Lenze 8200 Operating Instructions Manual page 235

Appendix
Code table
Code Possible settings
No. Name Lenze
C0410 Free configuration
v
of digital input
signals
1 NSET1−JOG1/3
NSET1−JOG1/3/5/7
(A)
2 NSET1−JOG2/3
NSET1−JOG2/3/6/7
(A)
3 DCTRL1−CW/CCW
4 DCTRL1−QSP 255
5 NSET1−RFG1−STOP 255
6 NSET1−RFG1−0 255
7 MPOT1−UP 255
8 MPOT1−DOWN 255
9 Reserved 255
10 DCTRL1−CINH 255
11 DCTRL1−TRIP−SET 255
12 DCTRL1−TRIP−RESE 255
T
13 DCTRL1−PAR2/4 255
14 DCTRL1−PAR3/4 255
15 MCTRL1−DCB
16 PCTRL1−RFG2− 255
(A) LOADI
17 DCTRL1−H/Re 255
18 PCTRL1−I−OFF 255
19 PCTRL1−OFF 255
20 Reserved 255
21 PCTRL1−STOP 255
22 DCTRL1−CW/QSP 255
23 DCTRL1−CCW/QSP 255
24 DFIN1−ON 255
14−34
Selection
Link between digital signal sources and internal digital
signals
1 Digital input X3/E1
2 Digital input X3/E2
4 Digital input X3/E4
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
3 Digital input X3/E3
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
Not assigned (FIXED−FREE)
EDB82MV752 EN 5.2
IMPORTANT
A selection made under C0007 is copied
to the corresponding subcode of C0410.
A change of C0410 sets C0007 = 255!
Selection of fixed setpoints
C0410/1 C0410/2 active
C0410/33
C0046
LOW LOW LOW
JOG1
HIGH LOW LOW
JOG2
LOW HIGH LOW
...
... ... ...
JOG7
HIGH HIGH HIGH
CW = CW rotation LOW
CCW = CCW rotation HIGH
Quick stop (via terminal LOW active)
Ramp function generator main setpoint stop
Ramp function generator input must be set
to "0" for mains setpoint
Motor potentiometer functions
Do not change 255!
Controller inhibit (via terminal LOW active)
External error (via terminal LOW active)
Error reset
Parameter set changeover
(only possible if C0988 = 0)
C0410/13 and C0410/14 must have the
same source in every parameter sets
used. Otherwise it is not possible to
change between the parameter sets
(error message CE5 or CE7).
C0410/13 C0410/14 active
LOW LOW PAR1
HIGH LOW PAR2
LOW HIGH PAR3
HIGH HIGH PAR4
DC−injection brake
Actual process controller value
(PCTRL1−ACT) must be connected to
process controller ramp function generator
(PCTRL1−RFG2)
Manual/remote changeover
Switch off I−component of the process
controller
Process controller switch off
Do not change 255!
Process controller stop (value "frozen")
Failsafe change of the direction of rotation
0 = Frequency input not active
1 = Frequency input active
Frequency input configuration under C0425
and C0426
^ 7−68
L