Related Manuals for Onkyo TX-SR383
Summary of Contents for Onkyo TX-SR383
- Page 1 AV RECEIVER TX-SR383 ≫ Table of contents Instruction Manual ≫ Preparation ≫ - Connecting speakers ≫ Playback ≫ Setup ≫ Troubleshooting ≫ Appendix Front Panel≫ Rear Panel≫ Remote≫...
-
Page 2: Table Of Contents
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ What’s in the box Initial Setup Part Names Turning the power on Front Panel "Speaker System" setting (when using ZONE SPEAKER or Front Height Display Speakers) Rear Panel Automatic Speaker Setting Remote Controller (AccuEQ Room Calibration) Preparation HDMI settings... - Page 3 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Appendix Adjusting the tone Using the Sleep Timer About HDMI Listening Mode General Specifications Selecting a Listening mode Listening Mode Effects Setup Setup Menu Menu list Menu operations 1. AccuEQ Room Cal. 2.
-
Page 4: What's In The Box
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ What’s in the box 1. Main unit (1) 2. Remote controller (RC-964R) (1), Batteries (AAA/R03) (2) 3. Speaker setup microphone (1) • Used during AccuEQ Room Calibration. 4. Indoor FM antenna (1) 5. -
Page 5: Part Names
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Part Names Front Panel 3 4 5 MULTI ZONE LISTENING MODE BLUETOOTH ON/OFF CONTROL HOME ENTER RETURN B D/DVD CBL /SAT STRM BOX GAME TUNER TONE 5V / 1A ❏ For details, see ( Front Panel≫... -
Page 6: Speaker Setup
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ ON/STANDBY button 2. BLUETOOTH button: Switches the input to "BT" (BLUETOOTH). p53). 3. LISTENING MODE button: Switches the listening mode ( 4. Remote control sensor: Receives signals from the remote controller. • The reception range of the remote controller is within a distance of approx. 23'/7 m, and an angle of 30°... -
Page 7: Display
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Display 1. Lights in the following conditions. 9. Lights when the DIRECT listening mode is selected. TUNE: Receiving AM/FM radio. ST: Receiving FM stereo. RDS (Australian models): Receiving RDS broadcasting. 2. Lights in the following conditions. ZONE: When ZONE 2 is on. -
Page 8: Rear Panel
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Rear Panel ❏ For details, see ( Front Panel≫ Rear Panel≫ Remote≫... - Page 9 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ 1. BLUETOOTH antenna is built in. 2. HDMI OUT jack: Transmit video signals and audio signals with an HDMI cable connected to a TV. 3. HDMI IN jacks: Transmit video signals and audio signals with an HDMI cable connected to an AV component.
-
Page 10: Remote Controller
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Remote Controller 1. Sleep button: Used for the sleep timer that allows the unit to enter standby automatically when the specified time elapses. ( p52) 2. Input selector buttons: Switches the input to be played. 3. -
Page 11: Preparation
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Preparation Connecting speakers Connecting the TV Connecting Playback Devices Connecting Antennas Connecting the Power Cord Initial Setup Front Panel≫ Rear Panel≫ Remote≫... -
Page 12: Connecting Speakers
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Connecting speakers Speaker Installation „ 5.1 Channel System This is a basic 5.1 Channel System. Front speakers output the front stereo sound, and a center speaker outputs the sound of the center of the screen, such as dialogs and vocals. - Page 13 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ „ 7.1 Channel System (Using Surround Back This is a 7.1 Channel System that consists of the basic 5.1 Channel System p12) and added surround back speakers. Front speakers output the Speakers) front stereo sound, and a center speaker outputs the sound of the center of the screen, such as dialogs and vocals.
- Page 14 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ „ 7.1 Channel System (Using Front Height This is a 7.1 Channel System that consists of the basic 5.1 Channel System p12) and added front height speakers. Front speakers output the front Speakers) stereo sound, and a center speaker outputs the sound of the center of the screen, such as dialogs and vocals.
-
Page 15: Connections For Each Speaker Layout
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Connections for each speaker layout Connections Make correct connection between the unit's jacks and speaker's jacks (+ side to + side, and - side to - side) for each channel. If the connection is wrong, a bass „... - Page 16 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ „ Connect the Subwoofer a Subwoofer cable Connect a powered subwoofer with this unit using a subwoofer cable. Up to two powered subwoofers can be connected. The same signal is output from each SUBWOOFER jack.
- Page 17 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ „ 5.1 Channel System This is a basic 5.1 Channel System. For details of the speaker layout, refer to "Speaker Installation" ( p12). Front Panel≫ Rear Panel≫ Remote≫...
-
Page 18: Main
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ „ 5.1 Channel System + ZONE SPEAKER MAIN ROOM MAIN ROOM: This is a basic 5.1 Channel System. For details of the speaker layout, refer to "Speaker Installation" ( p12). ZONE 2: You can enjoy 2-ch audio in the separate room (ZONE 2) while performing 5.1-ch playback in the main room (where... - Page 19 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ „ 7.1 Channel System (Using Surround Back Speakers) This is a 7.1 Channel System that consists of the basic 5.1 Channel System and added surround back speakers. For details of the speaker layout, refer to p13).
- Page 20 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ „ 7.1 Channel System (Using Front Height Speakers) This is a 7.1 Channel System that consists of the basic 5.1 Channel System and added front height speakers. For details of the speaker layout, refer to "Speaker p14).
-
Page 21: Speaker Combinations
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Speaker combinations • Up to two powered subwoofers can be connected in either combination. SURROUND FRONT ZONE 2 Speaker Channels FRONT CENTER SURROUND BACK HEIGHT (ZONE SPEAKER) 2.1 ch 3.1 ch 4.1 ch 5.1 ch 6.1 ch 6.1 ch... -
Page 22: Connecting The Tv
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Connecting the TV Connect this unit between a TV and AV component. Connection method between this unit and the TV differs depending on how this unit is connected to AV component, whether the TV is equipped with an HDMI jack, and whether the TV supports the ARC (Audio Return Channel) function or not. The ARC function transmits the audio signals of the TV via an HDMI cable, and plays the audio of the TV on this unit. -
Page 23: To Arc Tv
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ To ARC TV If the TV supports the ARC (Audio Return Channel) function (*), use only the HDMI cable to connect with the TV. Use the ARC-compatible HDMI IN jack of the TV for connection. -
Page 24: To Non-Arc Tv
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ To Non-ARC TV If the TV does not support the ARC (Audio Return Channel) function (*), connect an HDMI cable and digital optical cable. If you use a cable set-top box, etc. connected to the input jack of this unit to watch TV (without using a TV’s built-in tuner), connection with a digital optical cable is not required. -
Page 25: Connecting With The Tv Using An Analog Video Cable
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Connecting with the TV using an analog video cable If an HDMI cable is not used to connect this unit with AV component, or the TV is not equipped with an HDMI jack, use an analog video cable to connect this unit with the TV. -
Page 26: Connecting Playback Devices
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Connecting Playback Devices Connecting an AV Component with HDMI Jack Mounted This is a connection example of an AV component equipped with an HDMI jack. To play 4K or 1080p video, use a high speed HDMI cable. When connecting with an AV component that conforms to the CEC (Consumer Electronics Control) standard, you can use the "Control"... -
Page 27: Connecting An Av Component Without Hdmi Jack Mounted
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Connecting an AV Component without HDMI Jack Mounted This is a connection example of an AV component unequipped with an HDMI jack. For example, when video input is connected to the BD/DVD jack, connect the audio input to BD/DVD jack, too. -
Page 28: Connecting An Audio Component
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Connecting an Audio Component This is a connection example of an audio component. Connect a CD player using a digital coaxial cable or analog audio cable. • You can also connect an audio component to OPTICAL 1 (TV) terminal using a digital optical cable. -
Page 29: Connecting Antennas
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Connecting Antennas Connect the antenna to this unit, and set up the antenna at the best position for listening while receiving radio signals. Attach the indoor FM antenna to the wall using push pins or adhesive tape. a Indoor FM antenna, b AM loop antenna Front Panel≫... -
Page 30: Connecting The Power Cord
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Connecting the Power Cord Connect the power cord after all the connections are completed. a Power cord Front Panel≫ Rear Panel≫ Remote≫... -
Page 31: Initial Setup
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Initial Setup Turning the power on After all the connections are completed, set the Automatic Speaker Setting (AccuEQ Room Calibration) ( p34) and HDMI setting ( p36). When this TV’s REMOTE unit and the TV are connected with an HDMI cable, use the OSD (On-Screen Inputs Display) that appears on the TV to make the settings. -
Page 32: Speaker System" Setting (When Using Zone Speaker Or Front Height Speakers)
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ "Speaker System" setting (when using ZONE SPEAKER or Front Height Speakers) When connecting ZONE SPEAKER or front height speakers, settings are required in the setup menu. • Make the settings before the "Automatic Speaker Setting (AccuEQ Room Calibration)"... - Page 33 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ 4. Select "a. Speaker System", and press ENTER button. 2. Ma n ua l SP S e tup a. Speaker System b. Speaker Setting c. X.Over d. Channel Level e. Channel Distance R e turn 5.
-
Page 34: Automatic Speaker Setting (Accueq Room Calibration)
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Automatic Speaker Setting (AccuEQ Room Calibration) By setting the supplied speaker setup microphone at the listening position, connection statuses of each speaker are automatically checked, and each volume is automatically set to the optimal level according to the room environment. - Page 35 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ 1. Connect the speaker setup microphone to the SETUP MIC jack of the main unit, and place it at the listening position. 2. Press BD/DVD. 3. Press 4. Select "1. AccuEQ Room Cal.", and press ENTER. •...
-
Page 36: Hdmi Settings
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ HDMI settings Make the HDMI-related settings, such as "Control" function ( p64), "ARC" function ( p64) and "Standby Through" function ( p65). Check the setting procedure in Menu operations ( p60), see the descriptions for each function, and then make the necessary settings. -
Page 37: Playback
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Playback AV Component Playback BLUETOOTH Playback ® USB Storage Device Listening To the AM/FM Radio Multi-zone Convenience functions Listening Mode Front Panel≫ Rear Panel≫ Remote≫... -
Page 38: Av Component Playback
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ AV Component Playback You can play the audio from AV components, such as Blu-ray disc players through this unit. Basic Operations Perform the following procedure when this unit is on. 1. Switch the input on the TV to the input connected to the unit. TV’s REMOTE 2. - Page 39 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Selecting audio input signals With AUDIO SEL on the remote controller, you can select audio input signals assigned to each input source. Once selected, the same audio input signal is played next time. 1.
-
Page 40: Bluetooth Playback
When the pairing procedure is competed, "CONNECT" will be displayed. If a password is requested, enter "0000". • This unit is displayed as "Onkyo TX-SR383". • To connect another BLUETOOTH-enabled device, disconnect the connection with the BLUETOOTH-enabled devices being connected and perform the pairing operation. -
Page 41: Usb Storage Device
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ USB Storage Device You can play music files stored on a USB storage device. Basic Operations Perform the following procedure when this unit is on. • When you do not use an HDMI cable but use an analog video cable to connect TV’s REMOTE with the TV, the list screens cannot be displayed on the TV. - Page 42 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ • Characters that cannot be displayed on this unit appear with "" • The USB port of this unit complies with the USB 2.0 standard. The transfer speed may be insufficient for some content you play, and sound interruptions, etc.
-
Page 43: Device And Supported Format
Furthermore, depending on the USB storage device, proper reading of the contents may not be possible. • In use of a USB storage device, Onkyo accepts no responsibility whatsoever for the loss or modification of data stored on a USB storage device, or malfunction of the USB storage device. -
Page 44: Listening To The Am/Fm Radio
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Listening To the AM/FM Radio You can receive AM and FM radio stations on this unit with the built-in tuner. Tuning into a Radio Station Perform the following procedure when this unit is on. Tuning Automatically 1. - Page 45 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Tuning Manually 1. Press TUNER to switch to "TUNER" input. 2. Press BAND repeatedly to select either "AM" or "FM ST". 3. Press TUNING +/– to select the desired radio station. • Each time you press TUNING +/–, the frequency changes by 1 step. If the button is held down, the frequency changes continuously.
-
Page 46: Presetting A Radio Station
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Presetting a Radio Station Registration Procedure You can preset up to 30 of your favorite AM/FM radio stations. After tuning in to the AM/FM radio station you want to register, perform the following procedure. -
Page 47: Selecting A Preset Radio Station
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Selecting a Preset Radio Station 1. Press TUNER. 2. Press PRESET +/– to select a preset number. Naming Registered Radio Stations You can name the preset radio stations. 1. Press TUNER. 2. Press PRESET +/– to select a preset number. 3. -
Page 48: Using Rds (Australian Models)
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Using RDS (Australian models) RDS stands for Radio Data System, and is a method of transmitting data in FM • The information displayed may not match the content delivered by the radio signals. In regions where RDS can be used, when you tune in to a radio station. -
Page 49: Multi-Zone
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Multi-zone You can enjoy 2-ch audio in the separate room (ZONE 2) while performing 5.1-ch playback in the main room (where this unit is located). The same source can be played back in the main room and ZONE 2 simultaneously. Also, different sources can be played back in both rooms. When listening to AM/FM broadcasting, you cannot select different stations for the main room and separate room. - Page 50 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ 1. Point the remote controller at the unit, and while pressing and holding the ZONE 2, press . Alternatively, press the MULTI ZONE ON/OFF button on the main unit. • "ZONE" on the display of the main unit lights up. 2.
-
Page 51: Convenience Functions
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Convenience functions Adjusting the tone You can adjust the sound quality of the front speakers. 1. Press the TONE button on the main unit to select the setting to adjust from "BASS" and "TRE". BASS: Enhances or moderates the low-tone range of the front speakers. -
Page 52: Using The Sleep Timer
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Using the Sleep Timer You can allow the unit to enter standby automatically when the specified time has elapsed. 1. Press SLEEP to set the time. Select the time from "30", "60" and "90" minutes. Select "OFF" if you do not allow the unit to automatically enter standby mode. -
Page 53: Listening Mode
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Listening Mode This unit is equipped with a variety of listening modes, and you can select the optimum listening mode for movies, TV, music, and games by pressing DIRECT, STEREO, SURR or DSP. Selecting a Listening mode 1. - Page 54 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Listening modes that can be selected with each button are as follows. For the *1 Surround back speakers need to be installed. audio formats supported by this unit, refer to "Supported Audio Formats" section. *2 Front height speakers need to be installed.
- Page 55 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Checking the input format and listening mode • PCM (32 kHz to 192 kHz sampling frequencies) • DSD (2ch only) Pressing repeatedly allows you to check the listening mode → volume → input audio format →...
-
Page 56: Listening Mode Effects
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Listening Mode Effects For the following listening modes, "DOLBY D", "DTS" or "PCM" may be displayed a maximum of 7.1 channels with additional channels such as the surround back at the beginning of the display. channel. - Page 57 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ is achieved by recording the content at a sampling rate of 96 kHz and at a sampling rate of 96 kHz and at a resolution of 24 bits. resolution of 24 bits. •...
- Page 58 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ „ STEREO between the channels. The selectable modes are CINEMA mode suitable for movies and MUSIC mode suitable for music playback. This mode outputs audio from the right and left front speakers and subwoofer. –...
-
Page 59: Setup Menu
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Setup Menu Menu list You can configure advanced settings to have a more enjoyable experience with this unit. For operation details, refer to "Menu operations" ( p60). 1. AccuEQ Room Cal. Set the connection status, volume, etc. of each speaker automatically. 2. -
Page 60: Menu Operations
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Menu operations Use the OSD (On-Screen Display) that appears on the TV to make the settings. • When you do not use an HDMI cable but use an analog video cable to connect with the TV, the operation screens cannot be displayed on the TV. -
Page 61: Accueq Room Cal
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ 1. AccuEQ Room Cal. Setting Item Default Value Setting Details Center SMALL Make the setting according to the size of the center Set the connection status, volume, etc. of each speaker automatically. ( p34) speaker and low-range reproduction capability. - Page 62 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ „ c. X.Over Setting Item Default Value Setting Details Surr.Back SMALL×2 Make the setting according to the size of the Change the settings of crossover frequencies. surround back speakers, low-range reproduction capability and the number of connected speakers. Setting Item Default Value Setting Details...
- Page 63 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Setting Item Default Value Setting Details Setting Item Default Value Setting Details Front Height R 0 dB Select a value between "-15 dB" and "+15 dB" (in 1 Front Height L 10.0ft/3.0m Specify the distance between each speaker and dB increments).
-
Page 64: Input Assign
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ 5. HDMI Setup • Default values vary depending on the regions. • The unit of distance can be switched by pressing the button on the remote controller. When using the unit "feet", the setting is available in increments of 0.1ft from 0.1 ft to Change the settings of the HDMI function. -
Page 65: Power Management
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ „ c. Standby Through „ d. 4k60p Setting Play the video and audio of an HDMI-connected player on the TV even if the unit When using a TV supporting 4k/60p, you can change the setting according to the is in standby mode. -
Page 66: Quick Menu
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Quick Menu Menu operations While checking the display of this unit, you can adjust the settings you frequently use. 1. Press the Q button on the remote controller. 2. Select the item with the cursors of the remote controller, change the setting with •... - Page 67 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ "CH1/CH2": Main and sub channels are output at the same time. Dolby Pro Logic II Music listening mode. The smaller the setting value, the more concentrated sound in the center speaker. The larger the setting value, the more „...
- Page 68 2 munites, and then plug it back in. • Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s malfunction. Before you record important data, make sure that the material will be recorded correctly.
-
Page 69: When The Unit Is Operating Erratically
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ When the unit is operating erratically ❏ Resetting the unit (this resets the unit settings to the default) If the restart of the unit does not solve the problem, reset the unit, and restore all the settings to the factory default at the time of purchase. This may solve the problem. If the unit is reset, your settings are restored to the default values. -
Page 70: Troubleshooting
If the unit still does not turn on, avoid resetting it and unplug the power cord. Then contact your Onkyo authorized service company / center. WARNING: If smoke, smell or abnormal noise is produced by the unit, unplug the power cord from the outlet immediately, and contact the dealer or Onkyo Support. - Page 71 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ ❏ No sound from a connected player • Change the input selector on this unit to the position of the terminal to which the player is connected. • Check the digital audio output setting on the connected device. On some game consoles, such as those supporting DVD, the default setting may be off.
-
Page 72: X84; Listening Modes
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ „ Listening Modes • To enjoy digital surround playback in formats such as Dolby Digital, you need to make a connection for audio signals with an HDMI cable, digital coaxial cable or digital optical cable. Also, audio output need to be set to Bitstream output on the connected Blu-ray Disc player, etc. •... -
Page 73: X84; Linked Operation
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ ❏ Images flicker • The output resolution of the player may not be compatible with the resolution of the TV. If the player is connected to this unit with an HDMI cable, change the output resolution on the player. - Page 74 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ „ BLUETOOTH function • Unplug and plug the power cord of the unit, or turn off and on the BLUETOOTH-enabled device. Restart of the BLUETOOTH-enabled device may be effective. • BLUETOOTH-enabled devices must support the A2DP profile. •...
- Page 75 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ ❏ "USB Error 4 (I/U ERR4)" appears on the display. • The power requirements of the USB device are too high for this receiver. Switch off the receiver and reconnect the USB to the receiver. „...
- Page 76 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ ❏ The OSD is not displayed on the TV • The TV system (PAL/NTSC) setting on this unit is not suitable for your country or region. Switch the setting with the following procedure. 1.
-
Page 77: About Hdmi
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ About HDMI Compatible functions devices can be reproduced on the TV with even more colors. x.v.Color™: HDMI (High Definition Multimedia Interface) is a digital interface standard for This technology reproduces even more realistic colors by expanding the color connecting TVs, projectors, Blu-ray Disc/DVD players, digital tuners, and other gamut. -
Page 78: Supported Resolutions
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Supported resolutions HDMI IN: • Copyright protection technology: HDCP1.4/HDCP2.2 • Color space (Color Depth): – 720×480i 60Hz, 720×576i 50Hz, 720×480p 60Hz, 720×576p 50Hz, 1920×1080i 50/60Hz, 1280×720p 24/25/30/50/60Hz, 1680×720p 24/25/30/50/60Hz, 1920×1080p 24/25/30/50/60Hz, 2560×1080p 24/25/30/50/60Hz, 4K (3840×2160p) 24/25/30Hz, 4K SMPTE (4096×2160p) 24/25/30Hz : RGB/YCbCr4:4:4 (8/10/12 bit), YCbCr4:2:2 (12 bit) -
Page 79: General Specifications
Contents Preparation Playback Setup ≫ ≫ ≫ ≫ General Specifications „ Amplifier Section 531/530 kHz - 1602/1700 kHz (Others) Preset Channel Rated Output Power With 8 ohm loads, both channels driven, from 20-20,000 Hz; rated 80 watts „ BLUETOOTH Section per channel minimum RMS power, with no more than 0.08% total harmonic distortion from 250 milliwatts to rated output. - Page 80 Contents Preparation Playback Setup ≫ ≫ ≫ ≫ Power Consumption Analog 270 W RCA (BD/DVD, CBL/SAT, CD) 0.2 W (Full Standby mode) (North American and Taiwanese) „ Audio Outputs 0.3 W (Full Standby mode) (Others) 0.8 W (Standby mode (HDMI Control: ON)) Pre Out Dimensions (W ×...
- Page 81 SN 29403403_EN (C) Copyright 2018 Onkyo & Pioneer Corporation Japan. All rights reserved. H1802-0...
Need help?
Do you have a question about the TX-SR383 and is the answer not in the manual?
Questions and answers