Weiser SmartCode 5 Installation Manual

61891 / 01
GED1495
Installation Guide
Weiser
Required Tools
1-866-863-6584
www.weiserlock.com
Additional Tools (depending on application)
Use and programming
instructions are located on the
reverse side of this document.
3
Adjust the backset of latch (if needed)
A B
Hold the latch in front of the If the latch holes are
door hole, with the latch face centered in the door hole, no
flush against the door edge. adjustment is required.
Proceed to step 4.
If the latch holes are NOT
centered, adjust latch. See
"Latch Adjustment."
A / A2
Latch Adjustment (only if needed)
180°
7
Disassemble interior assembly and load battery pack
A B C
L
M
Make sure
turnpiece is
N in the vertical
position.
AA x4
D
L
Do not install
Ensure correct polarity. For best results,
battery pack yet!
use new non-rechargeable Alkaline
batteries only.
11
Install strike
Longer screws install
closest to door jamb.
B
B1 (2x)
B2 / B3
(2x)
Parts in the Box
Latch and Strike Exterior Assembly Interior Assembly
A B
E
K
C
A2
F
D
G
Q
P
B1
J H
B2
R S
B3
4
Install latch
For doors with chiseled edge For doors without chiseled edge
A
A2
B
A
C (2x)
C D
wood
block
8
Perform the Inclusion process
"Inclusion" refers to the process in which the lock is added to a Z-Wave controller.
A B C
Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave
controller, and initiate the Inclusion process at the controller. Refer to your
Z-Wave control system instructions for more information.
Press button "A" on the lock one time to include it in your system. The
controller and lock must remain stationary for a total of 60 seconds during
the Inclusion process.
L
Button
Z-Wave
12"
"A"
Controller
305 mm
If Inclusion is unsuccessful, initiate the Exclusion process at the controller,
then press button "A" on the lock one time. Once the lock is fully excluded
from the system, repeat the Inclusion process.
12
Program the lock
Programming
instructions are
located on the
reverse side of
this document.
1
Check dimensions
L 2-3/8" (60 mm)
or
1-3/8" — 1-3/4"*
2-3/4" (70 mm)
35 mm — 44 mm*
M
1-1/2" 2-1/8"
N or
38 mm 54 mm
Additional door preparation may be
required for doors with 1-1/2" (38 mm)
holes. Consult the drilling instructions at
www.weiserlock.com/doorprep.
5
Prepare exterior keypad
For doors with 2-1/8" (54 mm) holes
2-1/8"
54 mm
E
For doors with 1-1/2" (38 mm) holes
F
1-1/2"
38 mm
9
Install interior assembly
A
K
Ensure tight cable connection.
N
L
C D
13
Install the battery cover and re-key the lock
A B Select models only:
S
M
ball
tip R (3x)
Keep "S" in a safe place, as you will
need it to access the back panel for
additional programming.
2
Determine required latch and extend latch bolt
For doors with chiseled edge
A
1"
25 mm
*Service kits for 2-1/4"
(57 mm) thick doors are
available through Weiser.
6
Install keypad and mounting plate
A B
Cable goes
underneath latch
G
C
Keep parallel to
edge of door
G
Tighten
screws
evenly
Q (2x)
10
Perform door handing process
B
This step will teach your lock the orientation of your door
and is crucial to lock operation.
A Press and hold the
Lay cable
Lock button while
flat against
installing battery
the interior
pack (L).
housing.
Hold button until the
latch bolt starts
moving on its own.
HOLD
P (2x)
latch bolt
Template
C
If your door requires drilling, cut out the template and place it on the exterior side of the door.
Complete door drilling instructions are available at www.weiserlock.com/doorprep.
Edge Face
J
Fold
If needed, re-key the lock to
work with your existing key.
See the supplied SmartKey
Centerline
Re-key instructions for more
information.
2-3/8" (60 mm)
2-3/4" (70 mm)
Backset
For doors without chiseled edge
A2
Route cable
through center hole,
then push cable
into side hole.
K
center hole
side hole
D
Insert key and test latch.
H
If latch does not extend or
retract smoothly, adjust
screws (Q).
Remove key when finished
Q
and make sure the latch
bolt is fully extended.
B
L
Did the latch bolt retract
and extend on its own
when the battery pack
was installed?
YES NO
Door handing process Remove battery pack,
was successful! wait 15 seconds, then
Proceed to Step 11 attempt the process
after latch bolt stops again.
moving.