Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
HDM-8512C
DVB-C Mod with Mux, OSD
HDM-8512T
DVB-T Mod with Mux, OSD
HDM-8508C
DVB-C Mod with Mux, OSD
HDM-8508T
DVB-T Mod with Mux, OSD
HDM-8500 series
Encoder & Modulator
Variants:
12x HDMI, 1x DVB-C, 128x IP | LogoOSD, MUX, 4x DVB-C, 4x MPTS
12x HDMI, 1x DVB-C, 128x IP | LogoOSD, MUX, 4x DVB-T, 4x MPTS
8x HDMI, 1x DVB-C, 128x IP | LogoOSD, MUX, 4x DVB-C, 4x MPTS
8x HDMI, 1x DVB-C, 128x IP | LogoOSD, MUX, 4x DVB-T, 4x MPTS
Datasheet & Instruction Manual
V1.1
Advertisement
Table of Contents
Related Manuals for Blankom HDM-8512C
Summary of Contents for Blankom HDM-8512C
- Page 1 HDM-8500 series Encoder & Modulator Variants: HDM-8512C DVB-C Mod with Mux, OSD 12x HDMI, 1x DVB-C, 128x IP | LogoOSD, MUX, 4x DVB-C, 4x MPTS HDM-8512T DVB-T Mod with Mux, OSD 12x HDMI, 1x DVB-C, 128x IP | LogoOSD, MUX, 4x DVB-T, 4x MPTS...
-
Page 2: Table Of Contents
PARAMETERS → IP STREAM: ........................8 SCRAMBLER ............................9 ON SCREEN DISPLAY SETUP: ......................... 10 TROUBLESHOOTING ..........................12 PACKING LIST ............................12 IMPORTANT NOTES! ..........................13 ............................13 NSTALLATION OTES CONTACT: ............................. 14 Author: RRi - 2 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... -
Page 3: Chapter 1: Introduction
Supporting QR code, LOGO, OSD insertion for every local channel 1 ASI output (Optional as ordered) PID remapping/accurate PCR adjusting /PSI/SI editing and inserting Control via web management, and easy updates via web Author: RRi - 3 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... -
Page 4: Specifications
1/2, 2/3, 3/4, 5/6, 7/8 ≥42 dB RF frequency 50...960MHz, 1KHz step 4*RF COFDM DVB-T out (4 carriers RF out combined output) RF output level -28... -3 dBm (77...97 dbµV), 0.1db step Author: RRi - 4 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... -
Page 5: Appearance And Description
Port Power supply and Grounding Pole 12HDMI input Reset Key/Data Port Indicator Indicator ASI output port(optional) DATA Port (for IP stream input/output) NMS/CAS RF in and Loop out Author: RRi - 5 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... -
Page 6: Installation Guide
Users should make sure the 2 ends of grounding wire well electric conducted Author: RRi - 6 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... -
Page 7: Management By Web-Interface (Webif)
We start with the Network settings of the NMS- management port: We assume that the user is familiar with IP settings and already knows his own system to connect the Author: RRi - 7 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... - Page 8 NMS port. Same is done for DATA1 GbE Port and DATA2 GbE Ports where Streams can be sent IN and OUT. Author: RRi - 8 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1...
-
Page 9: Upgrading The Firmware
HDM 8500 Encoder & Modulator User Manual Upgrading the firmware: Switch ON / OFF at the rear panel for rebooting the device: Author: RRi - 9 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... -
Page 10: Save And Restore The Configuration
This method is only temporary so we recommend to use the Backup and Load function instead: Safe/Store the config.bin file on your local PC. Author: RRi - 10 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... - Page 11 HDM 8500 Encoder & Modulator User Manual Restoring this config: Select the file and start the upload: than LOAD config confirm it please… Author: RRi - 11 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1...
-
Page 12: Setting Device Time And Date Information
The unit can synchronize its Date and Time information by: your local PC via the browser or by a connected NTP server either from the internet or the local router if supported Author: RRi - 12 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... -
Page 13: Password Setting
Reset (Front panel RESET button) must be initiated. System Log Window: Log information for Kernel or System messages can be exported for your information or passing on to the developers – just in case. Author: RRi - 13 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... -
Page 14: Chapter 2: Encoder Setup
Importing an existing DVB-C RF channel is possible to pick or select one or more services out of it for later remultiplexing to the 4 new TS seen in following chapter. Author: RRi Chapter 2 Page - 1 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... -
Page 15: Parameters → Ts Config
Always Necessary after adding a service! An INPUT listing File can be imported already for Input stream addresses: Format? Need to check it… Author: RRi Chapter 2 Page - 2 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... - Page 16 Chose DATA 1 or 2, Multicast is default, Unicast can be chosen, several MC-Address and ports in STEPS, IGMP off/V2/V3 selectable, UDP or RTP as receiving IP protocols. After adding an IP Input and parsing the info's, the Service Information are shown: Author: RRi Chapter 2 Page - 3 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1...
- Page 17 : To check current whether the TS has too much Inputs: Overflow status: red color means there is too much content … please reduce the number of services accordingly. Author: RRi Chapter 2 Page - 4 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1...
-
Page 18: Dvb-C Modulator Channel
All 4 channels will be updated to the same constellation. DVB-T Modulator settings vary from DVB-C. Start Frequency (adjacent channels) and DVB-C Mode can be done with selecting the upper edit pen: Author: RRi Chapter 2 Page - 5 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... - Page 19 It is also possible to simply pass an Input to the output TS and channel. NIT descriptors can be manually added: with setting of different channels step by step… Author: RRi Chapter 2 Page - 6 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1...
- Page 20 If particular PID's should be simply bypassed from In- to Output use this: Program Modification: The multiplexed program information can be modified. For example, when point and click on the selected output service: Author: RRi Chapter 2 Page - 7 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1...
-
Page 21: Parameters → Ip Stream
Parameters → IP Stream: This encoder modulator is able to sent the 4 Transport streams (4xMPTS) to the IP Output on the GbE port through the DATA1 port. Author: RRi Chapter 2 Page - 8 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... -
Page 22: Scrambler
If chosing the scrambler Option, you need to have a connection to a CAS: Conditional Access Server and configure the needed setup values here in the Scrambler Menu: Author: RRi Chapter 2 Page - 9 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... -
Page 23: On Screen Display Setup
Browse and select the Logo or Put your logo everywhere advertisement which has been created Move the position to where it should appear on screen. Author: RRi Chapter 2 Page - 10 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... - Page 24 QR codes can be overlayed to single or selected or all output pictures: Please note: This OSD feature can only be used in the encoded channels of the encoder Modules (8 /12 HDMI). Author: RRi Chapter 2 Page - 11 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1...
-
Page 25: Troubleshooting
1 pcs (depending on country where the unit has been delivered to*) *: Some countries have extraordinary rules about the Power cord importing, so we do not attach one Author: RRi Chapter 2 Page - 12 - Date: 13. Jun. 2017 BLANKOM-HDM-8500C-T_User_Manual_EN Version 1.1... -
Page 26: Important Notes
Installation Notes All types of the IRENIS-BLANKOM family are 19“devices with 1 RU height designed for installation in 19” racks. In addition to the front panel screws an internal module support is required at the rack. Depending on the Frontend used and the operating adjustments, the RF-input port might carry DC Voltage (13V /18V, max. -
Page 27: Contact
Owiesenkehre 1 D-22177 Hamburg - Germany Managing Director: Dipl.Ing. Riccardo Rossini Commercial Register: HRB 130657 / District Court Hamburg Web: www.blankom.de E-Mail: info@blankom.de Irenis-Direct Phone: +49 40 459747 Technical Hotline: +49 40 22864848 Author: RRi Chapter 2 Page - 14 - Date: 13.
Need help?
Do you have a question about the HDM-8512C and is the answer not in the manual?
Questions and answers