Samsung DC32E-M Quick Setup Manual

Quick Setup Guide

DC32E-M DC40E-M DC48E-M DC55E-M
DC40E-H DC48E-H
− The colour and the appearance may differ depending on the product, and the
specifications are subject to change without prior notice to improve the performance.
− Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
Checking the Components
Contact the vendor where you purchased the product if any
components are missing.
The pictures may look different from the actual components.
Warranty card MagicInfo Software
Quick Setup Guide
(Not available in some locations) DVD
Batteries
Power cord Remote Control
(Not available in some locations)
RS232C(IN) adapter AV/Component adapter AUDIO adapter
DCE-M_DCE-H_India_QSG_BN68-07848H-00.indd 1
BN68-07848H-00
Control Panel
Speaker
DC32E-M
Speaker
Power on the product.
1
If you press the button when the product is turned on, the
control menu will be displayed.
- To exit the OSD menu, press and hold the panel key for at least
one second.
Move to the upper or lower menu. You can also adjust the value
2
of an option.
Move to the left or right menu.
3
- You can adjust the volume by moving the panel key left or right
when the control menu is not displayed.
Remote sensor
4
Press a button on the remote control pointing at the sensor on
the front of the product to perform the corresponding function.
Spacer logo (Optional)
5
Do not pull on the spacer logo using force. The logo may tear or
break off.
Reverse Side
Connects to the audio of a source device.
1
Connects to a source device using the AV/Component adapter.
2
Receives sound from a PC via an audio cable.
3
Connect to a USB memory device.
4
DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.
5
MAGICINFO IN: Use the (dedicated) DP-DVI cable when connecting a network box (sold separately).
Connects to a source device using an HDMI cable.
6
Supplies power to the external sensor board or receives the light sensor signal.
7
Connects to MDC using an RS232C adapter.
8
Connects to a source device using a D-SUB cable.
9
Connects to MDC using a LAN cable.
0
Troubleshooting Guide
Issues Solutions
The screen keeps
Check the cable connection between
switching on and off.
the product and PC, and ensure the
connection is secure.
No Signal is displayed Check that the product is connected
on the screen. correctly with a cable.
Check that the device connected to the
product is powered on.
Not Optimum Mode is
This message is displayed when a signal
displayed.
from the graphics card exceeds the product's
maximum resolution and frequency.
Refer to the Standard Signal Mode Table
and set the maximum resolution and
frequency according to the product
specifications.
The images on the Check the cable connection to the
screen look distorted. product.
The screen is not clear. Adjust Coarse and Fine.
The screen is blurry.
Remove any accessories (video extension
cable, etc) and try again.
Set the resolution and frequency to the
recommended level.
The screen appears Check that the resolution and frequency
unstable and shaky. of the PC and graphics card are set within
a range compatible with the product.
There are shadows or
Then, change the screen settings if
ghost images left on
required by referring to the Additional
the screen.
Information on the product menu and the
Standard Signal Mode Table.
Issues Solutions
The screen is too bright.
Adjust Brightness and Contrast.
The screen is too dark.
Screen colour is Go to Picture and adjust the Colour Space
inconsistent. settings.
White does not really Go to Picture and adjust the White Balance
look white. settings.
There is no sound. Check the connection of the audio cable or
adjust the volume.
Check the volume.
The volume is too low. Adjust the volume.
If the volume is still low after turning
it up to the maximum level, adjust the
volume on your PC sound card or software
programme.
The remote control Make sure that the batteries are correctly
does not work. in place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is
connected.
Check for any special lighting or neon
signs switched on in the vicinity.
2016-03-11 1:26:48