Pivot Mega RAIZIN User Manual

( VS-M As of March, 2008 No.2 )
Mega RAIZIN
Voltage Stabilizer
USER'S GUIDE
Thank you for purchasing PIVOT "Mega RAIZIN". Please read these instructions carefully
before installing or using this device. Please do not lose this user's guide, as you will held liable
for the cost of reissuing it.
CAUTION
•
Do not work in areas where there is excessive exhaust
Due to vehicle exhaust emission poisoning or fire may result in a damage
to humans.
•
Safety Precautions for Installation and Checking Operations
When the key is switched to ON, there is a possibility that the fan or belt
may suddenly begin moving and cause bodily injury. When doing any
work, make sure that the key is switched to OFF and when checking
operation make sure not to put your face or hands in a close position
which could cause bodily injury.
FEATURES
Results you can 1.The unit assesses battery performance through changes in lowest voltage readings and when it has been judged to be reduced allows the user to take
count on necessary measures to improve performance (replacement, recharging, etc...) and thereby provide voltage stability to all electronic devices.
2.The condenser circuitry reduces electrical noise and provides a stable voltage supply to the ignition coil as well as all other electronic devices.
•
About Improved Performance ......
NOTE •
About Judging Battery Life ......
Voltage Stabilizer
Our newly designed three-fold (compared to Blue Raizin) large capacity condenser
and our newly designed filter circuitry results in decreases in both circuitry noise
and high frequency impedance which results in a more stable supply of voltage to
the ignition coil and all electronic devices as well as improvements in power loss.

INSTALLATION PROCEDURE

Please install safely and surely by following these
instructions.
In particular, please be very careful about
connecting the and
will cause damage to the product.
Things to prepare
.
Wrenches (Socket Wrench
.
Vinyl Electrical Tape
1 Installation Preparation
1 Remove the cable from the
2 Insulate the battery terminal with vinyl tape.
CAUTION
To prevent making any mistakes with the
and and causing a short during installation,
please make sure to insulate.
2 Installing the RAIZIN unit.
Decide installation place.
1
.
Without forcing, make sure you can connect
the two cables to the correct terminals.
.
Make sure the installation place is a flat
surface where the unit can be fixed with
double-sided tape.
Ex) The top or side of the battery or any other
flat surface near the battery. (fuse box, etc...)
If you're installing on the side surface, install so
the cables go out the bottom.
that
Do not to install in areas subject to water.
Circuitry has waterproof coating. But do not to install in areas subject to water or spray
.
with water.
If you install with the cables
going out the top, water
may enter the unit and
cause damage. Make sure
install with cables
to
going
bottom of the unit.
2 Clean off all oil and dirt from the bottom of the main
unit and affix the double-sided tape included in the kit.
3 Clean off all oil and dirt from the installation place and
fasten the main unit.
CAUTION
1.If you're installing on the side surface, the double-sided
tape will take about two hours to become secure.
During that time do not allow any vibration to the unit.
2.Reinstalling will cause the tape's adhesive strength to
1
weaken, so please do not to it.
Improper use or disregard of these warnings may result in the injury or death of people.
•
Please securely fasten the product to a stable place
Make sure to install and fasten the unit to a safe place that will not
become entangled in a fan or belt.
•
Do not crush the cable
Please do not place the unit or the wires in any place that is exposed to
high temperature nor near any rotating objects such as a fan or belt.
Wires may become broken causing a short and/or fire. Do not splash
water on the unit.
Stabilize Voltage and Know when Battery Performance is Reduced !
Installation of this product will lead to improvement in electrical aspects of your automobile but due to actual car and driving conditions
these improvements may be negligible or in some cases no change will occur.
Depending on the characteristics of the battery itself even a small change in the lowest voltage reading may signal the end of a battery's life.
WARNING
cables. Mixing these up
.
Combination Wrench)
. .
Cloth Absorbing Agent
battery terminal.
If you're installing on the top surface,
make sure the car hood will not to
hit the unit when closed.
.
Do not allow water to come
into contact with the unit.
If it is a good chance of water
coming into contact, please
cover with waterproof
sheeting.
out the
Waterproof Sheeting, etc.
CLEAN TO REMOVE
Please check the contents of the package.
A World's First: View Battery Performance via Lowest Voltage Display
Displaying two types of voltage, both "Real" and "Lowest" Voltage (world first) at
engine start makes it easy to see battery life and loss in battery performance. This
also helps to protect against trouble caused by shortages in voltage to various
electronic devices.
Make sure that and
BASIC WIRING M6 Nut
Battery terminal
Cable
Red Colored
Insulation Cap
Digital
Display
RAIZIN
Unit
3 Connect the
Remove the cover from the
1
Cable terminal
Connect the unit's
insulation cap) to the terminal of the
.
Battery terminal
Fasten with an M6 nut to the original bolt.
.
Insulate with
Fasten between the original nut and the terminal.
vinyl tape.
2 Replace the cover after completing the connection.
If the cover does not insulate properly, please use
vinyl tape to ensure proper insulation.
4 Check Wiring
Remove the vinyl tape from the
1
2 Connect the minus
3 If the wiring has been completed correctly the voltage should appear and after ten seconds
automatically shut off.
.
If voltage is not displayed = please check the connection and make sure
WARNING
Connect the unit's
5 Connect the
1 Properly connect the
terminal.
2
Connect the unit's
insulation cap) to the terminal of the
.
Fasten with an M6 nut to the original bolt.
.
Fasten between the original nut and the terminal.
If an earth terminal is installed, connect the cable to the terminal.
(See [BASIC WIRING])
OIL & DUST
6
Arranging the Cables
Mega
High Capacity System & Battery Performance Monitor
Double-sided
Main Unit M6 Nut 2
•
Do not allow water to come into contact with the unit.
The unit has been processed for water resistance but do not splash
with water when washing the car and so on.
•
This product is for DC12V cars;
installation cannot be carried out on cars with other voltage
batteries.
are connected correctly.
If an earth terminal is installed...
Battery terminal
M6 Nut
Cable
Blue Colored
Insulation Cap
Cable
Cable
terminal of the battery.
cable (one with red colored
battery cable.
terminal of the battery.
cable (with blue cap) to the battery's minus
are correct.
Please make sure to check about connecting the
cables. Mixing these up will cause damage to the product.
cable
Sparking upon Contact
Due to characteristics of the product, upon
contact of the RAIZIN'S
or upon the shorting of the flow of
current sparks may be emitted. This is not a defect.
Cable
cable terminal to the battery
cable (one with blue colored
battery cable.
Arrange the cables with the lock ties included.
User's Guide
Tape 3
Earth Terminal
Battery terminal
Cable terminal
Battery
Original Bolt
terminal
M6 Nut
Red Colored
Insulation Cap
Cable
terminal.
and
and
to the battery's
Battery
Original Bolt
terminal
M6 Nut
Blue Colored
Insulation Cap
Cable