Cardo Systems Scala Rider G9 Quick Manual

T
his Quick Guide is not a substitute to the user manual and addresses only
a limited scope of features and functions of your scala rider G9. Use it to
look up basic functions and commands while you are on the road without the
user manual.
This Quick Guide can be printed and folded for easy reference while on the
road, or it may be viewed directly on your smartphone or tablet.
| GENERAL FUNCTIONS
1
Power ON / OFF Press
• ON: 3 BLUE flashes + ascending tone
• OFF: 3 RED flashes + decending tone
Volume
Tap or
Mute
Tap and
In Standby, press
Battery level
• Blue LED = Full charge
indicator
• Purple LED = Half charge
• Red LED = Almost empty
Hear Your Buddy
In Standby, tap
Name
In Standby, press
Paired Device
If "One+8" Buddies are within range, purple LEDs flash for
Indication
2 seconds
Group Signal
Tap twice
Enable / Disable
Spoken Status
Press
Announcements
| SETTINGS MENU
2
Enter Menu
Exit Menu
| MAIN UNIT LED INDICATION
3
None
1 BLUE flash every 3 seconds
2 BLUE flashes every 3 seconds
1 RED flash every 3 seconds
2 RED flashes every 3 seconds
Solid RED
| VOICE CONNECT (VOX)
4
Adjust via the Settings Menu, the App or the Cardo Community.
VOX Sensitivity
High: Use this setting if it is difficult to activate VOX
(Default: Medium)
Low: Use this setting if it is too easy to activate VOX
VOX can be set to activate the Voice Command (default) or to
VOX Operation Mode
start an Intercom Call via the Cardo Community or the App
In Standby, press
Enable / Disable VOX
• Enabled: Blue flash for 2 seconds
(For Intercom calls only)
• Disabled: Red flash for 2 seconds
for 2 seconds
to adjust and set volume of current audio source
simultaneously
for 2 seconds
and simultaneously
and for 2 seconds
and for 2 seconds
In Standby, press and for 2 seconds
Press for 2 seconds
scala rider G9 is OFF
Standby mode – No active audio
Active mode – Call in progress / music or other
audio source is ON
Standby mode – Battery is low
Active mode – Battery is low
Charging
and for 2 seconds
scala rider G9 Unit Mobile button (On / Off)
Volume / Forward
Channel A / MP3
Voice Command
| VOICE COMMANDS
5
1. In Standby, tap or speak any word loudly to activate VOX
2. Speak a Voice Command from the table below:
Current Mode Desired Action
"One+8" Intercom Call
Standby / FM / A2DP
/ AUX
Intercom call with A or B
Start A2DP
Standby
Turn on FM
Turn off FM
FM Radio Next Station Preset
Previous Station Preset
Next track
A2DP Music Previous track
Stop / Pause A2DP
| PAIRING BLUETOOTH DEVICES:
6
MOBILE PHONE/GPS/A2DP MUSIC PLAYER
Bluetooth Channel 1 pairing mode
Bluetooth Channel 2 pairing mode
To pair a GPS, when LEDs begin rapidly alternating, tap
| PHONE CALLS
7
Tap
Answer a call
Reject a call Remain silent for 15 seconds, or press
End a call Tap
Voice Dial* (if supported by
Tap
mobile phone)
Redial*
Double-tap
Hot Dial** Double-tap
Set default mobile***
While on a phone call, press
In Standby, press
Change default mobile
INTERCOM CONFERENCE MODE
Add/Remove Channel "A"
Tap
to/from a call
Add/Remove Channel "B"
Tap
to/from a call
*This feature is not available during intercom or mobile calls.
** Before using Hot-Dial, configure the number via the Cardo Community.
*** If 2 mobile phones are paired directly to your scala rider G9, set one to use as
default for outgoing calls.
Volume / Rewind
Channel B / FM
Say this:
<<Buddy Name>>
"Call Intercom"
"Music ON"
"Radio ON"
"Radio OFF"
"Next Station"
"Previous Station"
"Next track"
"Previous track"
"Music OFF"
In Standby, press for 5 seconds
In Standby, press for 5 seconds
.
or speak any word loudly to answer by VOX
for 2 seconds
and follow the prompt from the mobile
or tap and simultaneously
for 5 seconds
and for 5 seconds
while on a phone call
while on a phone call