Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Genway C5-IP-OS-02
Summary of Contents for Genway C5-IP-OS-02
- Page 1 User Manual Outdoor Station...
-
Page 3: Table Of Contents
Contents Unit 1 Overview ......................1 1.1 Functions and Characteristics ................1 1.2 Parameters ......................1 Unit 2 Appearance and Interface ..................2 2.1 Front View ......................2 2.2 Rear View ......................2 Unit 3 Installation ......................4 3.1 Height Installation .................... 4 3.2 Installation Illustration .................. -
Page 4: Unit 1 Overview
Unit 1 Overview Outdoor station is one of the main parts in the digital video door phone system. It is connected with indoor stations, guard units and other devices in the system by standard CAT5 cables. And it supports RFID access control (IC or ID). 1.1 Functions and Characteristics ... -
Page 5: Unit 2 Appearance And Interface
Unit 2 Appearance and Interface 2.1 Front View Carema Angle Adjustment Display Area Card Reading Area Keypad Area Wring Area Speaker... -
Page 6: Rear View
2.2 Rear View 1. Network Interface (Non-standard PoE 24V power supply; if power is needed for gate lock or low temperature heating function is required, outdoor station must be supplied independently).) 2. Interface for input power:DC 24 V (interface for independent power supply) 3. -
Page 7: Unit 3 Installation
Unit 3 Installation 3.1 Height Installation Ground Notes for Installation : 1. The depth of the groove should be well measured. Too much space between the wall and the embedded is prohibited. 2. Do not install on the wall that have much contact with rain, moisture or dust. -
Page 8: Installation Illustration
3.2 Installation Illustration Step 1: Put the embedded box into the preformed groove. After getting the cable out through the opening, fasten the box Embedded box Preformed with nails or by cement. groove Embedded box dimension（W/H/D）: 131.6 x 340x 49mm Opening for cable Snap Wall... -
Page 9: Unit 4 Operation Instructions
Unit 4 Operation Instructions 4.1 Call Indoor Station Visitors make a call via inputing building number、unit number and room number, then press # to start the call. There will be ring back tones on this station, during ringing, press * to cancel the call . If there is no any answer within 30 seconds, call will be ended automatically . -
Page 10: Unit 5 Entry Settings
Unit 5 Entry Settings 5.1 Standby Interface Home 5.2 Login for Engineering Settings Press "#" and then "*" key, enter into the login interface for engineering settings. Default password is "801801" Login for Engineering Settings. -
Page 11: Setting Interface
5.3 Setting interface Input the correct password then press "#" key to confirm and enter it. You can both press the up/down key to choose the item of setting, or press the corresponding number (shown on the icon) directly. Engineering Settings... -
Page 12: Unit 6 System Settings
Unit 6 System Settings System settings, including time setting, sound setting, language setting, password setting, unlocked- time setting, card management, and elevator setting. You can both press the up/down key to choose the item of setting, or press the corresponding number (shown on the icon) directly. -
Page 13: Sound Setting
6.2 Sound Setting Use the up/down key or number keys to select the item, and "#" key to adjust. After adjusting finished, press "*" key and it will save and return. Sound Setting 6.3 Language Setting Use the up/down key or number keys to choose the language, press "#" key to confirm. -
Page 14: Password Setting
6.4 Password Setting Password setting includes 3 items: On and Off for user password and public password, and change of public password. Password Setting 6.5 Unlocked-Time Setting Unlocked-time setting is to set the duration of the unlocked time after door opened. When the time is out, the door will lock again automatically. -
Page 15: Card Management
6.6 Card Management Card management includes registration, check(card information), delete, clear(delete all) and copy. Card Management Enter “register” and register by a card or by inputting the card number. Press "#" key to confirm. You can press "*" key to delete if needed. Remark：... - Page 16 The operation of “delete” is same as “registration”. Enter “check” and you can check all card numbers and the quantity of cards registered. Card Information If you choose the “clear”, a message will come out for you to confirm the operation(delete all).
-
Page 17: Unit 7 Configuration Settings
Unit 7 Configuration Settings Configuration settings includes device property, dialing setting, alarm setting, factory test, configuration password, company info, device info. Use up/down key to choose or directly press corresponding number to a particular setting. Configuration Settings 7.1 Device property The device can either be used as outdoor station or gate station, depending on the definition of device property. - Page 18 If it is a outdoor station, you will find there are setting for building number( 1-99), unit number (1-9) and entrance number of the building (1-10) Outdoor Station Number Setting If it is a gate station, you only need to input the number of the gate( 1-32). Gate Station Number Setting...
-
Page 19: Dailing Settings
7.2 Dailing Settings If it is outdoor station, there will be options: “3” or “4”. If you choose “3”, you should dial 3 numbers (3digit)to call. For example, to call room 8 floor 8, you should dial 808. If you choose “4”, you should dial 4 (4digit) numbers to call. For example, to call room 8 floor 8, you should dial 0808. - Page 20 Bld.&Unit Floor &Room building digit building digit building number + 1 digit number + 1 digit number + 1 digit unit + 1 digit floor unit + 1 digit floor unit + 1 digit floor digit room digit room digit room number number...
-
Page 21: Alarm Setting
7.3 Alarm Setting Enter the alarm setting and choose “on” or “off” for each items. When the alarm is triggered, it will send information to management center/guard unit. Alarm Setting Besides 6 test items, factory test has also the function of restart and factory reset. Choose restart and confirm, the system will restart. -
Page 23: Configuration Password
7.4 Configuration Password The default configuration password is 801801. And here you can change the password. Input the current password. The text frame will move to new password if the password you input is correct. Then Input your new password(6 digit) twice. Engineering Password Setting “device information”...
Need help?
Do you have a question about the C5-IP-OS-02 and is the answer not in the manual?
Questions and answers