National Instruments TPC-2230 User Manual

Touch panel computer (6.5 inch/12.1 inch/15 inch)

Hide thumbs

Table of Contents

Quick Links

USER MANUAL

TPC-2230

Touch Panel Computer (6.5 in./12.1 in./15 in.)

Contents

Electromagnetic Compatibility Guidelines .............................................................................. 2

Conventions .............................................................................................................................. 3

General Information ................................................................................................................. 3

Introduction ...................................................................................................................... 3

I/O Ports............................................................................................................................ 3

System Setup ............................................................................................................................ 4

Important Safety Information ........................................................................................... 4

Setup ................................................................................................................................. 5

Panel Mounting................................................................................................................. 6

Jumpers and Connectors ........................................................................................................... 7

Jumper and Connector Functions ..................................................................................... 7

Jumper and Connector Locations ..................................................................................... 8

CMOS Clear Jumper (CN1) ............................................................................................. 10

Specifications............................................................................................................................ 10

Physical............................................................................................................................. 10

Serial Port Settings ................................................................................................................... 18

COM1 Connector Pinout .................................................................................................. 18

COM2 Connector Pinout .................................................................................................. 19

Features in Windows Embedded Standard 7 ............................................................................ 21

EWF and FBWF ............................................................................................................... 21

HORM .............................................................................................................................. 21

Drivers .............................................................................................................................. 21

Touchscreen Configuration ...................................................................................................... 22

Worldwide Support and Services ............................................................................................. 22

Table of Contents

Need help?

Do you have a question about the TPC-2230 and is the answer not in the manual?

Questions and answers

Summary of Contents for National Instruments TPC-2230

Page 1: Table Of Contents
USER MANUAL TPC-2230 Touch Panel Computer (6.5 in./12.1 in./15 in.) Contents Electromagnetic Compatibility Guidelines ................2 Conventions ..........................3 General Information ......................... 3 Introduction ........................3 I/O Ports..........................3 System Setup ..........................4 Important Safety Information ................... 4 Setup ..........................5 Panel Mounting.........................
Page 2: Electromagnetic Compatibility Guidelines
Operation of this hardware in a residential area is likely to cause harmful interference. Users are required to correct the interference at their own expense or cease operation of the hardware. Changes or modifications not expressly approved by National Instruments could void the user’s right to operate the hardware under the local regulatory rules.
Page 3: Conventions
General Information This section includes general information about the TPC-2230 Human Machine Interface (HMI). Introduction The TPC-2230 touch panel computer, an HMI based on an x86 platform, includes these key features: • Powerful processing—The TPC-2230 uses the Intel Atom processor, specifically designed for embedded, industrial applications.
Page 4: System Setup
This section includes setup information for the TPC-2230. Important Safety Information Before setting up the TPC-2230, read these safety instructions carefully. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning.
Page 5: Setup
The protection this equipment provides may be impaired if it is used in a Caution manner not described in this manual. Setup Follow these steps to set up the TPC-2230: Unpack the TPC-2230. Be sure your kit includes the following items: • The TPC-2230 HMI • Ten panel mounting clamps •...
Page 6: Panel Mounting
The system turns on immediately after you apply power. Touchscreen Calibration The TPC-2230 touchscreen should be correctly calibrated and ready to use when you power on the system. However, if the calibration is not correct or you want to choose custom calibration...
Page 7: Jumpers And Connectors
Serial port: COM1 RS232 CN16 COM2 Serial port: COM2 RS232/422/485 CN18 Power in connector Device power input MINIPCIE Mini PCIe Connection for Mini PCIe device COM2 mode Select COM2 RS232/422/485 Termination Termination resistor select TPC-2230 User Manual | © National Instruments | 7...
Page 8: Jumper And Connector Locations
Jumper and Connector Locations Figures 5 and 6 show the jumper and connector locations. Figure 5. Main Board Jumpers and Connectors—Top Side CN15 SODIMM1 CN16 CN10 CN20 CN12 CN11 MINIPCIE1 PFS1 CN17 CN13 CN18 8 | ni.com | TPC-2230 User Manual...
Page 9 Figure 6. Main Board Jumpers and Connectors—Bottom Side JDEDEBUG1 CN19 CN14 TPC-2230 User Manual | © National Instruments | 9...
Page 10: Cmos Clear Jumper (Cn1)
Table 1-7. CN1 Jumper Functions Position Function Disabled Clear CMOS Specifications This section lists the TPC-2230 system specifications. Physical 6.5 in. Weight 1.5 kg (52.91 oz) Dimensions (W × H × D) 199 mm × 152 mm × 58.9 mm (7.83 in.
Page 11 101.10 mm (3.98 in.) 7.00 mm 152.00 mm (0.28 in.) (5.98 in.) 7.00 mm (0.28 in.) 58.90 mm 7.00 mm (2.32 in.) (0.28 in.) 187.80 mm (7.39 in.) 140.80 mm (5.54 in.) TPC-2230 User Manual | © National Instruments | 11...
Page 12 186.30 mm (0.28 in.) (7.33 in.) 238.00 mm (9.37 in.) 7.0 mm (0.28 in.) 150.00 mm (5.90 in.) 7.00 mm 57.20 mm (0.28 in.) (2.25 in.) 301.60 mm (11.87 in.) 227.60 mm (8.96 in.) 12 | ni.com | TPC-2230 User Manual...
Page 13 61.10 mm (0.28 in.) (2.40 in.) 372.90 mm (14.68 in.) 296.90 mm (11.68 in.) System Intel Atom Processor E3827 1.75 GHz Video Integrated BIOS AMI UEFI BIOS 10/100/1000 Base-T 2 ports TPC-2230 User Manual | © National Instruments | 13...
Page 14 6.5 in. 600:1 12.1 in. 700:1 15 in. 700:1 Backlight Backlight lifespan 50,000 hr There may be several bright or dark pixels on the LCD. This phenomenon is Note normal in LCD manufacturing. 14 | ni.com | TPC-2230 User Manual...
Page 15 40 °C @ 10% to 95% relative humidity (noncondensing) Vibration 2 grms (5 Hzto 500 Hz) Maximum altitude 2,000 m Pollution Degree Indoor use only The front bezel is compliant with IP66. Note TPC-2230 User Manual | © National Instruments | 15...
Page 16: Electromagnetic Compatibility
For additional environmental information, refer to the Minimize Our Environmental Impact web page at . This page contains the environmental regulations and ni.com/environment directives with which NI complies, as well as other environmental information not included in this document. 16 | ni.com | TPC-2230 User Manual...
Page 17 If you need to clean the unit, use a damp cloth. Do not use liquid or spray detergents for cleaning. Make sure that the unit is completely dry and free from contaminants before returning it to service. TPC-2230 User Manual | © National Instruments | 17...
Page 18: Serial Port Settings
Serial Port Settings This section describes the TPC-2230 serial port settings. COM1 Connector Pinout The TPC-2230 COM1 serial port is RS232 only. The following figure and table show the COM1 connector pinout. Signal 18 | ni.com | TPC-2230 User Manual...
Page 19: Com2 Connector Pinout
COM2 Connector Pinout The TPC-2230 COM2 serial port is adjustable. You can set it to RS-232, RS-422, or RS-485, and it has auto data flow control capability. In other words, the TPC-2230 can automatically detect the data flow direction at this port when two-wired RS485 communication is activated.
Page 20 COM4 Mode SW2 Setting RS232 Mode RS422 Master Mode RS422 Slave Mode RS485 Mode 20 | ni.com | TPC-2230 User Manual...
Page 21: Features In Windows Embedded Standard 7
LabVIEW 2010 or later Touch Panel Module. Drivers The TPC-2230 is configured with all necessary drivers installed. If you need to reinstall any drivers, they are on the HMI Resources USB, which is included in the kit.
Page 22: Touchscreen Configuration
NI product. Refer to the Export Compliance Information at ni.com/legal/export-compliance for the National Instruments global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS.

National Instruments TPC-2230 User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for National Instruments TPC-2230

Summary of Contents for National Instruments TPC-2230

Table of Contents