3 CD CHANGER MINI MINI COMPONENT MAX-632P SERVICE Manual 3CD CHANGER MINI COMPONENT CONTENTS 1. Precautions 2. Specifications 3. Disassembly and Reassembly 4. Alignment and Adjustments 5. Special Circuit Descriptions 6. Troubleshooting 7. Exploded Views and Parts List 8. Electrical Parts List 9.
Signal to noise ratio 2.5% Total harmonic distortion 20Hz ~ 20KHz(±1dB) Frequency response 90 dB(1kHz 0dB) Signal to noise ratio Compact Disc 75 dB(1kHz 0dB) Channel separation 0.08%(1kHz 0dB) Total harmonic distortion Specifications are subject to change without notice. Samsung Electronics...
Page 4
5.7% of the difference between Vcc and VC (pin69) {(5.7% x (Vcc-Vc)}. Note : If the resistance connected to pin 7 changes, the phase compensation peak of focus,tracking,sled servos change. At the same time, Ôop-ampÕ dynamic range and offset voltage also change. Samsung Electronics...
Page 5
TM5 or TM6 = 22µA, This current is inversely proportional to the resistor, variable within a range of 5 to 40µA for TM3. STOP is the ON/OFF detection signal for the limit SW (or the sled motorÕs innermost cirumference). Samsung Electronics...
3. Disassembly and Reassembly 3-1 Cabinet-Top 1. Remove 9 screws holding the Cabinet-Top. 2. Lift the back of the Cabinet-Top and slide it to the rear to remove. Figure 3-1 Samsung Electronics...
Page 7
2. After power is not connected : - Turn the Gear clockwise using the hand as shown in figure 3-2-1. - Pull the Tray in the direction of arrow @. 3. Remove 4 screws $,% and lift the CD-Mecha. TRAY Figure 3-2-1 Figure 3-2 Samsung Electronics...
Page 8
1. Remove 17 screws % and then lift the Cabinet-Rear ^ and slide it to rear to remove (see arrow). 2. Remove the Main-PCB &. Figure 3-3 3-4 Cabinet-Front and Cabinet-Bottom 1. Remove 5 screws *. 2. Remove the Cabinet-Rear by pushing the ÒAÓ and ÒBÓ as shown. Figure 3-4 Samsung Electronics...
Page 9
Disassembly and Reassembly 3-5 CD Mecha TRAY STOPPER BASE MAIN Refer to the next page for timming point CD SUB PCB TRAY DISC ASS'Y HOOK CD MAIN PCB Figure 3-5 Samsung Electronics...
Page 10
3-5-3 CD Main PCB Disassembly 1. Remove the Lever-Lifter(9) from the Base-Main by releasing two hooks. 2. Remove four Rubber-CD(0) from the Lever-Lifter and then remove the Deck-CD(“). 3. Remove the Hook. 4. Remove the CD MAIN PCB with the soldering iron. Samsung Electronics...
Page 11
* Align the Gear-Cam with the Gear-Tray as shown ing Figure 3-6, then mount the Tray-Disc. Gear-Cam Gear-Cam Gear-Cam Timming Point Gear-Cam Figure 3-6 * When assembling the Tray-Disc,take extreme care not to engage with Gear-Synchro. Gear-Synchro Insert Gear-Disc Figure 3-7 Samsung Electronics...
Page 12
Remove the Gear (c) ( by pushing the hook. Lift the Gear(b) ). 10. Remove the Gear(a) 1. 11. Remove 2 screws 2 and the then remove the Feed-Motor 3. 12. Remove the Chassis-Deck (M) 4. Figure 3-8 Samsung Electronics...
Figure4-1 IF CENTER and THD Adjustment FM Antenna 30 dB FM Search Level Adjustment 75Ω Dummy SSG FREQ. 98 MHz FM IN FM SSG Adjustment point SEMI-VR(5KB) (MSR1) 5 kB “TUNED” is shown on FLT (Figure 4-2) Figure4-2 FM Auto Search Level Adjustment Samsung Electronics...
Page 14
LOCK. control screw to 2)Press REV PLAY playback REV. Mode button. PLAY MTT-150 L-CH:Turn DSR4L See the PlayBack Same as 100mV ±0.5dB to the right and diagram for out Level above on Deck 2. adjustment left R-CH:Fixed locations. Samsung Electronics...
Page 15
TP1 as in Figure R-CH: DSR1R to (7V ±5%) Deck2, then press adjustment 4-6 and read the current the right and left REC button. locations VTVM Oscilloscope VTVM Cassette Deck Audio OSC. LINE OUT AUX IN IN OUT Figure 4-6 Samsung Electronics...
Page 16
Raise NVR1703 and adjust the waveform so that its middle and (+) terminal to center of AP1. comes to ground of the oscilloscope. (Or, until the upper half Set NVR1704 to 0mV. of waveform becomes symmetrical to the bottom half,A=B) Adjust NVR1701 (arrow) for normal sound. Samsung Electronics...
(pin 29 ; 4.5V) RC16,RR17,RR26 Front PCB When the power is Replace µ-com. ON 'H' displays at pin 1 ?(5V) Connect Front PCB and Main PCB. Check the Power PCB : P/T, FUSE Check the connector Main PCB. Wafer CCW1,CCW2 Samsung Electronics...
Page 18
AQ1L,AQ1R Base B+ ? replace it. Is Mute selected ? Remove it with Remocon. Replace Headphone jack Headphone Jack short ? soldering condition. FIC3(NJU3718) pin 27 Replace FIC3(NJU3718) Check the "H" ? Check if the output line is short. Samsung Electronics...
Page 19
7.5V ? Replace LC72131 AM VT Check the LC72131 LC72131 pin 20 CONTROL ok? 0.9V 7V ? Check MIC2 pin 20 ? Check FEP interior LPF(MLPF 1L/1R) Check TDA7318 function ok? pattern, and any line output ok? disconnections. Samsung Electronics...
Page 20
Connector inserted Reinsert the connector. correctly? Check Main-PCB Front PCB Check voltage : AC 4.8V connection and the voltage of at FRONT-PCB FLT? CCW1, pins 1,2(AC4.8V) Check voltage at UIC1 Check the voltage of RZD1(-33V) pin 48(-33V) Replace UIC1 Samsung Electronics...
Page 21
Oscillate RECORD BIAS (105KHz) Mode DQ1L/1R -10V PLAY 1.4V Control DECK MECHA Check for RESET Control VF DISPLAY When power is turned ON µ-com UIC1 Control MUTE circuit Control each circuit Check VF DISPLAY VF DISPLAY Drive VF DISPLAY Samsung Electronics...
Page 22
Check Roulette Control Sensor Check oscillation of NXF100 Is Focus Search ok ? (16.9344MHZ) Does Laser function during Replace PICK UP Focus Search ? Check NIC9282 pin73 voltage Replace NIC9282 during Focus Search : 5V Replace NIC9220 or NIC9258 Samsung Electronics...
Page 23
6-3-2 Audio Output Malfunction Malfunction of Audio Output Check voltage of NIC05 : 5V Replace NIC05 Check waveform of NIC9282 Check NIC9282 soldering Check NIC9282 soldering pins 19,20 Check waveform of NIC9270 Check NIC9270 soldering pins 9,12 Check Amp Samsung Electronics...
Page 26
Exploded Views and Parts List 7-2 Main Exploded View and Parts List 7-2-1 Exploded View PCB - FRONT PCB - CD PCB - MAIN PCB - POWER POWER - CORD PCB - DOLBY-PRO Samsung Electronics...
Page 27
-,ABS,-,BLK BASE MAIN AH59-10099A ASSY-PCB SENSOR CMS-300,ASS’Y SENSOR AH59-10100A ASSY-TABLE CHUCK CMS-300,ASS’Y CHUCK AH59-10101A ASSY-PULLEY-MOTOR CMS-300,ASS’Y CHUCK AH66-30086A LEVER-LIFTER ABS HF-380 BLK AH73-10016A RUBBER-CD AJ59-20003F DECK-CDP DECK-CD *CMS-A30NG6 CD SUB PCB TRAY DISC ASS'Y HOOK CD MAIN PCB Samsung Electronics...
Page 52
3RAM ADDRESS LOCK GENERATOR X' TAL XOUT TIMING GENERATOR INTERPOLATE X' TAL C P U MDAT TIMING INTERFACE GENERATOR MCK 38 DIGITAL FILTER (BFS) TRCNT /ISTAT VREFH2 VREFH1 D A C VREFL1 MODE DIGITAL SELECTOR OUTPUT VREFL1 Samsung Electronics 9-11...
Page 53
A/D KEY INPUT4 MULTI JOG IN JOG 21 MULTI JOG IN JOG 22 BGNS NAR EQUALIZER INPUT EQ IN SCOR INTERRUPT SCRO P7 0 CD TRAY SENSE T SENS POWER SENSE SCOR REMOCON INPUT REMO VDVP S 16 9-12 Samsung Electronics...
Page 54
CE 31 NJU3718(OUTPUT) CE CE 23 TC9173(INPUT EXPAND)CE SOL 1 1 DECK SOLENOID SOL 2 2 DECK SOLENOID MICSNS MIC INPUT SENSE CE 21 M65840(KEY CON) LATCH / ST P5 0 DO 2 M65840,65846,MSM6654,TC9173 CLK 2 M65840,M65846,TC9173 Samsung Electronics 9-13...
R/P DECK CD KEY PCB CCDW2 R/P HEAD P/B HEAD CD SUB PCB SCW4 RCW1 SCW1 V-CUT MAIN PCB SCW3 SCW2 FCW2 FAN SUB PCB FCW3 FCW1 PCW1 NCW101 DPCW1 NCW103 POWER PCB CD MAIN PCB POWER PLUG Samsung Electronics 11-1...