Advertisement
Item
GT1455-QTBD(E)
RS-422/485 1ch
Transmission speed : 115,200/57,600/38,400/19,200/9,600/4,800bps
Connector shape
RS-422/485
Application
Terminating resistor : Open/110/330 (Switched by terminating resistor selector switch)
RS-232 1ch
Transmission speed : 115,200/57,600/38,400/19,200/9,600/4,800bps
RS-232
Connector shape
Application
Data transfer method: 100BASE-TX/10BASE-T, 1ch
Built-in
Ethernet
Connector shape
interface
(Only in models equipped with
Application
Ethernet interface)
USB (Full Speed 12Mbps), 1ch
Host
Connector shape
Application
USB
USB (Full Speed 12Mbps), 1ch
Device
Connector shape
Application
In conformance to SD standard, 1ch
SD card
Applicable memory cards : SDHC memory card, SD memory card
Application
Buzzer output
Single tone (tone length adjustable)
*7
Equivalent to IP67 (front section)
Environmental protective structure
W164(6.46) H135(5.32) D55(2.17)[mm](inch)(Excluding USB environmental protective cover) (Horizontal format)
External dimensions
W153 (6.03) H121(4.77)[mm] (inch) (Horizontal format)
Panel cutting dimensions
Weight
Approx. 0.7kg (Excluding mounting fixtures)
Compatible software package
GT Designer3 Version1.37P or later
*1 • Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal
display panel. It is impossible to completely avoid this symptom, as the
liquid crystal display comprises of a great number of display elements.
Flickers may be observed depending on the display color.
Please note that these dots appear due to its characteristic and are not
caused by product defect.
• Flickers and partial discoloration may be generated on the liquid crystal
display panel due to the display contents or the contrast adjustment.
How ever, please note that these phenomen a appe ar due to i ts
characteristic and are not caused by product defect.
• There is a difference in the display brightness and the color tones between
liquid crystal display panels. When using multiple liquid crystal display
panels, please note that there is an individual difference between them.
• A crosstalk (shadow as an extension of the display) may appear on the
liquid crystal display panel. Please note that it appears due to its
characteristic.
• When the display section is seen from the outside of the display angle, the
display color seems like it has changed. Please note that it is due to its
characteristic.
Please note that the response time, brightness and color of the liquid
crystal display panel may vary depending on the usage environmental
temperature.
Especially in the low temperature environment, the display response
becomes slow due to the characteristics of the STN liquid crystal.
Please check the display response in advance for using this product.
• When the same screen is displayed for a long time, an incidental color or
partial discoloration is generated on the screen due to heat damage, and it
may not disappear.
To prevent heat damage, the screen saver function is effective.
For details on the screen saver function, refer to the following.
GT14 User's Manual
• Just after the GOT is powered off, sometimes an image lag or partial
discoloration is generated temporary. However they are caused by the
characteristic of the liquid crystal. (After powering off, they disappear within
a few minutes.)
Appearance
White stripe patterns may appear on the surface of the resin molded part of the product. Please note that these phenomena appear due to the characteristics of the material
used in the product and are not caused by product defect.
3.3 Power Supply Specifications
Item
GT1455-QTBD, GT1450-QMBD, GT1450-QLBD
Input power supply voltage
24VDC (+10% -15%), ripple voltage 200mV or less
Fuse (built-in, not exchangeable)
1.6A
Specifications
GT1450-QMBD(E)
: D-sub 9-pin (Female)
: PLC communication
*6
(At factory shipment: 330)
: D-sub 9-pin (Male)
: PLC communication, bar code reader, RFID connection, PC communication
(Project data upload/download, OS installation, transparent function)
: RJ-45 (Modular jack)
: PLC communication, Gateway functions, PC communication
(Project data upload/download, OS installation, FA transparent function)
: TYPE-A
: Data transfer, data storage
: Mini-B
: PC communication (Project data upload/download, OS installation, FA transparent function)
: Project data upload/download, OS installation, logging data storage
GT Designer3 Version1.118Y or later
GT Designer3 Version1.37P or later
*2 Gradation inversion is a characteristic of liquid crystal displays.
Please be forewarned that depending on the displayed color, the visualization
may be difficult even within the described view angle.
*3 Using the GOT Backlight OFF function can prolong the life of the backlight.
For details on the Backlight OFF function, refer to the following.
GT14 User's Manual
*4 The touch panel is analog resistive film-type. If you touch the panel
simultaneously in 2 points or more, the switch that is located around the center
of the touched point, if any, may operate. Do not touch the panel in 2 points or
more simultaneously. Do not press the GOT display section with a pointed
material as a pen or driver. Doing so can result in a damage or failure of the
display section. For the analog-resistive film type touch panels, normally the
adjustment is not required. However, the difference between a touched
position and the object position may occur as the period of use elapses. When
any difference between a touched position and the object position occurs,
execute the touch panel calibration. When any difference between a touched
position and the object position occurs, other object may be activated.
This may cause an unexpected operation due to incorrect output or
malfunction.
*5 ROM in which new data can be written without deleting the written data.
*6 Set the terminating resistor selector switch of the GOT in accordance with the
connection type when adopting GOT multidrop connection.
For details of GOT multidrop connection, refer to the following.
GOT1000 Series Connection Manual
*7 Compliant with IP67 when the USB environmental protection cover is
attached. Not compliant when a USB cable is connected. Note that this does
not guarantee all users' operation environment. The protection is not applied
when the interface environment protection cover is removed.
In addition, the product may not be used in environments under exposition of
oil or chemicals for a long period of time, or in environments filled with oil-mist.
Specifications
GT1455-QTBDE, GT1450-QMBDE, GT1450-QLBDE
Item
GT1450-QLBD(E)
Power consumption
At backlight off
Inrush current
Permissible instantaneous power
failure time
*1
Noise immunity
Dielectric withstand voltage
Insulation resistance
Applicable wire size
Applicable solderless terminal
Applicable tightening torque
(Terminal block terminal screw)
*1 The GOT continues to operate even upon 5ms or shorter instantaneous power failure.
The GOT stops operating if there is extended power failure or voltage drop, while it automatically resumes operation as soon as the power is restored.
3.4 External Dimensions
4. Installation
4.1 Control Panel Inside Dimensions for Mounting GOT
Mount the GOT onto the control panel while considering the following control panel
inside dimensions.
30 (1.19")
1)
No
1)
PLC connection cable/PC connection cable
Applicable cable
Some cables may need to be longer than the specified dimensions when connecting
to the GOT. Therefore, consider the connector dimensions and bending radius of the
cable as well for installation.
Specifications
GT1455-QTBD, GT1450-QMBD, GT1450-QLBD
7.68W (320mA/24VDC) or less
8.40W (350mA/24VDC) or less
6.72W (280mA/24VDC) or less
7.44W (310mA/24VDC) or less
30A or less (26.4V) 2ms
Within 5ms
Noise voltage: 1000Vp-p, Noise width: 1s (by noise simulator of 30 to 100Hz noise frequency)
500VAC for 1 minute (across power supply terminals and earth)
10M or larger by insulation resistance tester (across power supply terminals and earth)
For power supply: 0.75[mm
2
] or more, For grounding: 2[mm
2
] or more
Solderless terminal for M3 screw RAV1.25-3, V2-N3A, FV2-N3A
0.5 to 0.8[N
m]
164 (6.46")
22
120 (4.73")
(0.87")
23 (0.91")
22
120 (4.73")
(0.87")
152 (5.99")
Unit: mm (inch)
4.2 Panel Cutting Dimensions
Make holes in the panel according to the dimensions list below.
Also, ensure 10mm spaces in upper and lower parts of the panel for mounting
fixtures.
152 (5.99")
153
Unit: mm (inch)
Name
GT1455-QTBDE, GT1450-QMBDE, GT1450-QLBDE
#4-40UNC
(inch screw type)
M2.6
(Metric screw type)
Panel thickness: 2 to 4mm
(0.07" to 0.15") or less
+
2
+
0.08"
(
)
6.03"
-
0
-
0
10 (0.4") or more
Panel thickness: 2 to 4mm
(0.07" to 0.15" inch)
10 (0.4") or more
Unit: mm (inch)
Advertisement
