Table of Contents
Advertisement
INSTALLATION GUIDE
DB3
2017 Volkswagen Golf GTI (Smart Key). 403.VW06 1.41
Designed by Installers for Installers
© 2017 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
Advertisement
Table of Contents
Related Manuals for Directed Electronics DB3
Summary of Contents for Directed Electronics DB3
- Page 1 INSTALLATION GUIDE 2017 Volkswagen Golf GTI (Smart Key). 403.VW06 1.41 Designed by Installers for Installers © 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.
-
Page 2: Table Of Contents
Contents Introduction Vehicle function compatibilities Pre-installation and application warnings Wiring diagram Locating components in the vehicle Immobilizer interface with OEM immobilizer receiver Vehicle connections Connecting the module Module programming LED diagnostics and troubleshooting Soft reset Hard reset Feature programming Feature and option list Limited one year consumer warranty Quick reference guide... - Page 3 Warning! Safety first The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.
-
Page 4: Introduction
Introduction DB3 is an all-in-one door lock and override module. Warning! This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to “Connecting the module” for more information. Vehicle function compatibilities This section lists all the functions compatible with this vehicle for the installation illustrated in this guide. -
Page 5: Pre-Installation And Application Warnings
Pre-installation and application warnings Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations. T-Harness Keys required for Keys required for compatible programming operation Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic... -
Page 6: Vescm: Vehicle Electrical
Wiring diagram Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( XKD2D65 HS CAN 2 High: Orange/Green, pin 16 HS CAN 2 Low:Orange/Brown, pin 15 HS CAN 1 High: Orange/Red, pin 6 Diagnostic Electronic Steering... -
Page 7: Locating Components In The Vehicle
Locating components in the vehicle VESCM - Vehicle Electrical System Control Module at Driver Side under dash, above Driver Kick Panel ESCLCM - Electronic Steering Column Lock Control Module at Steering Column 403.VW06 1.41 2017 Volkswagen Golf GTI (Smart Key) ©... -
Page 8: Immobilizer Interface With Oem Immobilizer Receiver
Method 1: Immobilizer interface with OEM immobilizer receiver (PTS) Common Relay 2: Yellow/Red: 11 NO Relay 2: Brown/Red: 12 4-6 loops Immobilizer Receiver Note: OEM immobilizer receiver is located on the underside of the steering column, where the ignition switch would normally be. Remove battery from OEM Remote Control Note:... - Page 9 Method 3: Key wrap for Push-to-Start (PTS) using OEM immobilizer ring NC Relay 2: Orange/Red: 10 Common Relay 2: Yellow/Red: 11 NO Relay 2: Brown/Red: 12 4-6 loops Immobilizer Receiver Note: OEM immobilizer receiver is located on the underside of the steering column, where the ignition switch would normally be.
-
Page 10: Vehicle Connections
Vehicle connections The connection information listed below is specific to the 2017 Volkswagen Golf GTI (Smart Key). Refer to “Pre-installation and application warnings” for a list of important notes. Data 14-pin blue connector (H1) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color... - Page 11 Input 10-pin black connector (H3) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Ref. H3/1 Green (-) W2W Only - Lock Input Remote Starter H3/2 Blue (-) W2W Only - Unlock Input Remote Starter H3/3 Red/White (-) W2W Only - Trunk Input Remote Starter H3/4 White/Violet...
-
Page 12: Connecting The Module
Connecting the module Important! Make all the required connections to the vehicle, as described in this guide, and double check to ensure everything is correct prior to moving onto programming. Warning! To take advantage of advanced features, you must use DirectLink 4.5 (and higher) or the Directechs Mobile application. Flashing a module using your computer: 1. -
Page 13: Module Programming
Module programming Refer to “LED diagnostics and troubleshooting” for more information and for troubleshooting purposes. Wait until the LED turns ON solid red. Press on the Unlock button on the OEM remote. Press the Push-to-Start (PTS) button once to turn the ignition ON. The LED flashes orange, then flashes green. -
Page 14: Led Diagnostics And Troubleshooting
LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module Programming Description Troubleshooting Make sure the D2D harness is connected and that 12 Volt is present between the red and black Module has no power. - Page 15 External Module Synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 Active Ground When Running (Status) Description Troubleshooting Ground When Running (Status) command The module has initialized the remote start sequence.
-
Page 16: Soft Reset
Soft reset A module reset will only erase the steps perfomed in “Module programming”. The firmware and settings flashed to the module will not be affected. D2D installation Connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness. -
Page 17: Feature Programming
Feature programming To enter feature programming routine: 1. Turn the ignition ON, then OFF. 2. Within 5 seconds, press and hold the programming button until the LED turns ON orange (after 3 seconds). 3. Release the Programming button. 4. The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate the current option of feature 1 (e.g. -
Page 18: Feature And Option List
Feature and option list It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page at www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page. -
Page 19: Limited One Year Consumer Warranty
Limited one year consumer warranty For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under... -
Page 20: Quick Reference Guide
Quick Reference Guide Sending commands to your vehicle Pit stop/idle mode Whether you want to remote start the engine, lock/unlock the doors or pop the trunk, Stop the vehicle in a safe parking spot and put the gear in there are 3 possible ways you can send commands to your vehicle, using the: gear in Park (P). - Page 21 List of available commands Notes Note that the information below is for many Viper, Clifford, Python, Avital, Automate, Autostart and AstroStart models. Icons and commands may differ depending on the model and options purchased. Refer to your authorized installation center for more specific information.
Need help?
Do you have a question about the DB3 and is the answer not in the manual?
Questions and answers