MaxiiPower Vi2202 Installation Manual

Vi2202 Two-port 60W PoE++ Midspan Installation Manual
The MaxiiPower Model Vi2202 is a unique 2-port PoE Midspan designed for
the most demanding power applications of 10/100/1000 Base-T networks.
With the ability to provide up to 65W on a single port, it is the most cost
effective method for powering PTZ domes cameras with heaters and
blowers. The Midspan is compliant IEEE 802.3af, IEEE 802.3at standards
and 60W PoE application.
The Vi2202 can virtually meet requirements of any high power PoE
application. Its unique internal control system enables it to handle both
single PD and dual PD PoE devices. A highly reliable internal power supply
can provide up to 65W shared between 2 ports. For applications requiring
2-ports of PoE++, it can be used with Vigitiron's Vi1120 external power
supply to provide up to total 120W PoE power.
The Midspan is equipped with LEDs to provide power status. No IP setting
or configurations are required and it can completely transparent to the
Ethernet network and higher layer protocols.
The Vi2202's compact design dual channel design is smaller, lighter and
easier to fit in environmental enclosures than most single channel power
supplies.
Important Safety Warning
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Install in accordance with the manufacturer's instructions.
- This installation should be made by a qualified service person and should
conform to all local codes.
- DO NOT bundle UTP signal wires in the same conduit as high-voltage
wiring.
- To reduce the risk of fire or electrical shock, do not expose these products
to rain, moisture, dripping or splashing.
- No objects filled with liquids, such as vases, shall be placed on Vigitron
equipment.
- DO NOT install the unit in a place where the operating ambient tempera-
ture exceeds 75° C.
- Make sure that the external power supply output voltage is in the recom
mended range.
- Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus that produce heat.
- Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long
periods of time.
- Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as a power
supply cord or plug is damaged, liquid has been spilled, or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
- The mains plug is used as the disconnect device and shall remain readily
operable.
RISK OF ELECTRIC SHOCK
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
DO NOT OPEN
The Smart Choice for Transmission Solutions
WARNING! - To reduce the risk of fire or electric shock, do not expose
this apparatus to rain or moisture. This apparatus shall not be exposed to
dripping or splashing and no objects filled with liquids, such as vases shall
be placed on the apparatus.
WARNING! - This apparatus is a Class I product. This product must
be connected to a mains socket outlet through an AC to DC Power supply
when using DC input.
WARNING! - The mains plug is used as the disconnect device and
shall remain readily operable.
Application Drawing
Vi2202
Network Switch
110/220VAC
Vi2202
Vi1120
IP Camera-end Installation
- Connect the UTP cables from the IP camera or other PoE powered device
to the upper RJ45 connectors of Vi2202. The cable must be a cat5/6 with a
maximum length of 100m (328 feet)
Ethernet Switch/NVR-end Installation
- Connect the UTP Cable (cat5/6) from the Ethernet switch to the standard
Ethernet port on the lower RJ45 connector of Vi2202. The total length of
UTP cable from network switch to the powered PoE device should not
exceed 100m (328 feet).
The Vi2202 is able to provide total 60W PoE output using its built-in 65W
power supply. If more power needed you can use Vi1120 external power
supply.
PoE Output up to 60W:
- Plug the AC power cord provided with the unit to the mains.
PoE Output up to 120W:
Warning: Unplug the AC power cord from the unit and
the mains.
- Connect the UTP Cable (cat5/6) from the Ethernet switch to the standard
Ethernet port on the lower RJ45 connector of Vi2202.
- Connect the the DC output connector of the Vi1120 to the DC input
connector of the Vi2202.
- Connect AC power cord of the Vi1120 to the mains.
Ethernet Extenders
60W IP Camera
60W PoE and data at
Cat-5
extended distance Cat-5
Vi2301A
60W PoE and data at
standard distance Cat-5
60W IP Camera
www.vigitron.com
TM
Vi2301A
60W IR