Page 1
User's Manual AERO-20A / AERO-20.120A Antes de utilizar el equipo, lea la sección “Precauciones de seguridad” de este manual. Conserve este manual para futuras consultas. Before operating the device, please read the “Safety precautions” section of this manual. Retain this manual for future reference.
Precauciones de Seguridad Safety Precautions Cajas acústicas activas / Self-powered loudspeaker enclosures El signo de exclamación dentro de un triángulo indica la The exclamation point inside an equilateral triangle is intended to existencia importantes instrucciones operación alert the users to the presence of important operating and mantenimiento en la documentación que acompaña al producto.
GARANTÍA Todos nuestros productos están garantizados por un periodo de 24 meses desde la fecha de compra. Las garantías sólo serán válidas si son por un defecto de fabricación y en ningún caso por un uso incorrecto del producto. reparaciones garantía pueden realizadas,...
DECLARATION OF CONFORMITY DAS Audio Group, S.L. C/ Islas Baleares, 24 - 46988 - Pol. Fuente del Jarro - Valencia. España (Spain). Declara que AERO-20A: Declares that AERO-20A: Cumple con los objetivos esenciales de las Directivas: Abide by essential objectives relating Directives: de Baja Tensión (Low Voltage Directive)
- New rigging system for improved ease of use and safety. Power for the AERO-20A is provided by a package of integrated electronics that includes a new 1200 W (2400 Wpeak) amplifier, advanced digital signal processing and connectivity for remote system management.
AMPLIFIER Description The amplifier is common for both models. 1) INPUT : XLR-type input signal connector. This is balanced connector just like the LOOP THRU connector with the following pin assignments: 1 =GND (ground). 2 =(+) Non inverted input. 3 =(-) Inverted input. 2) LOOP THRU : XLR-type output connector for connecting several units together and sending them all the same signal.
ON / OFF Normally it is enough just to let the unit cool A sound system should be switched on down after you have corrected the problem so that sequentially. Switch on the self-powered units last the system functions properly again. in your sound system (switch on the subwoofer The amplifier is provided with a radiator made before the mid-high system).
Troubleshooting PROBLEM CAUSE SOLUTION sound from unit. 1 – The signal source is sending no 1 – Check that the mixer or sound SIGNAL LED does not light up. signal. source is sending signal to the UNIT. 2 – Defective cable. 2 –...
CHANGE OF CONFIGURATION (reset) The unit allows to change some default factory settings using the controls in the amplifier´s panel. The firmware which is described here is the 1.20 version. However, gain and delay only can be changed with DASnet . To re-establish the default factory settings (Number of units/Throw/gain/delay...) without using DASnet the system has to be switched ON while pressing the Throw button.
Warning Due to the numerous images needed to When a system is flying, the working load must explain the AERO-20A array system setup, this be lower than the resistance of each individual manual can´t offer all the necessary information to flying point in the enclosure, as well as each box.
Page 15
Next, we name the accessories with images. Consult the Rigging Manual for more information about the accessories. PICKUP-AX-AE20 AX-COMBO2040 PL-20S AXS-AE20 AX-AE20 Other accessories DASnet rack 26-230V DASnet rack 26-115V (2 patch panel + power distro 32Amp) (2 patch panel + power distro 30Amp) (European version) (American version) PUSH...
ANNEX I: Line connections: unbalanced and balanced There are two basic ways to transport an audio signal with microphone or line level: Unbalanced line: Utilising a two conductor cable, it transports the signal as the voltage between them. Electromagnetic interference can get added to the signal as undesired noise. Connectors that carry unbalanced signals have two pins, such as RCA (Phono) and ¼”...
Page 17
ANNEX II : DASnet cables With each system, cabling and patch panels are provided. It is very important to use the system with the intended cables to prevent electromagnetic interferences between the analog audio signal, the DASnet data and the power. Be sure to check the specifications provided by the cable manufacturer.
Page 18
www.dasaudio.com DAS Audio Group, S.L. DAS Audio of America, INC. DAS Audio Asia PTE. LTD. DAS do Brasil LTDA. C/. Islas Baleares, 24 6900 NW 52th Street 3 Temasek Avenue, Centennial Rua Dos Andradas, 382 SL 46988 Fuente del Jarro Miami, FL.
Need help?
Do you have a question about the AERO-20A and is the answer not in the manual?
Questions and answers