Subscribe to Our Youtube Channel
Summary of Contents for DynaQuip Controls WaterCop CLASSIC
- Page 1 Owner’s Manual/ CLASSIC Installation Guide DynaQuip Controls • 10 Harris Industrial Park • St. Clair, MO 63077 Tel. 800-545-3636 • Fax. 636-629-5528 • www.watercop.com...
-
Page 2: Table Of Contents
Flood sensors, which detect water from a leak or overflow, house a wireless radio transmitter that sends a signal to the WaterCop to turn off your water supply . ® DynaQuip Controls • 10 Harris Industrial Park • St. Clair, MO 63077 Tel. 800-545-3636 • Fax. 636-629-5528 • www.watercop.com... - Page 3 St . Cl air Co nt ro ls, In Dy na Qu ip co p. co m w w w .w at er Probe DynaQuip Controls • 10 Harris Industrial Park • St. Clair, MO 63077 Tel. 800-545-3636 • Fax. 636-629-5528 • www.watercop.com...
-
Page 4: General Safety Information
® reducers . Install 18” downstream from existing indoor water meters to allow for future meter maintenance . DynaQuip Controls • 10 Harris Industrial Park • St. Clair, MO 63077 Tel. 800-545-3636 • Fax. 636-629-5528 • www.watercop.com... -
Page 5: Placement Of Flood Sensors
When water comes in direct contact with a flood sensor, an RF (radio frequency) signal is transmitted to the WaterCop ® the valve closes, turning off the water source to protect the building from additional water damage . DynaQuip Controls • 10 Harris Industrial Park • St. Clair, MO 63077 Tel. 800-545-3636 • Fax. 636-629-5528 • www.watercop.com... -
Page 6: Specifications
The user is cautioned that changes and modification made to the equipment without the approval of the manufacturer could void the user’s authority to operate this equipment. DynaQuip Controls • 10 Harris Industrial Park • St. Clair, MO 63077 Tel. 800-545-3636 • Fax. 636-629-5528 • www.watercop.com... -
Page 7: Additional Components Available For Your Watercop
20 feet of an outlet or, install an outlet near the WaterCop . Comply with ® ® all local codes. DynaQuip Controls • 10 Harris Industrial Park • St. Clair, MO 63077 Tel. 800-545-3636 • Fax. 636-629-5528 • www.watercop.com... -
Page 8: Manually Test The Valve
6 . Repeat steps 2 through 5 until you have tested each sensor directly in the locations you wish to monitor . DynaQuip Controls • 10 Harris Industrial Park • St. Clair, MO 63077 Tel. 800-545-3636 • Fax. 636-629-5528 • www.watercop.com... -
Page 9: Troubleshooting
. The water supply must be shut off prior to installation of the WaterCop ® DynaQuip Controls • 10 Harris Industrial Park • St. Clair, MO 63077 Tel. 800-545-3636 • Fax. 636-629-5528 • www.watercop.com... -
Page 10: Additional Part Requirements
6 . Use tube cutter to cut copper tube at the locations you marked . Careful, there will probably still be some water in the line . 7 . Remove any burrs from the tube ends and clean ends . DynaQuip Controls • 10 Harris Industrial Park • St. Clair, MO 63077 Tel. 800-545-3636 • Fax. 636-629-5528 • www.watercop.com... -
Page 11: Solder Fittings
3 . Arrange the switches in any combination (on or off position) . Write down the code combination you selected . Example: 1-on, 2-off, 3-off, 4-on, 5-off, 6-on, 7-off, and 8-off . DynaQuip Controls • 10 Harris Industrial Park • St. Clair, MO 63077 Tel. 800-545-3636 • Fax. 636-629-5528 • www.watercop.com... -
Page 12: Changing The Transmitter Code
. This procedure should only be necessary in emergencies . CLASSIC DynaQuip Controls • 10 Harris Industrial Park • St. Clair, MO 63077 Tel. 800-545-3636 • Fax. 636-629-5528 • www.watercop.com DQ PART NUMBER 192506 REV. C...
Need help?
Do you have a question about the WaterCop CLASSIC and is the answer not in the manual?
Questions and answers