Advertisement
Table of Contents
- 1 Gate Frame
- 2 Hardware Pack
- 3 Extensions List
- 4 Assembling and Installing Your Gate
- 5 Positioning and Attaching the Wall Cups to Your Door Opening
- 6 How to Open the Gate Door
- 7 How to Close and Lock the Gate Door
- 8 Instructions for Gate Extension
- 9 Removing Your Gate from the Wall
- 10 Care and Maintenance
- Download this manual
Gate Instructions
Assembly and Installation Instructions
Please read these instructions carefully.
Please follow these instructions carefully to ensure that
your gate extension is properly installed. Improper
installation could result in the gate becoming dislodged
from the doorway, or unstable. Always make sure the
extension is securely attached to the gate before using. The
safety of your child is your responsibility.
Note: If using this gate at the top of stairs,the 4 Wall Cups
MUST be used . I f not use,the gate could be dislodged from
the opening.
Check that you hav e these contents:
1. Gate Frame
2. Hardware Pack which should contain:
4 - Threaded Spindle Rods
4 - Wall Cups
Important: Keep these
instructions for future
reference
It is preferable to in stall the extension on the hinge side of
the gate. If you have an application that requires additional
extensions, please contact the retailer which you
purchased your gate from. We offer, the following sizes of
extensions for your gate: 4 inch, 6 inch, 12 inch and 24
inch. They are available at most retailers that carry our
Regalo Products line of metal gates.
Contact Regalo for questions and replacement
parts. If in doubt concerning the use of your gate,
call our customer care line at 952-435-1080.
Regalo International LLC., 14305 Southcross Drive.
Suite 100, Burnsville, MN 55306.
Made in China.
WARNING:
Intended for young children aged six months through 24 months.
Check the gate regularly to see if all the hard ware and mountings
are tightened.
To prevent serious injury or death,securely install gate or
enclosure and use according to manufacturer's instructions.
Never use with a child able to climb over or dislodge the gate or
enclosure.
Never leave child unattended.
Use only with the locking/latching mechanism securely engaged.
Note:If using this gate at the top of stairs,the 4 wall Cups MUST
beused. If not used,the gate could be dislodged from the opening.
4 - Adjustable Wheel Spindles
(already assembled to the Spindle Threaded Rods)
(1)
4 - Screws
Advertisement
Table of Contents
Related Manuals for Regalo Safety Gate
Summary of Contents for Regalo Safety Gate
- Page 1 4 inch, 6 inch, 12 inch and 24 inch. They are available at most retailers that carry our Regalo Products line of metal gates. Contact Regalo for questions and replacement parts. If in doubt concerning the use of your gate, call our customer care line at 952-435-1080.
- Page 2 Gate Instructions 3. Extensions List Item NO. 12 Extension 1152 1154 1158 1160 1164 1165 1166H Important: Keep these instructions for future reference 8 Extension 6 Extension MAX Size 4 Extension 29--52 inches 29--52 inches 29--58 inches 29--38 inches 29--52 inches 29--44 inches 29--40 inches...
- Page 3 Gate Instructions Assem blin g and Installing Your Gate **Note: IMPORTANT you will notice a slight Gap between the gate door latch and the frame tube . THIS IS NOT A DEFECT . Your gate is a pressure mounted gate and this gap will disappear once you tighten your gate in the doorway.
- Page 4 Gate Instructions Step 3. Positioning and Attaching the Wall Cups to your door opening. Your gate is a pressure mounted gate. Therefore it is not necessary to use the screw attached Wall Cups to your door opening if you choose not to. However, IF YOU ARE USING THE GATE AT THE TOP OF STAIRS YOU MUST USE THE WALL CUPS.
- Page 5 Gate Instructions Step 4. You are now ready to install your gate in the doorway. Begin by positioning your gate level and centered in the doorway opening. Pull the 4 Threaded Spindle Rods out of the ends of the frame Tubes until the Flat Plastic End touches the wall. **If you are using the Wall Cups then the flat plastic ends of the Threaded Spindle Rods should go into the Wall Cups that are fastened to your wall.
- Page 6 Gate Instructions Step 5. You are now ready to do the Final Adjustment to fasten your gate firmly in the doorway. Start by turning the BOTTOM Adjustment Wheels FIRST. Continue to turn the lower Adjustment Wheels counter-clockwise until the Adjustment Wheels are firmly against the ends of the frame tubes.
- Page 7 Gate Instructions Next, tighten the top 2 Adjustment Wheels by turning them counter-clockwise. Again, make sure both sides are equal as you tighten. As you tighten the Adjustment wheels you will notice the gap between the plastic gate door latch and the frame tube is narrowing.
- Page 8 Gate Instructions Diagram G1: How to open the Gate Door. Step2 Step1 Diagram G1 Step 1: Slide the Safety Lock back. Step 2: You can now lift up the Handle Step 3: The Gate Door can now swing open. Important: Keep these instructions for future reference Diagram G2: How to close and lock the...
- Page 9 Gate Instructions Instructions for Gate Extension 1. Assemble the gate per the gate instructions. 2. Choose the side of the gate to be extended and remove the top and bottom Adjustment Wheel Spindles. 3. Assemble the gate and extension as illustrated. 4.
Need help?
Do you have a question about the Safety Gate and is the answer not in the manual?
Questions and answers