Table of Contents
Advertisement
Quick Links
™
Power Control Solutions
™
Dimming & Control
PowerHOUSE
TM
Portable Distribution Boxes
PowerPARTS
TM
Wiring Devices
Portable Single Dimmers
PowerRACK
TM
Rolling Distribution Racks
WeldingRACK
TM
6kW, 12kW and 24kW
WR6
User Manual
The Lex Products 6kW, 12kW
and 24kW portable dimmers
comprise a unique portable
dimming solution that can be
used individually or as part of a
dimming system.
LM-FD3-000
Advertisement
Table of Contents
Summary of Contents for Lex Products FD3-6KW
- Page 1 Portable Single Dimmers PowerRACK Rolling Distribution Racks WeldingRACK 6kW, 12kW and 24kW User Manual The Lex Products 6kW, 12kW and 24kW portable dimmers comprise a unique portable dimming solution that can be used individually or as part of a dimming system.
-
Page 2: Table Of Contents
This manual is furnished exclusively to support the locating and Installation operation of Lex Products Single Portable Dimmers. All concepts and ideas are the sole property of Lex Products and are not Set-Up and Operation to be duplicated or utilized in any manner without written Maintenance permission. -
Page 3: Components
5-Pin XLR DMX Input Inlet Non-Dim/Dim Switch CRMX/WDMX Uplink Switch Lamp Warner Switch 5-Pin XLR DMX Thru Receptacle Status Quo Switch Uplink Switch Control Panel Detail Fig. 2 Light Stand Channel Heat Sink Fig. 3 Contact Lex Products: 800.643.4460 info@lexproducts.com... -
Page 4: Introduction
Portable Single Dimmers Introduction The Lex Products Single Portable Dimmers comprise a unique portable dimming solution that can be used individually or as part of a dimming system. This product range is ideally suited for: • Motion Picture Production • Television Production •... -
Page 5: Installation
Line • Connect the FD3-6KW or FD3-12KW panel mounted power input plug (see Fig. 4) to a branch circuit protected 120VAC 60Hz power source using a cable that is properly grounded and appropriately rated. The acceptable input voltage range for this unit is 95- 130VAC. -
Page 6: Set-Up And Operation
• The dimmer will function as a switch on or off. • Set the ‘NON DIM/DIM’ switch to ‘NON DIM’ • The relay function may be controlled locally by the fader or remotely via DMX512-A. • To switch the relay locally, rotate the rotary dial the ‘-5’ designation to close the circuit. • To switch the relay via DMX, raise the level past 50% to close the circuit. Contact Lex Products: 800.643.4460 info@lexproducts.com... -
Page 7: Maintenance
Ƚ Check to see if the NON-DIM mode is activated and the relay has been turned on manually. Ƚ If the load remains on, the power device may have failed. Contact Technical Services at 1.855.LEX.1002 Technical Support The staff at Lex Products is willing and available to help in any way possible. If you have questions or need technical advice or suggestions regarding this product, please contact Lex at 1.855.LEX.1002 or e-mail Lex at support@lexproducts.com. Business hours are Monday through Friday, 8:30 am – 5:00 pm ET and PT. -
Page 8: Additional Resources
Produced in the United States of America Shelton CT 06484 Sun Valley, CA 91352 800.643.4460 All Rights Reserved. 203.363.3738 818.768.4474 203.363.3742 Fax 818.768.4040 Fax Lex Products logo and lexproducts.com are WE DELIVER THE POWER trademarks or registered trademarks of Lex Products in the United States, other countries, or both. LM-FD2-000...
Need help?
Do you have a question about the FD3-6KW and is the answer not in the manual?
Questions and answers