Advertisement
Table of Contents
- 1 Table of Contents
- 2 Safety Warnings, AC Requirements, Power Ratings
- 3 Programming
- 4 Error Codes
- 5 Access to Cash Box, Ticket Reset, Meters
- 6 AC Power Connection
- 7 How to Open the Cabinet
- 8 How to Release the Coin Mech Assembly
- 9 Light Bulb Replacement
- 10 How to Remove the Joystick Assembly
- 11 How to Remove the Monitor
- 12 Power Supplies
- 13 I/O Board Connections
- 14 Decal Layout
- 15 Spares
- 16 Warranty
- Download this manual
Advertisement
Table of Contents
Related Manuals for Icegame Harpoon Lagoon
Summary of Contents for Icegame Harpoon Lagoon
- Page 1 OWNERS AND SERVICE MANUAL INNOVATIVE CONCEPTS IN ENTERTAINMENT INC. 10123 MAIN STREET, CLARENCE, NY 14031 SERVICE: 1-716-759-0360 FAX: 1-716-759-0884 E-MAIL: service@icegame.com WEBSITE: www.icegame.com...
-
Page 3: Table Of Contents
Safety Warnings, AC requirements, power ratings Programming Error Codes Access to cash box, ticket reset, meters AC power connection. How to open the cabinet. How to release the coin mech assembly Light Bulb replacement How to remove the joystick assembly How to remove the monitor Power Supplies I/O board connections. -
Page 4: Safety Warnings, Ac Requirements, Power Ratings
SAFETY AND WARNINGS BEFORE YOU BEGIN WARNING: WHEN INSTALLING THIS GAME, A GROUNDED A.C. RECEPTACLE MUST BE USED. FAILURE TO DO SO COULD RESULT IN INJURY TO YOURSELF OR OTHERS. FAIL- URE TO USE A GROUNDED RECEPTACLE COULD ALSO CAUSE IMPROPER GAME OP- ERATION, OR DAMAGE TO THE ELECTRONICS. -
Page 5: Programming
Programming: (Change settings) To enter programming open the Player 1 and 2 lower ticket door and press the “PROG” button. To navigate use the joystick and then press the harpoon but- ton to select. COIN COIN COIN COIN PROG 000000 000000 000000 000000... - Page 6 Programming: The System Utility Structure Audits: General Audits: the income record since very first day of operating day until now. Current Term General Audits: the income record from last time income data clearance. General Game Audits: the game record since very first day of operating until now. Current Term Game Audits: the game record from last time game data clearance.
- Page 7 Programming: The System Utility Structure Operator Adjustments: MODE: Selecting one of these will automatically setup the game with our suggested settings. A=.20 game/.01 ticket value/payout 20%/ 5shots/token/50 bonus B=.25 game/.01 ticket value/payout 40%/5 shots/token/250 bonus C=.50 game/.01 ticket value/payout 40%/5 shots/token/500 bonus D=$1 game/.01 ticket value/payout 40%/10 shots/swipe/1000 bonus E=$1 game/.0045 ticket value/payout 25%/10 shots/swipe/1000 bonus Coins to Play: How many coins you need to start a game.
-
Page 9: Access To Cash Box, Ticket Reset, Meters
How to access the Cash box, ticket reset buttons, and meters. Open the lower ticket door on the player one and player two side of the cabinet. Located in the center of the cabinet is a large cash box, all meters, player 1 ticket reset, and player 2 ticket reset. For players 3 and 4, open the opposite side’s lower coin ticket door for access to the reset but- tons. -
Page 10: Ac Power Connection
Connecting AC Power: Located on the Player 3 and 4 side is the AC power connector. Open the Player 3and 4 ticket door and located to the right of it is the AC power connection. Behind the AC power module is a hole to run the AC power cord to a floor outlet. -
Page 11: How To Open The Cabinet
How to open the cabinet top. Unlock and open both player one and player two control panels. Located at the leftmost and rightmost are two spin knobs. Spin the knobs counter-clockwise until they can be removed. Put aside. Lift the top up. Two cabinet shocks will keep the cabinet top raised for easy access to the electronics. -
Page 12: How To Release The Coin Mech Assembly
How to release the coin mech assembly. Unlock and open the control panel you wish to remove the coin mech. Located on the right is a release level. Push the level to the right and slide the mech holder assembly straight back and out. -
Page 13: How To Remove The Joystick Assembly
How to remove the joystick assembly. Open the control panel where the joystick is located that you wish to service. Remove the joystick shaft by removing the E-Z clip located at the bottom of the joystick. Put aside the switch activator and E-Z clip. -
Page 14: How To Remove The Monitor
How to remove the monitor. You will need a second person to assist you in removing the monitor. Begin by following the steps in the section “How to open the cabinet top”. Once the cabinet top is opened disconnect the upper wire harnesses. Remove the screws shown below. Carefully lift the upper assembly off the cabinet with two people and lay the assembly on its top side. - Page 15 Remove the 10 keep nuts holding the monitor to the upper assembly. The monitor can be lifted out. When replacing the monitor be sure to install a new gasket between the glass and the cabi- net. Monitor Gasket...
-
Page 16: Power Supplies
Power Supplies: There are three different power supplies used. Two are identical supplying 12 volts of DC voltage at 10 amps each while the third powers the monitor at 24 Volts of DC power. To access these sup- plies, follow the directions from “How to open the cabinet top.” Ice part: IA2010 Ice part: IA2010 Ice part: MON42/47PS... -
Page 17: I/O Board Connections
PLAYER 1 PLAYER 3 PLAYER 2 PLAYER 4... -
Page 20: Spares
- SPARE PARTS - MECHANICAL JC1051 Hydraulic shock HL1009-P802 Cash box HL3010 Knob HL3011 Corner Cover ELECTRONICS HH5005CC ticket dispenser E022007 Speaker HL2014BL Blue joystick HL2014CL Clear Joystick HL2014PK Pink Joystick HL2014YW Yellow Joystick IA2010 12 volt power supply MON47EST 47”... -
Page 22: Warranty
(including labor) that is performed by such a distribu- tor. Innovative Concepts in Entertainment 10123 Main St. Clarence, NY 14031 Phone #: (716) - 759 – 0360 Fax #: (716) – 759 – 0884 www.icegame.com...
Need help?
Do you have a question about the Harpoon Lagoon and is the answer not in the manual?
Questions and answers