Related Manuals for Huck AK-175
Summary of Contents for Huck AK-175
- Page 1 AK-175 erIes neudraulIc IvetIng ools Makers of Huck ® , Marson ® , Recoil ® Brand Fasteners, Tools & Accessories Oct 20, 2016 HK1057...
- Page 2 AK-175 Series Tools Arconic Fastening Systems and Rings (HK1057)
-
Page 3: Table Of Contents
AK-175 Series Tools Arconic Fastening Systems and Rings (HK1057) ontentS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 afety . -
Page 4: Afety
Reasonable care of installation tools by operators is an important factor 3. Huck equipment must be maintained in a safe in maintaining tool efficiency, eliminating downtime, working condition at all times. Tools and hoses... - Page 5 IT SHOULD BE RETURNED TO AN The AK-175 has a rated pull pressure of over 3,500 lbs. The AUTHORIZED SERVICE CENTER. (Authorized Service AK-175 riveter will operate effectively at any air pressure Centers may be found in Tool Serivce Center Section of between 90 and 120 psi.
-
Page 6: Perating I Nstructions
IMPORTANT NOTICE: *The AK-175 has a 5/8 inch work travel and will set most rivets in one cycle. If the tool reaches the end of its travel before the rivet breaks, the hydraulic system will lug down. -
Page 7: Peration And M Aintenance T Ips
No need to add oil. If the DO NOT OVER EXTEND… by holding the upper AK-175 is damaged and leaks oil, it must be returned to trigger or turn up air pressure to try increase tool stroke. -
Page 8: Rivet Pintail Removal
AK-175 Series Tools Arconic Fastening Systems and Rings (HK1057) intail eMoval and hree iece nStallation and eMoval Rivet Pintail Removal: Once Rivet is installed, pintail must be removed 1. Point tool downward 2. Squeeze RELEASING TRIGGER “B”. CAUTION: It is necessary to remove pintail before attempting to install another rivet. - Page 9 AK-175 Series Tools Arconic Fastening Systems and Rings (HK1057) TWO PIECE JAW SYSTEM THREE PIECE JAW SYSTEM To replace JAWS, hold JAW HOLDER large end down and at a slight To replace JAWS, hold JAW HOLDER large end down and at a angle.
- Page 10 Apply a small 7. The AK-175 should not be used at temperatures amount of light weight oil to the JAWS and inside of below 35° F. unless it is first brought to room tem- JAW HOLDER prior to assembly.
-
Page 11: Three Piece Jaw Installation And Removal)
AK-175 Series Tools Arconic Fastening Systems and Rings (HK1057) roubleShooting Problem Solution First Step: 1.) Rivet Pintail is stuck in tool Lightly tap nose against a hard surface while after breaking squeezing HANDLES and pressing down the RELEASING BUTTON with tool pointing downward Pintail should then fall out, see fig. - Page 12 AK-175 Series Tools Arconic Fastening Systems and Rings (HK1057) 90 d aK-175 r arranty on iveter All Arconic Fastening Systems tools and parts have been carefully tested and checked at the factory and are guaranteed to be free from defects in material and workmanship, subject to the following conditions.
-
Page 13: A Uthorized T Ool S Ervice C Enters
Please contact your Huck Representative or the nearest indirect cause of Buyer supplied molds, material, tooling Huck office listed on the back cover for the ATSC in your or fixtures. Buyer shall give Huck written notice of claims area. - Page 14 Technology, The Future of Assembly Technology, warranty, express, implied, or statutory; all warran- The Future of Tooling Technology, and Tools of ties are contained only in Huck’s written quotations, Productivity are service marks of Huck International. acknowledgements, and/or purchase orders. It is...
Need help?
Do you have a question about the AK-175 and is the answer not in the manual?
Questions and answers
where do i send tool for repair
Send the Huck AK-175 tool for repair to the Huck office listed on the back cover of the manual for your area.
This answer is automatically generated