Components identified by on schematics and parts leads are not pinched or that hardware is not lists must be sealed by a soldering iron after lodged between the chassis and other metal parts in replacement and adjustment. the monitor. AQ17KS...
“anti-static” a carpeted floor can generate enough static can generate electrical charges sufficient to damage electricity to damage an ESD. ESDs. Indicates ESDs on the Schematic Diagram in this manual. AQ17KS...
Pin No. GND-R Green Blue H/V Sync Sense 0 DDC Return Green GND-R GND-G GND-G Sense 1 GND-B Reserved Blue GND-Sync/Self-raster Sense 2 DDC Data V-Sync H-Sync GND-B V-Sync DDC Clock H-Sync Figure 2-1. Male Type Figure 2-2. Male Type AQ17KS...
B : Horizontal sync width O : Frame time total P : Vertical sync width C : Back porch D : Active time Q : Back porch R : Active time E : Front porch S : Front porch AQ17KS...
3 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the AQ17KS monitors. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 3-1 Disassembly Cautions:1. Disconnect the monitor from the power source before disassembly.
Page 10
Shield. Front Cover is broken, secure the 7. Place the Video PCB on a flat, level surface cabinet by applying a 4x16 screw in that is protected from static electricity. the extra holes on each side of the cabinet. AQ17KS...
Page 11
7. Carefully lift the Main PCB Ass’y and remove the remaining ground wires. 8. Place the Main PCB Ass’y on a flat, level surface that is protected from static electricity. 3-2 Reassembly Reassembly procedures are in the reverse order of Disassembly procedures. AQ17KS...
Page 12
3 Disassembly and Reassembly Memo AQ17KS...
4-1-1 (e) SCANNING FREQUENCY Horizontal : 30 kHz to 70 kHz (Automatic) Vertical : 50 Hz to 160 Hz (Automatic) Unless otherwise specified, adjust at the 1024 x 768 mode (68 kHz/85 Hz), Refer to Table 2-1 on page 2-3. AQ17KS...
Page 14
CONNECTOR the use of an additional signal generator. MONITOR INTERFACE BOARD VER. 2.0 SIGNAL CABLE Figure 4-2. Setup 2, Without Signal Generator 5V DC ADAPTOR 3-WIRE CABLE PARALLEL CABLE SIGNAL GENERATOR Figure 4-1. Setup 1, With Signal Generator AQ17KS...
Page 15
4-2-3 CENTER RASTER (68kHz/85Hz). Adjust SW401 so that the back raster comes to the center when you apply basic mode for 17”. 4-2-4 (b) VERTICAL SIZE ADJUSTMENT CONDITIONS Scanning frequency: 68 kHz/85 Hz Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum AQ17KS...
Page 16
(5 %) Horizontal: 20.5~23.5 Horizontal: Less than 1.10 mm 4 : 3 Vertical : 20.5~23.5 Vertical : Less than 1.10 mm Horizontal: 19.18~22.07 Horizontal: Less than 1.03 mm 5 : 4 Vertical : 20.5~23.5 Vertical : Less than 1.10 mm AQ17KS...
Page 17
4-2-12 To Delete the User Mode Data To delete the adjustment data from the user modes, click “@4: USER DELETE” in right ment. 4-2-13 Save the Data To save the adjustment data for a mode, press “@3: ALL MODE SAVE” in right ment. AQ17KS...
0.298 ± 0.02. 4. Use control bar after selecting “RED CUTOFF” in left menu to 0.283 ± 0.02. * If color values would not be matched desirable values, repeat sequence 3 and 4 after readjusting “GREEN CUTOFF” control a little different. AQ17KS...
Page 19
7.5:10. Note: Color purity adjustments should only be CONDITIONS attempted by qualified personnel. Scanning frequency: 68 kHz/85 Hz (1024 x 768) Display image: White flat field Brightness: Cut off point at 24 ft-L Contrast: Maximum AQ17KS...
Page 20
= 0.142 ± 0.015 y = 0.066 ± 0.015 (For 9300K color adjustment: x = 0.283 ± 0.02, y = 0.298 ± 0.02) 6. When you have the PCMs properly adjusted, carefully glue them together to prevent their movement during shipping. AQ17KS...
CH1 P-P = 100 V CH1 RMS = 350.2 V Check and replace D614, IC601, IC601 Pin 1 waveform is right? Q602, and ZD601. Check and replace IC201, IC301, C622 Voltage is 13 V ± 0.5V? IC401, Q402, and Q404. Operate normally? Replace Main board. Verify voltages. Done. AQ17KS...
Page 22
CH1 P-P = 100V CH1 RMS = 325.8 V Check IC201 Pin 40. +12 V line off? Check IC201 Pin 6. IC602 Pin 4 Check IC201 Pin 6. voltage exists? Check and replace IC602. IC601 Pin 1 output Refer to 5-1-1 No Power Supply. voltage exists? Done AQ17KS...
Page 23
Check S1 ~ S4 signal. S1~S4 signals are right at each CH1 P-P = 20.0 V CH1 RMS = 46.80V Check and replace IC201. frequency block? Check and replace Q404, Q409, Q410, Q411, Q414, Q415, Q416, Q420, and Q421. AQ17KS...
Page 24
B+ offset Check and replace IC201. 200 V (Q404, Collector) DAC values? Q404 Collector waveform is Check and replace Q405, right? Q406, Q407, and Q408. CH1 P-P = 200V CH1 RMS = 387.2V Check some parts around D409 and L401. AQ17KS...
Page 25
5-1-10 Tilt Failure Check tilt connector connection IC201 Pin 20 output duty varies Check and replace IC201. with different DAC values? IC603 Pin 13 output varies with Check and replace IC603. different DAC values? Check and replace Q301 and Q302. AQ17KS...
Page 26
Check DY connector connection. CH1 P-P = 10.0 V CH1 RMS = 5.06 V 5-1-12 V Size or Position Variation Failure IC401 Pin 12 output varies with Check and replace IC201 and IC401. different DAC values? Check and replace IC301. AQ17KS...
Page 27
CH1 P-P = 50.0 V CH1 RMS = 73.7V Check and replace IC101. varies with different patterns? Check CN102. T501 Pin 8 output exists? Check and replace T501. IC201 Pin 26 output exists and Check and replace IC201. varies with different patterns? Done AQ17KS...
Page 28
T502 Pin 1 output is right? Replace the T502. CH1 P-P = 50.0V CH1 RMS = 75.6V Check the connection between FBT 100 V (T502, #1) Focus pin and CRT Socket PCB. CH1 P-P = 100V CH1 RMS = 124.0V AQ17KS...
Page 29
Cathode DC levels are right? Check and replace QR01, QR02, QG01, QG02, QB01, and QB02. 20.0V (IC103, #1, 2, 3) Check G2 wire, CRT Socket board G2 voltage is right? and FBT. CH1 P-P = 20.0V CH1 RMS = 40.52V Change CRT. Done. AQ17KS...
Page 30
IC201 Pin 13 and 14 inputs Check C202, C203 and X201. are right? CH1 P-P = 1.00 V CH1 RMS = 2.108V IC201 Pin 18 input is right? Check IC605. All in/output values are right? Replace IC201. Done 5-10 AQ17KS...
Page 31
CH1 P-P = 1.00V CH1 RMS = 5.024V IC101 Pin 18, 21 and 24 Check and replace IC101. outputs are right? 1.00 V (IC101, #18,21,24) Check and replace IC103. CH1 P-P = 1.00V CH1 RMS = 2.580V Done AQ17KS 5-11...
Page 32
S/W? Check IC201. 5-1-20 Degaussing Failure Check degaussing connector. RL601 operation is right? Check D-coil and TH601. Q601 base input is right? Check and replace Q601. IC201 Pin 4 output is right? Check and replace IC201. Done 5-12 AQ17KS...
Check G2 voltage, high voltage and R, G, B cathode voltage. 5-2-2 Shut Down Blinking LED’s? Check power supply. Check horizontal, vertical deflection Scan failure? system and check power supply secondary voltages. Video failure? Check Video board. Check and replace IC201. Done AQ17KS 5-13...
Page 34
Check QR01, QR02, QG01,. QG02, on all cathodes? QB01, and QB02. G2 voltage is right? Check Q501 and D520. Heater voltage is right? Check D608, Q604 and T601. G1 voltage is right? Check D504, Q502 and T501. Replace CRT. Done 5-14 AQ17KS...
Page 35
CH1 P-P = 5.00V CH1 RMS = 28.33V 20.00V (CRT Socket, G1) V_FLB pulse is on Check Q303. Collector of Q303? Does approve the Vertical pulse Check CN102 and CN201. CH1 P-P = 20.0V CH1 RMS = 66.68V on the CRT Socket G1? Done AQ17KS 5-15...
Page 36
3 of CN202. Signals are right? Check Video Cable Signals at Pin 28 and 29 of Check IC201. IC201 are right? Signals at Pin 14 and 15 of Check IC401 IC401 are right? Check circuits on Main board. Done 5-16 AQ17KS...
Page 37
5 Troubleshooting 5-2-6 Misconvergence Try readjusting convergence. The convergence is now Done within spec.? Readjust convergence. The convergence is now Done within spec.? Change CRT and readjust convergence. Done AQ17KS 5-17...
Page 38
Refer to 5-1-15 Dynamic Dynamic focus circuit is right? Focus Failure. Replace the CRT and verify focus. 5-2-8 Purity Failure Degaussing Purity is right? Done Degaussing circuit is right? Refer to 5-1-20 Degaussing Failure. Replace CRT and verify purity. 5-18 AQ17KS...
H– V– (BROWN)V- CN201 CN102 70 V 70 V 6.3 V 6.3 V BLANK 12 V 12 V V-SYNC DEGAUSSING COIL V-SYNC CN603 IICDATA IICCLK IICDATA CLAMP IICCLK CLAMP AC INPUT AC INPUT CN601 AC INPUT CN202 CN304 TILT AQ17KS...