Table of Contents
Advertisement
DMX 512 CONTROLLER SERIES
This product manual contains important information about the safe installation and
use of this projector. Please read and follow these instructions carefully and keep this
manual in a safe place for future reference.
DMX Controller
DMX Controller
USER MANUAL
USER MANUAL
CROCODILE 2024
Advertisement
Table of Contents
Related Manuals for Konuo CROCODILE 2024
Summary of Contents for Konuo CROCODILE 2024
- Page 1 DMX 512 CONTROLLER SERIES CROCODILE 2024 DMX Controller DMX Controller USER MANUAL USER MANUAL This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference.
-
Page 2: Table Of Contents
DMX 512 CONTROLLER SERIES Table of contents Table of contents parameters safety use cautions contents in the package cable Singal DMX 512 address distribution Signal cable link and scanner address setting Operation panel view Front panel function area instruction uplex key area LCD display Edit scanner chase... -
Page 3: Parameters
DMX 512 CONTROLLER SERIES Thanks for using crocodile series scanner console! The console has internationally standard DMX512 signal output. Before operation, please refer to the use's manual carefully. 1 parameters Output signal specifications DMX 512/1990 internationally standard 504 channels Total number of channels scanner Number of scanners Max.number of channels for the... -
Page 4: Contents In The Package
DMX 512 CONTROLLER SERIES 3 Contents in the package Crocodile series console Crocodile series user's manual Power adapter 4 Signal cable It use double-shield wire with the specified impedance of 120 ohms, and if the cable exceeds 200 meters long or there are too many scanners a signal amplifier should be added, and a terminal resistor should be added to the last scanner(120 ,1/4W). -
Page 5: Dmx512 Address Distribution
DMX 512 CONTROLLER SERIES 5 DMX512 address distribution onsole uses 1 to 504 channels of dmx512 so it can control the scanners. With no more than 24 channels. The address is distributed as follows Scanner dmx starting address Scanner serial number Decimal system Scanner address switch location 1 ON... -
Page 6: Signal Cable Link And Scanner Address Setting
DMX 512 CONTROLLER SERIES 6 Signal cable link and scanner DMX address setting 1#Scanner 2#Scanner 12#Scanner DMX Address : 001 Address : 025 Address : 265 SINCE 2006 SINCE 2006 SINCE 2006 SINCE 2006 Ch10 Ch11 Ch12 Ch13 Ch14 Ch14 Ch15 Ch16 CH17... -
Page 7: Front Panel Function Area Instruction
DMX 512 CONTROLLER SERIES SINCE 2006 SINCE 2006 SINCE 2006 SINCE 2006 Ch10 Ch11 Ch11 Ch12 Ch13 Ch14 Ch15 Ch16 CH17 Ch18 Ch19 Ch20 Ch21 Ch21 Ch22 Ch23 Ch24 EDIT SET X / Y SET X / Y DELETE EDIT LIGHT CYCLE 10 11... - Page 8 DMX 512 CONTROLLER SERIES * Edit program state - Select chase number and controlled scanner number. Press number key one time to select edit chase number and then press number key again to P1-P24 select the number of scanner want to be controlled. Number key area * Running program - Select chase number expect to run.
-
Page 9: Uplex Key Area
DMX 512 CONTROLLER SERIES 9 Duplex key area * Delete the chase or chase step during programming elete the current chase step. ressing 3 seconds to delete all steps of current. [DELETE] [SET X/Y] - Press [DELETE] to cancel the X-Y channel assignment. -
Page 10: Lcd Display
DMX 512 CONTROLLER SERIES 10 LCD display Display Specific information XXXXXX XXXX Model and version number S/N:0020-02-2727**** Series Number and Test condition TEST OK [??] -- Input chase / step number RUN Chase[??] [01] -- Step number of chase [01][00.0][00.0] 1st [00.0] -- Chase running time Last [00.0] -- Chase cross speed RUN Chase[??]... -
Page 11: Edit Scanner Chase
DMX 512 CONTROLLER SERIES Press [EDIT] and [SET X/Y], select scanner by P1-P20 ( Set X/Y for all scanners Set X-Y if not select scanner by P1-P20), press SA/SB/SC to select relative channel to X [ ] Y [ ] assign to joystick or press [DELETE] to delete previous assignment setting * Press MANUAL during program running: [??] -- Display current running Chase / Step... -
Page 12: Special Scene Presentation
DMX 512 CONTROLLER SERIES 4 Press [CROSS MODE] to change the running mode -- refer to 9. Duplex key instruction. 5 If you want to run program in manual and automatic at the same time, please set as following steps. 1) Press [MANUAL] and [RELEASE CHANNELS] and then LCD display (12345678;... -
Page 13: Conventional Dimmer Control
DMX 512 CONTROLLER SERIES 15 Dimmer control Distributed control In the status of non-programming, press SCAN/LIGHT and the indicating light ON to enter dimmer function; Press SA/SB/SC to select relative dimmer channel. Move sliders of it to change dimmer. New features 1.Auto-save last running program when switch off or power off and continue play last running program while switch ON or power ON again.
Need help?
Do you have a question about the CROCODILE 2024 and is the answer not in the manual?
Questions and answers