SLIK PRO 330DX Operating Instructions

Operating the Center Column
A
B
Possible to lock with two ways as follows.
A. by Screw-type center column stopper.
B. by Twist-type center column locking nut.
Screw-type center column stopper will be steady, while sideslipping.
Twist-type center column locking nut will be no sideslipping, but not enough to
stop sometimes.
Removing the Center Column
Caution
Remove the Rubber Stopper from
Always remove the Pan Head
the Bottom of the Center Column.
when replacing the Center Column.
Loosen the Center Column Stopper
and the Locking Collar, and then
pull out the Center Column.
Options
SHORT CENTER COLUMN FOR PRO 300 SERIES
By using the optional Short Center Column, you can obtain the lowest
camera height.
Care of the Tripod
・DO NOT apply any grease or oil to this product.
・Clean with a mild detergent and a soft cloth only.
・DO NOT use close to flame. Avoid extreme heat.
Slik corporation reserves the right to make changes in design and/or improvements on the products without any obligation and advanced notice.
SLIK CORPORATION
853 Kayama, Hidaka city, Saitama 350-1231, Japan Phone 81-42-989-2141, Fax. 81-42-985-0210 ©2004
NO YES
To avoid unnecessary camera vibrations, try to keep the Center Column
height to a minimum.
Also use the larger legs first, when extending the legs.
Prohibition
Insert the new replacement Center Please do not turn the Center
Column through the top, and tighten Column Stopper without a Center
the Locking Collar. Column &/or an optional Short
Always be sure to return the Rubber Center Column. The internal parts
Stopper back on the bottom of the may be damaged.
Center Column, as this prevents the
Center Column from being acciden-
tally pulled out.
Storage
Washer Ring
Remove the Vertical Tilt Handle from the Pan Head, and screw into the
back of the Pan & Tilt Handle.
Make sure the washer ring on the thread stays on with the handle.
THINNER
OIL
Printed in Thailand.
R PRO 300 SERIES
Operating Instructions
Thank you very much for choosing SLIK PRO 500 DX Tripod.
The SLIK Corporation has designed your tripod to be a sturdy,
rugged, dependable product that will provide you with many years of
satisfactory use.
Please take a few moments to read this operating instruction carefully
before use so that you can take full advantage of your Tripod's many
fine features.
Retain this operating instruction in case you might want to refer back to it.
Caution
This caution icon refers to information pertaining to important safety
procedures in preventing injuries, or damages which may occur as a
result of mishandling this product.
Prohibition
This prohibited icon refers to information pertaining to prohibited con-
tents. Please refer to instructions closely to avoid accidents.
D078E-1
Components
Pan Head
Center Column Stopper
Center Column
3-Position Leg Angle
Adjustment Locks
Center Column Locking Nut
Soft Grip
Protrusions for
Replacement
Leg
Leg Lock Lever
Rubber Leg Tip
Rubber Stopper
Leg Lock
PRO 330DX, PRO 330DX-B
Caution
Soft Grip is consumption and cannot be used permanently.
Please replace it whenever ragged.
Carrying the Tripod Setting up
Prohibition Caution
Carrying a tripod with a camera left on can Prevent accidental equipment fall, or tripod tip-
result in unexpected accidents. We therefore, ping over, by making sure all levers, knobs,
recommend you to remove your camera while and handles on the tripod are securely tight-
carrying the tripod. ened, and that all three legs are opened all the
way.
Specification
PRO 330DX, PRO 330DX-B
Length folded
Max. operating height 1,600mm
Max. center column ext. 360mm
Weight
PRO 340DX
Length folded
Max. operating height 1,470mm
Max. center column ext. 310mm
Weight
Pan Head
Quick Release Platform
Quick Release
Lock Lever
Pan & Tilt Handle
Handle Connecting
Main Body
Screw
Camera
Mounting Screw
Equipment that can be
used with this Tripod
Prohibition
This product has been designed
to handle equipment weighing
under 3 kgs (6 lbs 10 oz).
Do not overload.
Some equipment weighing under
3 kgs (6 lbs 10 oz), such as long
lenses, may not balance well due
to its weight distribution. In such
PRO 340DX case, please use a larger tripod.
Pan Head mounting post
Prohibition
Do not attach camera directly to the threaded
post of the Center Column.
This may damage both camera and tripod.
600mm
(23 7/12")
(63")
(14 1/6")
1.67kg
(3 lbs 11 oz)
490mm
(19 1/4")
(57 5/6")
(12 1/6")
1.58kg
(3 lbs 8 oz)
Vertical Tilt Handle
Panning Lock Knob
Mounting Wing Nut