Page 1
Service SR6005 / N1SG/N1B/U1B/K1B Manual AV Surround Receiver • For purposes of improvement, specifi cations and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set. Ver.
MARANTZ which it is famous. Parts for your equipment are generally available to our National Marantz Subsidiary or Agent. MARANTZ ORDERING PARTS : Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specifi ed.
SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacture CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
SURR.MODE Service Jigs When you repair the printing board, you can use the following JIG (Extension cable kit). Please order to marantz Offi cial Service Distributor in your region if necessary. 8U-110084S : EXTENSION UNIT KIT : 1 Set (Refer to "JIG FOR SERVICING".)
Page 7
DISASSEMBLY • Disassemble in order of the arrow of the fi gure of following fl ow. • In the case of the re-assembling, assemble it in order of the reverse of the following fl ow. • In the case of the re-assembling, observe "attention of assembling" it. •...
About the photos used for descriptions in the "DISASSEMBLY" section. • The direction from which the photographs used herein were photographed is indicated at "Direction of photograph: ***" at the left of the respective photographs. • Refer to the table below for a description of the direction in which the photos were taken. •...
Page 9
(2) Disconnect the connector wires then remove the screws. CP308 STYLE PIN : Loose Direction of photograph: C Direction of photograph: D (3) Disconnect the connector wires and FFC cable. FFC cable N4401 Please refer to "EXPLODED VIEW" for the disassembly method of each PCB included in FRONT PANEL ASSY.
2. RADIATOR ASSY Proceeding : CABINET TOP FRONT PANEL ASSY RADIATOR ASSY → → (1) Remove the screws. View from bottom (2) Cut the wire clamp bands, then remove the screws. STYLE PIN : Loose Direction of photograph: D Direction of photograph: C...
Page 11
Disconnect the connector wires. RADIATOR ASSY PCB 7CH AMP CP402 CP403 CP405 PCB 7CH AMP CP401 N4905 Please refer to "EXPLODED VIEW" for the disassembly method of each PCB included in RADIATOR ASSY.
4. HDMI UNIT ASSY Proceeding : CABINET TOP HDMI UNIT ASSY → (1) Cut the wire clamp bands, then disconnect the connector wire and FFC cable. CP401 N4610 Direction of photograph: C FFC cable N4401 N4905 HDMI UNIT ASSY CP13A N2004 (2) Remove the screws, then remove the BACK PANEL.
Page 14
(3) Remove the screws and the SUPPORTER PCB. Remove the PCB SIRIUS and the PCB RS232 from the PCB SIDE CNT(Board to board). BRACKET HDMI Board to board SUPPORTER PCB PCB SIRIUS PCB RS232 (4) Disconnect the connector board. Board to board Board to board Board to board PCB HDMI...
Page 15
(6) Remove the screws then disconnect the connector. Direction of photograph: A Connector (7) Disconnect the connector board. PCB SIDE CNT PCB FRONT CNT Board to board PCB PREOUT Board to board PCB AUDIO Please refer to "EXPLODED VIEW" for the disassembly method of each PCB included in HDMI UNIT ASSY.
5. PCB SPK/PCB SMPS Proceeding : CABINET TOP HDMI UNIT ASSY PCB SPK/PCB SMPS → → (1) Remove the screws and SUPPORTER P.C. SUPPORTER P.C. View from bottom (2) Disconnect the connector wire, then remove the screws and SUPPORTER P.C. Direction of SUPPORTER P.C.
Page 17
(3) Disconnect the connector wire, then remove the screws. Remove the PCB SPK and the PCB SMPS from the main unit. CP402 CP403 CP405 (4) Disconnect the connector board. PCB SPK PCB SMPS Board to board...
SPECIAL MODE Special mode setting button b Press the ON/STANDBY button to turn on while pressing both buttons A and B at the same time. Mode Button A Button B Contents Firmware versions such as Main, Sub, DSP are displayed in μcom/DSP Version display mode STATUS RETURN...
Page 19
1. μcom/DSP Version display mode 1.1. Operation specifi cations μcom/DSP version display mode: When started up, the version information is displayed. Starting up: With the "STATUS" and "RETURN" buttons pressed, press the "ON/STANDBY" button to turn the power on. Now, press the "STATUS" button to the display the 2nd item information on the FL Display. 1.2.
Page 20
Q0 H D RADIO SDK/HD RADIO BBP (SR6005 U only): Upper * H D S D K : * * . * * Lower * H D B B P : C 0 0 0 2 . 0 0 0 Q1 U SB Version : Upper U S B...
Page 21
2. Errors checking mode (Displaying the protection history) 2.1. Operation specifi cations Error mode (Displaying the protection history): When started up, the error information is displayed. Starting up: ●All model commonness With the "STATUS" and "CURSOR 0 " buttons pressed, press the "ON/STANDBY" button to turn the power on. The error (protection history display) mode is set.
Page 22
2.3. Clearing the protection history There are two ways to clear the protection history, as described below. (1) Start up the error (protection display) mode, display the error, then press and hold in the "ENTER" button for 3 seconds. Upper P R O T E C T H I S T O R Lower...
3. DUAL BACKUP MEMORY This product has a Dual Backup Memory function. The conventional Backup functions to memorize, in the EEPROM (U5302) in the circuit, a current setting of the moment the main power is turned off so that it can be restored when it is turned ON again.
When you repair the printing board, you can use the following JIG (Extension cable kit). Please order to marantz Offi cial Service. Distributor in your region if necessary. Note: When the connection which is wrong in the JIG (EXTENSION UNIT KIT) is done it becomes cause of damage.
(4) Disconnect the connector board. Board to board PCB VIDEO ASSY (5) Remove the screws then disconnect the connector. Connector (6) Disconnect the connector board. PCB SIDE CNT PCB FRONT CNT Board to board PCB PREOUT Board to board PCB VIDEO...
Page 26
(3) PCB HDMI is detached from the chassis, and it puts it into the state turned inside out. Please pave an insulation sheet that is larger than PCB HDMI under PCB. b Connect the ground point of PCB to the chassis with a ground lead or the like. PCB INPUT Ground lead PCB VIDEO...
Page 27
PCB HDMI Insulation sheet PCB INPUT PCB SIDE CNT Connection table of Board to Board Ref. No. Ref. No. 11 pin SIDE CNT N4908 HDMI 25 pin SIDE CNT N4907 HDMI 19 pin CP105 FRONT CNT N4910 HDMI 17 pin CP106 FRONT CNT N4911...
ABOUT REPLACE THE MICROPROCESSOR WITH A NEW ONE When replaced of the U-PRO (Microprocessor) or the Flash ROM, confi rm contents of the following. After PWB Name Ref. No. Description Remark replaced HDMI U5301 R5F64169DFD SOFTWARE: Main HDMI U5101 W19B160BBT7H SOFTWARE: Main ROM HDMI U5500 R5F3650KNFB...
Page 29
4. Run the DFW Run the "DFW_0004_SR6005_(Rev.1.0.6)" on desktop of PC. 5. Communication check (1) Click the “Check Comm.” button. (2) When connection is good, then you can see the “Communication check OK.” message. (3) If connection is not good, then you can see the “Communication check NG” message. Please confi...
Page 30
6. Download the fi rmware (1) Click the "Load" button. (2) Download the fi rmware from the specifi ed download source to PC. 7. Complete the fi rmware updating (1) Click the “Update” button. (2) When writing of the fi rmware is completed, the power of this unit turns on automatically and you can see the “Update completed”...
Page 31
8. Notice: Please keep the following notice for fi rmware update. (a) Keep the PC environment (b) Avoid the communication cable from the electrical noise source. (e.g. telephone cable, AC line, a fl uorescent light) (c) Don’t remove cable during update. (d) Don’t turn off the power during update.
Page 36
ADJUSTMENT Audio Section Idling Current Required measurement equipment: DC Voltmeter 1. Preparation (1) Avoid direct blow from an air conditioner or an electric fan, and adjust the unit at normal room temperature 15 °C ~ 30 °C (59 °F ~ 86 °F). (2) Presetting •...
TROUBLE SHOOTING 1. POWER 1.1. Power not turn on Power not turn on. When the power turned on, does the ON/STANDBY Is the fuse blown? Refer to 1.2.Fuse is blown. indicator on the front panel fl ashing green? Check for damage Is a DC 5V voltage output in the SMPS B'D Is a DC 5V voltage being...
2. Analog video MONITOR OUT (CVBS) output NG Input CVBS Input Function : SAT COMPONENT To A Not output MONITOR OUT (Component) outpu NG "Video Convert" is set to ON. Input CVBS Input COMPONENT Function : SAT Function : DVD To B...
Page 39
Input CVBS Check power supply voltage. V+5V : N2004-4pin REGULATOR B'D fl aw. V-5V : N2004-1pin Check on set value of each IC. HDMI B'D L4900 : Check I C communication HDMI B'D fl aw. waveforms. L4901 : Check I C communication waveforms.
Page 40
Input CVBS/COMPONENT Check input signal of VIDEO DECODER (U1100). HDMI B'D Check signal detection. V : L4920 HDMI B'D Input CVBS : to A S-Y : L4924 V_L4903 : H(+3.3V) Input COPONENT : to C S-C : L4925 S_L4904 : H(+3.3V) COMPONENT-Y : L4923 COMPONENT_L4902 : H(+3.3V) COMPONENT-Cb : L4922...
Page 41
Input COMPONENT Check of power supply voltage V+5V : N2004-4pin REGULATOR B'D fl aw V-5V : N2004-1pin Check on set value of each IC. HDMI B'D L4900 : Check I C communication HDMI B'D fl aw waveforms. L4901 : Check I C communication waveforms.
Page 42
Check HDMI output setting, referring to the (5) Is the BD/DVD player's HDMI output setting correct? BD/DVD player's operating instructions. (6) When using a marantz BD/DVD player's, is the fl uorescent display tube's "HDMI" indicator lit? If using a non-marantz BD/ DVD player's, proceed to "YES".
Page 43
BD/DVD player is K1001/K1002/K1003) to display's "HDMI" indicator lit? connected. the U1100 is defective. If using a non-marantz BD/ Is communication waveform confi rmed in HDMI DVD player, proceed to connector (K1100/K1101/K1102/K1001/K1002/ "NO". K1003)15pin(DDC_CLK)/16pin(DDC_DATA)?
Page 44
(19) Check power supply. Is 3.3V supplied to L2200/C2230? The power supply circuitry is defective. Is 1.8V supplied to C2242? Is 1.0V supplied to both ends of R2276? (20) Check RESET. The RESET circuitry (U2201 and Is RESET waveform confi rmed in through hole (RESET N)? (If surrounding circuitry ) or U2200 is defective.
Page 45
Check operation of each device. (AMP source : DVR [i/p:OFF] / Video input of player : 480P / Connect the TV.) Check operation of U1002 (ADV3002). (23) Check power supply. The power supply circuitry is defective. Are 5V or 3.3V supplied to U1002 (each power supply pin)? (24) Check RESET.
Page 46
Check operation of U1601. (30) Check power supply. Is 1.2V supplied to C1632? The power supply circuitry is defective. Is 3.3V supplied to C1656? (31) Check RESET. The RESET circuitry (Q1600 and Is RESET waveform confi rmed in N1601 (1pin), when power is surrounding circuitry) or U1601 is defective.
4. AUDIO 4.1. AUDIO CHECK AUDIO OUTPUT : NG INPUT SURROND MODE SOURCE CHECK1 Check ANALOG AUDIO BLOCK. ANALOG 2CH DIRECT ANALOG INPUT SURROND MODE SOURCE CHECK2 Check Digital AUDIO BLOCK. COAX or OPT Legacy(PCM or DolbyDigital or dts…) INPUT SURROND MODE SOURCE CHECK3 Check via AD.
Page 54
4.2. Power AMP (7CH AMP B'D) No sound is output. The protector operates. Is the power transistor open or short circuit? Replace the power transistor. 2SB1647/2SD2560 Is the emitter resistance of the power transistor open? Replace the emitter resistance. 0.47Ω Is the base resistance of the power transistor open? Replace the base resistance.
4.3. Analog audio No sound is output Is the voltage of ±8V supplied to The power supply of ±8V is repaired. AV B'D CP8? Is the audio signal transmitted to The power amplifi er is repaired. AV B'D CN401? Connect the connectors properly. Is the serial data for electronic volume Is the connector correctly connected transmitted to AV B'D CP11?
VIDEO BLOCK DIAGRAM SPDIF/I2S/DSD TO DIGITAL AUDIO SPDIF/I2S/DSD HDMI1 U1601 : XC35S400A-4FGG320C BUS SW FPGA U1801:ADV7511 HDMI2 HDMI OUT HDMI Tx HDMI3 U1100:ADV7840 HDMI IN HDMI Rx U2200:ABT2015 -6dB VIDEO DECODER IP SCALER HDMI4 TO DIGITAL AUDIO I/P SCALER FROM DIGITAL AUDIO U1800:TC74VHC244FT HDMI Tx AUDIO BUS SW FROM RX DIGITAL AUDIO...
Page 60
MAIN +B VCC DIAGRAM S1(AMP +B) MAIN -B NJM7808 A+8.0V (Pre) AZ4580,R2A15220,NJW1194 S2(+8V,-8V) NJM7805 DA+5.0V AK5358/AK4424 NJM7908 A-8.0V (Pre) AZ4580,R2A15220,NJW1194 MAIN TRANS SR6005 PQ120 TRIGGER +12V SR7005 PQ120 TRIGGER +12V NJM2388F 2388F09 : TUNER +9.0V(N/K ver only) S4(VIDEO) NJM7805 A.V+5.0V BU7628,BU4052 PQ033DNA A.V+3.3V...
REG_SIRIUS_COMMON CNT 2/4 SIDE CONNECTOR TO RC-5 TO RC-5 PAGE 8(A4) PAGE 8(A1) OPTION A&B MODEL OPTION_B SR5005 SR6005 SR7005 C125Z2-15P C125Z2-19P OPTION_A IC109 PQ033DNA1ZPH U ONLY CP802 OPEN 10/50 10/50 M3.3V 232IMO IC1A:A 232OMI AZ4580MTR D/MGND TO HD RADIO 10/50 CP801 100N-K...
Page 95
P_A-7V R4000 C4000 D4000 1N4007 100/50 D4001 1N4007 D4002 1N4007 R4354 P_PREZ2L. P_PREZ2L R4001 R4002 C4002 22/50 R4003 R4342 C4001 R4004 R4005 22/50 OPEN OPEN IC4008:A Q4000 Q4001 OPEN OPEN KTC2875B R4010 C4004 R4012 10N-K IC4008:B 470K Q4002 R4013 R4014 OPEN KRA104S C4006...
Page 96
R4154 R4157 R4158 R4155 OPEN OPEN OPEN OPEN R4153 C4065 R4156 C4066 OPEN OPEN R4159 OPEN OPEN R4160 OPEN OPEN Q4052 Q4053 OPEN OPEN R4167 R4168 OPEN OPEN IC4002:A IC4003:A Q4050 Q4051 OPEN Q4054 OPEN Q4055 OPEN OPEN IC4001:A OPEN OPEN R4171 R4173...
Page 97
PAGE 7 (C5) PAGE 7(E5) PAGE 7 (A5) PAGE 5 (B3) N2005 TO FRONT CNT B’D TO FRONT CNT B’D TO FRONT CNT B’D TO REGULATOR B’D OPEN SR7005 SR6005 SR5005 CHIP_J D2001,D2002 KDS160 KDS4148U KDS4148U D2005,D2006 C2006-C2008 C2047,C2060 10/50 22/16 22/16 C2068,C2073...
Page 98
TO S/CVBS K1011 OPEN K1013 RCA-303B1-1 0 COMPONENT VIDEO IN K1001 6P-PIN-JACK K1003 C1001 10/6.3 IN2Y OPEN Z1_YOUT R1049 R1001 R1040 OPEN OUT1 K1001 6P-PIN-JACK K1003 10/6.3 IN2CB C1002 OPEN Z1_CBOUT R1050 R1002 R1041 OPEN K1001 6P-PIN-JACK K1003 10/6.3 IN2CR C1003 OPEN Z1_CROUT...
Page 99
TO COMPONENT TO COMPONENT N3003 OPEN CB-G MONITOR CR-G MONIL1 LINE1 MONIL2 LINE2 MONIL3 LINE3 N3001 OPEN CB-G CR-G LINE1 VIN1L1 LINE2 VIN1L2 LINE3 VIN1L3 N3002 OPEN CB-G JAPAN LINEA LINEB ON CHANNEL CR-G Q3001 LINE1 VIN2L1 ASPECT_H OPEN VIDEO-2 LINE2 VIN2L2 LINE3...
TO DM860 C4230 OPEN C4231 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 OPEN R4232 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OPEN SRCMUTE C4232 SRCDATA SRCDATA OPEN SRC64fs...
Page 114
TO MAIN CPU USB TCC8600 8U-310051(15/20) DIGITAL_UNIT NET3.3V DIGITAL NET1.8V SUPPLY DGND R4410 4.7K R4447 R4411 4.7K U4404 C4455 C4458 AK4424ET C4459 1/10 1/10 JTAG N4400 4.7/6.3 L4402 OPEN BLM21PG221 VSS2 R4431 TCKUSB CVDD MCLKUSB GND_D1 MCLK TDOUSB BCKoUSB BICK VSS1 Aout R4433...
Page 115
L4625 BLM21PG221 L4626 BLM21PG221 L4627 BLM21PG221 D3.3V-1 N4600 OPEN D5.2V D5.2V L4600 L4615 DGN D 20 PVIN BLM21PG221 VOUT OPEN D3.3V-1 DGN D 1.48A 21 PVIN VOUT L4628 11A121 MAINPOWER 22 NC U4601 L4601 L4616 23 NC EX3AV BLM21PG221 OPEN N4610 24 NC NC(SW)
Page 116
TO DIGITAL SUPPLY L5028 OPEN SWM5V L5029 OPEN L5030 OPEN REMOTE3.3V L5031 SWM3.3V OPEN M3.3V L5032 OPEN L5033 OPEN L5034 OPEN L5035 N4907 OPEN 25P-SOCKET(C125Z2) L4927 OPEN D5V(MX) SWM5V(MX) SWM3.3V M3.3V DA+5V D/MGND DA+7V SIR_MO5/RDSDA L5005 OPEN SIR_MO/RDS_DATA DA-7V SIR_MI5/RDSCK L5006 OPEN SIR_MI/RDS_CLK...
Page 119
TO HDMI RX TO VIDEO ENCODER TO HDMI TX TO GUI PLD SCPU5V R5527 4.7 K SCPU3.3V R5528 4.7 K DGND R5529 4.7 K SUBBDOWN SUBBDOWN R5530 4.7 K PLDAERR. PLDAERR. MPLDCLK MPLDCLK MPLDDATA MPLDDATA MPLDCSMAIN MPLDCSMAIN SUBTCK DV_POWER1 SUBTMS CEC_POWER SUBTDI SUBTDO...
WIRING DIAGRAM AC CORD SIRIUS B'D SPK B'D HDMI B'D RS232 B’D TUNER PACK VIDEO B'D FRONT CNT B'D AUDIO IN B'D MAIN TRANS PRE OUT B'D REG_CNT B'D (S2,S4) (S1) REG B'D 2388 7808 7908 7805 7905 7805 2P WIRE(SPK OUT SB) 7CH AMP B'D FRONT B'D (S5,S6)
PARTS LIST OF EXPLODED VIEW zParts for which "nsp" is indicated on this table cannot be supplied. zP.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts. zPart indicated with the mark "...
Page 124
Part Name Remarks Q'ty 963402012440M PANEL FRONT 3067214976030S 963402012420M PANEL FRONT N1B,K1B 3067214976040S 963402012430M PANEL FRONT N1SG 3067214976110S 963421006200M BADGE(MARANTZ) SILVER/GRAY 5630210678000S 963416012230M WINDOW DISPLAY 5077213053000S 943415004150M DOOR FRONT U1B,N1B,K1B 5047210656000S 943415004160M DOOR FRONT N1SG 5047210656100S 943454004170M DOOR MOLD U1B,N1B,K1B...
Page 125
Ref.No. Part No. Part Name Remarks Q'ty PLATE EARTH CHASSIS 4470212006000S SUPPORTER PCB 4070211653000S TAPE ACETATE CLOTH 1220210059050S 00M07BW257010 TOP COVER U1B,N1B,K1B 3007211796000S 943403002040M TOP COVER N1SG 3007211796100S BRACKET HDMI 4010214896100S BRACKET HEATSINK MAIN 4010214906000S CUSHION SIDE 4050213095000S CUSHION SCREW 4050213025000S SHEET CABINET 1210210235000S...
PACKING VIEW N1B,N1SG,K1B model 10 20 N1B,N1SG model N1SG model N1B,N1SG model U1B model N1SG model PARTS LIST OF PACKING & ACCESSORIES zParts for which "nsp" is indicated on this table cannot be supplied. zPart indicated with the mark " ★ " is not illustrated in the exploded view. zThe parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.
Page 127
Q'ty Ref.No. Part No. Part Name Remarks WARRANTY CARD (Canada) 5727041650142S BATTERY DRY G670001R50210S LICENSE LABEL 5507000002940S LICENSE LABEL N1B,N1SG,K1B 5507000004570S SHIPPING LABEL 5507000007500S PE SHEET 6327040059000S 324810004004M SETUP MIC M040000310060S LABEL COLOR N1SG 5507000004600S PAD BOX BACK 6240210730000S 90M-ZC000470R CORD ASSY L068125130010S 963611004880S CORD ASSY L068250100050S...
Page 128
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F64169DFD (HDMI : U5301) (Note 1) IIO0_0 / IIO1_0 / D8 / P1_0 P4_4 / CS3 / A20 / CTS6 / RTS6 / SS6 AN0_7 / D7 / P0_7 P4_5 / CS2 / A21 / CLK6...
Page 129
R5F64169DFD Terminal Functions Pin Name Synbol I/O Type Pullup STBY stop Function 1 P96/(TXD4) SIRIUS RST O/L NC 2 P95/(CLK4) HD RADIO RST/ST IND O/O/I C/C/- O/L HD RADIO control pin /ANALOG TUNER control 3 P94/(CTS4)/TB4IN O/L NC 4 P93/(CTS3)/TB3IN O/L NC 5 P92/TXD3/SDA3 HDRADIO MOHI/TU SDA...
Page 130
Pin Name Synbol I/O Type Pullup STBY stop Function 59 VCC VCC2 60 P131 RST SUB O/L Output for reset of sub-μcom 61 P130 SCPU POWER O/L SUB CPU POWER ON/OFF switch(H:ON) 62 P53/BCLK BCLK O/L External memory access pin(NC) 63 P52/RD O/L External memory access pin(Connection:OE#) 64 P51/(WR1)/BC1...
Pin Name Synbol I/O Type Pullup STBY stop Function 123 P157 ZVOL DATA O/L ZONE VOL(NJW1194) control 124 P156 USB RDY O/L USB(TELECHIPS) control pin 232C CONTROL 125 P155/(RXD6) O/L SUB LOG MODE : For 232C course switch control (SUB LOG MODE) 126 P154/(TXD6) TUNED SW3VPu...
Page 133
R5F3650KNFB Terminal Functions Pu/Pd PURE Pin Name Synbol I/O Type Det P.OFF Function (Int.) (Ext.) STBY 1 P94 VSEL DATA VIDEO PLD control pin 2 P93 DIR CE DIR control pin (LC89058W-VF4A) 3 P92/SOUT3 DIR DIN DIR control pin (LC89058W-VF4A) 4 P91/SIN3 DIR DOUT DA3.3Pu...
Page 134
Pu/Pd PURE Pin Name Synbol I/O Type Det P.OFF Function (Int.) (Ext.) STBY 58 P32 DAC MDI DAC control pin (ASK4358) 59 P31 DAC MC DAC control pin (ASK4358) 60 VCC +3.3V 61 P30 DAC MS DAC control pin (ASK4358) 62 VSS 63 P27 DAC RST...
Page 138
IS42S32200E6TL Terminl Function Pin No. Signal Pin No. Signal Pin No. Signal Pin No. Signal DATA28 DATA27 IOVDD IOVDD ADDR0 SDCAS IOVDD ADDR2 SDRAS DATA26 ADDR1 SDCKE DATA25 ADDR4 SDWE DATA24 ADDR3 TRST DATA23 ADDR5 SDA10 IOVDD DATA22 SDCLK0 DATA21 IOVDD CLK_CFG0 DATA20...
Page 139
LC89058W-E (HDMI : U2805) 35 34 33 32 31 30 29 28 27 26 25 SDIN SLRCK SBCK RDATA XMODE RLRCK DGND LC89058W-E DV DD DV DD DGND GPIO0 RBCK RMCK GPIO1 AGND GPIO2 GPIO3 AV DD RXOUT2 * : Pull-down resistor internal at no selection Pin Functions RXOUT1 RX0-6 input S/PDIF through output pin 1...
Page 140
Pin No. Name Function DGND Digital GND DV DD Digital power supply (3.3V) XMCK Oscillation amplifier clock output pin XOUT Output pin connected to the resonator External clock input pin, connected to the resonator (12.288MHz/24.576MHz) DV DD Digital power supply DGND Digital GND MOUT...
Page 141
ADSP21367KSWZ2A (HDMI : U3200) PIN 1 INDICATOR TOP VIEW (PINS DOWN) ADSP21367KSWZ2A Terminal Function Pin No. Signal Pin No. Signal Pin No. Signal Pin No. Signal DATA28 DATA27 IOVDD IOVDD ADDR0 SDCAS IOVDD ADDR2 SDRAS DATA26 ADDR1 SDCKE DATA25 ADDR4 SDWE DATA24 ADDR3...
W9864G2IH-6 Pin description PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Row address: A0−A10. Column address: A0−A7. 24, 25, 26, 27, 60, 61, 62, Address A0−A10 A10 is sampled during a precharge command to 63, 64, 65, 66 determine if all banks are to be precharged or bank selected by BS0, BS1.
Page 145
EN29LV160BB (HDMI : U3202, U5101) : Bottom boot Sector EN29LV160BT (HDMI : U4400) Top boot Sector BYTE# DQ15/A-1 DQ14 DQ13 Standa rd DQ12 TSOP RESET# DQ11 RY/BY# DQ10 EN29LV160BB/EN29LV160BT Block Diagram RY/BY# DQ0-DQ15 (A-1) Block Protect Switches Erase V oltage Generato r Input/Output Buffers State Control...
Page 153
Signal Name Pin# Type Description – TCC8600 VDDI PWR Digital Power for Internal Core (1.8V) VDDI PWR Digital Power for Internal Core (1.8V) VDDI PWR Digital Power for Internal Core (1.8V) VDDI PWR Digital Power for Internal Core (1.8V) VDDADC PWR Analog Power for ADC (3.3V) VDDPLL PWR Analog &...
Page 154
Pin# Signal Name Type Description – TCC8600 XA[16] / SD_nRAS / ND_ALE External Bus Address Bit [16] / SDRAM RAS signal / ALE for NAND Flash XA[17] / ND_CLE External Bus Address Bit [17] / CLE for NAND Flash XA[18] / DQM[0] External Bus Address Bit [18] / Data I/O Mask 0 XA[19] / DQM[1] External Bus Address Bit [19] / Data I/O Mask 1...
Page 155
Pin# Signal Name Type Description – TCC8600 GPIO_D[17] GPIO_D[17] / I2C SCL GPIO_D[18] / UART1TXD GPIO_D[18] / UART1 TX Data. Internal pull-up resistor enabled at reset. GPIO_D[19] / UART1RXD GPIO_D[19] / UART1 RX Data. Internal pull-up resistor enabled at reset. GND Digital Ground GPIO_D[20] / UART1 RTS Output (active low).
PARTS LIST OF P.C.B. UNIT zParts for which "nsp" is indicated on this table cannot be supplied. zThe parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. U : North America model N : Europe model K : China model...
Page 169
PCB REG_CNT ASS'Y Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP 00D2631289900 IC AZ4580M J121458000020S IC103 00D2630553006 IC NJM7805FA J126780500130S IC104 00D2630554005 IC NJM7905FA J126790500020S IC105 00D2630553006 IC NJM7805FA J126780500130S IC106 00D2630810008 IC NJM7808FA J126780800030S IC107 00D2630503001 IC NJM7908FA J126790800020S IC108 963239010770S...
Page 172
PCB FRONT ASS'Y Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP IC301 00D2631289900 IC AZ4580M J121458000020S z IC304 00D9600195808 IC ICP-N15 J120001500030S IC305 00D2631289900 IC AZ4580M J121458000020S Q300 00D9630226705 TR 2SC KTC1027Y J5021027Y0020S Q302 00D9600285006 TR KRC104S (ND) J522104S00210S Q309 00D9630328302...
PCB HDMI ASS'Y Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP U1001 234810018506S IC,LOGIC TC74VHC4052AFT J040744052080S NOTE : When update Firmware, U1002 236810057606S IC,LOGIC ADV3002BSTZ J040300205510S please confi rm a last U1100 IC ADV7840 J040784005510S version in SDI. Use the service board U1101 IC PQ018ENA1ZPH...
Page 182
Ref. No. Part No. Part Name Remarks Q'ty U4608 234810015507S IC BU4248F J126424800010S U5100 00MHC007805KZ IC TC74VHCT125AFT J040741255580S U5101 963248012480S IC,ROM(MAIN EX),EN29LV160BB-70TIP J005291600050S U5104 234810014504S IC MC14094BDTR2G J040140940020S U5105 00D2623410907 IC TC74VHCT08AFT U1B,N1B,N1SG J040740800090S U5106 234810014504S IC MC14094BDTR2G J040140940020S U5107 234810014504S IC MC14094BDTR2G J040140940020S...
Need help?
Do you have a question about the SR6005/N1SG and is the answer not in the manual?
Questions and answers