Greengate OAC-DT-2000-MV Installation Instructions

General Information
• Read all instructions on both sides of this sheet first • For indoor use only
• Install in accordance with ALL local codes

Specifications

Power Requirements: 277 VAC:
120 to 347 VAC, 50/60 Hz - Neutral Required • Fluorescent/Ballast - 0 to 2700W, 50/60 Hz
120 VAC: 347 VAC:
• Incandescent/Tungsten - 0 to 800W, 50/60 Hz • Fluorescent/Ballast - 0 to 1500W, 50/60 Hz
Operating Environment:
• Fluorescent/Ballast - 0 to 1200W, 50/60 Hz
Motor Load: ¼ HP @ 125 VAC • Temperature: 32° F – 104° F (0° C – 40° C)
230 VAC: • Relative Humidity: up to 90% non-condensing
• Fluorescent/Ballast - 0 to 1200W, 50/60 Hz
Description
The OAC-DT Ceiling Mount Line Voltage Occupancy Sensor is a Passive Infrared (PIR) and Ultrasonic (US) motion
sensing lighting control, used for energy savings and convenience. PIR is used to turn the lights ON and then either
technology is used to keep the lights ON.
The sensor includes self-adaptive technology that continually adjusts to conditions by adjusting sensitivity and time
delay in real-time.
Coverage
20 ft
(6.096m)
16 ft
(4.87 m)
12 ft
(3.65 m)
0
12 ft
(3.65 m)
16 ft
(4.87 m)
20 ft
(6.096m)
8.5 ft
(2.59 m)
3 ft
(0.91)
0
32 ft 23 ft 15 ft 5 ft 0 5 ft 15 ft
10 ft 10 ft
(9.75 m) (7.01 m) (4.57 m) (3 m) (1.52 m) (1.52 m) (4.57 m) (7.01 m)
(3 m)
Dual Technology Ceiling Mounted Line
Voltage Occupancy Sensor

Location

The maximum coverage area may vary somewhat according to room shape and the presence of obstacles. Decrease
total coverage area by 15% for "soft" rooms (for example, heavy draperies or heavy carpeting). The sensor must have
a clear view of the area to be controlled. The sensor will not "see" through glass. Mounting height should not exceed
12 feet. Optimum mounting height is 8 to 10 feet. Mount the sensor so the grills face the open portion of the room and
are not facing a nearby wall, door, window, or other obstructing object. Avoid pointing into hallways. Mounting at fixture
height is most effective. *To prevent false activation, the sensor should be mounted away from the air supply duct a
minimum of 4 to 6 feet.
The OAC-DT sensor can be mounted to a standard 2.125" deep x 4" octagon or 2.125" deep x 4" foursquare
electrical boxes (foursquare box requires a two-gang mud ring).
Minor Motion, IR
Maximum coverage area may
vary somewhat according to room
shape and the presence of obstacles.
Major Motion, IR
Minor Motion, Ultrasonic The NEMA WD 7 Guide and robotic
method were utilized to verify
coverage patterns.
Major Motion, Ultrasonic
23 ft 32 ft
(9.75 m)
Ultrasonic
Activated
30 ft
9.14 m
30 ft
9.14 m
OAC-DT-2000
Installation Instructions
Model # OAC-DT-2000-MV
Model # OAC-DT-2000-DMV

Wiring

CAUTION: Before installing or performing any service on a Greengate system, the power MUST be turned OFF at
the branch circuit breaker. According to NEC 240-83(d), if the branch circuit breaker is used as the main switch
for a fluorescent lighting circuit, the circuit breaker should be marked "SWD". All installations should be in com-
pliance with the National Electric Code and all state and local codes.
NOTE REGARDING COMPACT FLUORESCENT LAMPS: The life of some compact fluorescent lamps (CFLs) is shortened
by frequent automatic or manual switching. Check with CFL and ballast manufacturer to determine the effects of cycling.
1. Make sure power is turned OFF at the branch circuit breaker.
2. Wire units as shown in wiring diagrams per applicable voltage requirements. (Use twist-on wire connectors
for all connections) CAP ALL UNUSED WIRE LEADS.
3. Mount unit to ceiling, junction box, or round fixture with raceway.
4. Turn power back ON at the branch circuit breaker and wait 2 minutes for the unit to stabilize.
5. Make necessary adjustments. (See Checkout and Adjustments section)
One Sensor, One Load
120-347 VAC
Line
Neutral
Black
Blue
White
One Sensor, Two Loads
120-347 VAC
Line
Neutral
Black
White
Blue
Red
Red
Red leads are non-polorarity sensitive.
Load 1
Load 1 Load 2