstall the bubble, and tighten the screws. Figure 2-18 Bubble Reinstallation 3 Menu Description Purpose: Call the menu by clicking button on the PTZ Control...

  • Page 12: Main Menu

    VIDEO FORMAT LANGUAGE EXPOSURE MODE BACK EXPOSURE EXIT SAVE & EXIT AUTO COLOR DAY/NIGHT BACK EXIT SAVE & EXIT WHITE BALANCE MAIN MENU BRIGHTNESS CONTRAST SHARPNESS VIDEO SETTINGS SATURATION MIRROR BACK EXIT SAVE & EXIT FACTORY DEFAULT EXIT SAVE & EXIT Figure 3-2 Main Menu Overview 5.
  • Page 13 Figure 3-3 EXPOSURE EXPOSURE MODE You can set the EXPOSURE MODE as GLOBAL, BLC, and DWDR. GLOBAL  GLOBAL refers to the normal exposure mode which performs exposure according to the whole image brightness. BLC (Backlight Compensation)  BLC (Backlight Compensation) compensates light for the front object to make it clear, but this may cause the over-exposure of the background, where the light is strong.

  • Page 14: Video Settings

    IR LIGHT  You can turn on/off the IR LIGHT to meet the requirements of different circumstances. SMART IR  The Smart IR function is used to adjust the light to its most suitable intensity, and prevent the image from over exposure.

  • Page 15: White Balance

    VIDEO SETTINGS  WHITE BALANCE BRIGHTNESS CONTRAST SHARPNESS SATURATION MIRROR  BACK  EXIT  SAVE & EXIT Figure 3-6 VIDEO SETTINGS WHITE BALANCE White balance, the white rendition function of the camera, is to adjust the color temperature according to the environment.

  • Page 16: Factory Default

    H: The image flips 180° horizontally. V: The image flips 180° vertically. HV: The image flips 180° both horizontally and vertically. 3.6 FACTORY DEFAULT Move the cursor to FACTORY DEFAULT and click Iris+ to reset all the settings to the factory default. 3.7 EXIT Move the cursor to EXIT and click Iris+ to exit the menu without saving.

This manual is also suitable for:

Ds-2ce16h0t-it1fDs-2ce16h0t-itpfDs-2ce16h0t-it3fDs-2ce16h0t-it5fDs-2ce56h0t-vpitf

Table of Contents