Advertisement
Advertisement
Table of Contents
Related Manuals for Savant CLI-W200
Summary of Contents for Savant CLI-W200
- Page 1 SMART THERMOSTAT QUICK START GUIDE CLI-W200 009-1593-02...
-
Page 2: What's In The Box
What’s in the Box (1) Wi-Fi Thermostat (CLI-W200x) (1) Installation Kit (2) Drywall Anchors (039-0328-xx) (2) #6 x 3/4 inch Pan Head Screws (039-0327-xx) (1) Sheet of Wire Labels (080-0096-xx) (1) Quick Start Guide (this document) Specifications Environmental Temperature 32 to 104 F (0 TO 40 C) Humidity 10% to 90% (non-condensing) Standards... -
Page 3: Getting Started
Welcome This document describes how to: 1. Remove the old thermostat. 2. Mount your new CLI-W200 thermostat. 3. Wire your new CLI-W200 thermostat. Getting Started The following is needed for a trouble free installation: – Pencil – #2 Phillips screwdriver –... -
Page 4: Remove Old Thermostat
Color of Wire NOTE: Additional information on terminal designa- tions and useful wiring diagrams are available in the CLI-W200 Thermostat Deployment Guide located in the pages of the Savant Customer Community. 7. With a screwdriver, remove the wires from each terminal. - Page 5 Install Thermostat Mounting Plate Pull wires through the center opening Bubble level slot (Landscape) Bubble level slot (Portrait) 1. To separate the thermostat from its mounting plate, grasp the mounting plate in one hand and the thermostat in the other (Grasp the end opposite the proximity sensor). 2.
-
Page 6: Making Connections
Tug on each wire a bit to verify they are secure. Connecting Power The CLI-W200 does not run on batteries and requires a separate power source to operate. To power the thermostat, a voltage must be applied to the RH and 24C terminals. - Page 7 Additional Powering Schemes If the HVAC system uses separate power sources to run the heating and cooling, you should have three wires labeled for power (R, C, and RC). In this scenario, remove the jumper shunt from JP1. The next section describes this. Jumper Shunt - JP1 Jumper JP1 on the thermostat board connects the RH and RC terminals.
-
Page 8: Temperature Sensors
HVAC Wiring Use the table below to connect the signaling wires from the HVAC system. Depending on the type of system installed in your home will determine which wires are connected. In some installations, only the power wires described in the previous sections are required. -
Page 9: Additional Information
Network and Configuration Requirements With the thermostat installed and wired, it can now be added to the local network and once communicating with the Savant Pro System Host an HVAC configuration can be created and uploaded to the Host. Locate the CLI-W200 Thermostat De- ployment Guide available on the Savant Customer Communi- ty to finish installation of the thermostat. -
Page 10: Frequently Asked Questions
Frequently Asked Questions Does the CLI-W200 require batteries? No, the CLI-W200 is powered using the power from the HVAC system. If no common (C) wire was removed from the old thermostat, a common wire must be added. How does CLI-W200 get software updates? Software is updated Over The Air (OTA). - Page 11 FCC and IC Identifier for Savant Thermostat This device electronically displays the FCC declaration of conformity logo as well as the FCC and IC identifier. This information can be found on the device...
- Page 12 20 cm de distance entre la source de rayonne- ment et votre corps. Identificateur de la FCC et d’IC pour Savant Thermostat Ce périphérique par voie électronique affiche le logo de déclaration de confor- mité...
Need help?
Do you have a question about the CLI-W200 and is the answer not in the manual?
Questions and answers