Occupancy Setup; Daylighting Setup; Scene Setup - Lutron Electronics Energi Savr Node QSN-4S16-S-347 Programming Manual

G
Figure
QSE-IO Input/Output Interface Programming - continued
Partition Control
1. 2. 3.
Enter Partition Programming Select Input Assign Zones
Press and hold Press and hold Press Press
3 seconds
Press simultaneously
Sequencing Control
1. 2. 3.
Enter Sequencing Programming Assign Zones Exit Sequencing Programming
Press and hold Press and hold Press and hold Press and hold
3 seconds 3 seconds
Press simultaneously Press simultaneously
H
Figure

Occupancy Setup

Set Zone Response to Occupancy Sensors
1. 2.
Enter Occupancy Setup Select Option Change Setting
Press and hold 3 seconds P d h ld 3 d Press Press
Select Scene for Occupied State
1. 2.
Enter Occupied State Setup Select Scene View Scenes 5-16
(Scenes 1-4)
Press and hold Press and hold Press Press and hold Press and hold
3 seconds 3 seconds
4.
Exit Occupied State Setup
Press and hold Press and hold
3 seconds
I
Figure

Daylighting Setup

1. 2. 3.
Select Option Set Zone Levels
Enter Daylighting Setup
P Press and hold d h ld Press
3 seconds
J
Figure

Scene Setup

2.
1. 3.
Enter Scene Setup Select Scene View Scenes 5-16 Select Scene
(Scenes 1-4)
(Scenes 5-16)
Press and hold Press and hold Press Press and hold P Press and hold Press
3 seconds 3 seconds
QSE-IO Input/Output Interface Programming - continued
Partition Control
4.
Exit Partition Programming
Refer to the Installation Instructions provided with the QSE-IO for proper DIP switch settings.
This can be used to join or detach scene activations between zones on an Energi Savr Node
units based on the position of movable walls.
To associate a QSE-IO that is set in a Partition Control configuration to an Energi Savr Node
1.
Enter Partition Control Programming. Press and hold the Program button on the QSE-IO for 3 seconds. The first output LED
will flash indicating "input 1" is selected. The input LEDs on the Energi Savr Node
Press and hold Press and hold
group.
3 seconds
2.
Select input. Tap the Program button on the QSE-IO to select an input. Corresponding LED will blink.
3.
Assign zones. Simultaneously press then release the and buttons on the Energi Savr Node
to "input 1" of the QSE-IO. A flashing 'Zone' LED indicates an assigned zone.
To unassign zones from the QSE-IO, simultaneously press then release the and buttons for the desired zone. The 'Zone' LED will
turn off to indicate the zone is unassigned.
Repeat steps 2 and 3 for each desired QSE-IO input.
4.
Exit Partition Control Programming. Press and hold the Program button on the QSE-IO for 3 seconds to exit.
Sequencing Control
Refer to the Installation Instructions provided with the QSE-IO for proper DIP switch settings.
The Energi Savr Node
start and stop automatic sequencing of scenes 5-16.
To associate a QSE-IO that is set in a Sequencing Control configuration to an Energi Savr Node
1.
Enter Sequencing Control Programming. Press and hold the Program button on the QSE-IO for 3 seconds. The first output
LED will flash indicating "input 1" is selected. The input LEDs on the Energi Savr Node
input group.
2.
Assign zones. Simultaneously press then release the and buttons on the Energi Savr Node
to "input 1" of the QSE-IO. A flashing 'Zone' LED indicates an assigned zone.
To unassign zones from the QSE-IO, simultaneously press then release the and buttons for the desired zone. The 'Zone' LED will
turn off to indicate the zone is unassigned.
3.
Exit Occupancy Setup
3.
Exit Sequencing Control Programming. Press and hold the Program button on the QSE-IO for 3 seconds to exit.
Occupancy Setup
Set Zone Response to Occupancy Sensors
Press and hold Press and hold
1.
Enter Occupancy Setup. Simultaneously press and hold the Program and Input buttons for 3 seconds. LEDs for Group 1 Inputs
3 seconds
and 'Default' for each zone will flash.
2.
Select 'Default'. Use the Option button to select 'Default'.
3.
Select Scene Set Occupied Scene
Select response. Use the and buttons to select the response type for each desired zone:
(Scenes 5-16)
Flashing LED
High
Med
Low
* CCI must be set up for Afterhours mode (see section
3.
Press Press and hold Press and hold Exit Occupancy Setup. Simultaneously press and hold the Program and Input buttons for 3 seconds to exit.
3 seconds
Select Scene for Occupied State
Note: All zones use the same 'Occupied Scene' and cannot be set on a zone-by-zone basis. All zones use the 'Off Scene' for the
unoccupied/vacant state.
1.
Enter Occupied State Setup. Simultaneously press and hold the Program and Option buttons for 3 seconds. Group 2 Input
LEDs will flash, and the 'Default' LED will light.
2.
Select Scene. Press the Option button to select a scene:
Scenes 1-4
LED Legend:
Scene LED
# Pattern
1
4.
Exit Daylighting Setup
2
Scenes 5-16
Press and hold the Option button for 10 seconds, then use the Option button to select a scene.
LED Legend:
Press P Press and hold d h ld
Scene LED
3 seconds
# Pattern
5
4.
Set Zone Levels Enter Scene Setup
6
7
3.
Set 'Occupied Scene'. Press and hold the Input button for 3 seconds to set the currently selected scene as the 'Occupied
Scene'. The 'QSM' and 'Wired' LEDs will turn on to indicate the selection is complete.
Press Press and hold Press and hold
4.
3 seconds Exit Occupied State Setup. Simultaneously press and hold the Program and Option buttons for 3 seconds to exit.
Help 1.800.523.9466
Lutron Electronics Co., Inc. | 7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
unit and/or GRAFIK Eye
TM
unit(s):
TM
unit(s) will flash sequentially through each input
TM
unit to assign each desired zone
TM
unit can be associated to a QSE-IO that is set in Sequencing Control configuration. This can be used to
TM
unit(s):
TM
unit(s) will flash sequentially through each
TM
unit to assign each desired zone
TM
Zone Response Type
Occupancy mode (auto on/off)
Vacancy mode (manual on/auto off)
Afterhours mode*
, step 3e).
= steady on = off
Default Scene LED Default
Level # Pattern Level
100% 3 50%
75% 4 25%
= flashing = off
Default Scene LED Default Scene LED Default Scene
Level # Pattern Level # Pattern Level #
100% 8 100% 11 100% 14
100% 9 100% 12 100% 15
100% 10 100% 13 100% 16
+1.888.235.2910
U.S.A., Canada and the Caribbean
Daylighting Setup
Daylighting setup should be performed during the daytime when there is consistent but indirect sunlight. Dark, cloudy days or days
with highly variable cloud cover that frequently changes the sunlight conditions should be avoided. Additionally, times of day when
the sunlight penetrates directly into the space should be avoided (such as morning or evening).
Note: Any zone set to "Receptacle" load type cannot be assigned to a daylight sensor.
QS control
®
Set Daylight Sensor Setpoint
1.
Enter Daylighting Setup. Simultaneously press and hold the Program and Input buttons for 3 seconds. LEDs for Group 1 Inputs
and 'Default' for each zone will flash.
2.
Select option. Use the Option button to select 'Opt1'.
3.
Set light levels. Use the and buttons to set the approximate light level (or, in the case of switched zones, the minimum light
level) that you wish to maintain in the space.
4.
Exit Daylighting Setup. Simultaneously press and hold the Program and Input buttons for 3 seconds to exit.
Scene Setup
1.
Simultaneously press and hold the Program and Option buttons for 3 seconds. Group 2 Input LEDs will flash, and the 'Default'
LED will light.
2.
Select Scene. Press the Option button to select a scene:
Scenes 1-4
LED Legend: = steady on = off
Scene LED Default Scene LED
# Pattern Level # Pattern
1 100% 3
2 75% 4
Scenes 5-16
Press and hold the Option button for 10 seconds, then use the Option button to select a scene.
LED Legend: = flashing = off
Scene LED Default Scene LED
# Pattern Level # Pattern
5 100% 8
6 100% 9
7 100% 10
3.
Set light levels. Use the and buttons to adjust the light level for each zone.
To make a zone unaffected, press and hold the button—the 'High', 'Med', and 'Low' LEDs will turn off. Continue holding until only
the 'Med' LED is steady on.
To make a zone affected again, press the button until you see a combination of the 'High', 'Med', and 'Low' LEDs steady on or
flashing.
4.
Exit Scene Setup. Simultaneously press and hold the Program and Option buttons for 3 seconds to exit.
Note: The fade time between scenes is factory set to 3 seconds, and is not adjustable.
CONTACT INFORMATION
World headquarters
Lutron Electronics Co., Inc.
7200 Suter Road, Coopersburg, PA
18036-1299 USA
TEL +1.610.282.3800
FAX +1.610.282.1243
Technical Support 1.800.523.9466
European headquarters
United Kingdom
Lutron EA Ltd.
LED Default
Pattern Level
6 Sovereign Close, London,
E1W 3JF UK
100%
TEL +44.(0)20.7702.0657
FAX +44.(0)20.7480.6899
100%
Technical support
+44.(0)20.7680.4481
100% FREEPHONE 0800.282.107
+1.610.282.3800
México Others
Default
Level
50%
25%
Default Scene LED Default Scene LED Default
Level # Pattern Level # Pattern Level
100% 11 100% 14 100%
100% 12 100% 15 100%
100% 13 100% 16 100%
Asian headquarters
Singapore
Lutron GL Ltd.
15 Hoe Chiang Road,
#07-03 Tower Fifteen,
Singapore 089316
TEL +65.6220.4666
FAX +65.6220.4333
Technical hotlines
France: 0800.90.12.18
Germany: 00800.5887.6635
Italy: 800.979.208
Spain: 900.948.944
Northern China: 10.800.712.1536
Southern China: 10.800.120.1536
Hong Kong: 800.901.849
Singapore: 800.120.4491
Taiwan: 00.801.137.737
Thailand: 001.800.120.665853
Other Areas in Asia: +65.6220.4666