Table of Contents
Advertisement
Quick Links
AXI 02 AT • Setup Guide
This guide provides basic instructions for an experienced technician to install the AXI 02 AT Dante Audio Interface. The Extron
AXI 02 AT is a compact audio interface that receives two channels from a Dante
without a Dante interface. It features two line level analog outputs on captive screw connectors with a mirrored two-channel
S/PDIF output on a coaxial RCA connector. Device configuration is performed using Extron DSP Configurator Software. Full
Dante configuration is available using Dante Controller. For additional information, specifications, and the user guide, see the
AXI 02 AT product page at www.extron.com.
Disconnect Power and Mount the AXI 02 AT
Disconnect power from the AXI 02 AT and turn off all devices that will be connected to it. The AXI 02 AT is housed in an
eighth-rack width, 4.42-inch (133 mm) deep, 1U-high enclosure that can be mounted on a rack shelf, secured with the included
ZipClip 100
mounting clip, or secured to rack rails with tie wraps. Select a suitable mounting location, then choose an
™
appropriate mounting option.
Rear Panel Connections
OUTPUTS
1
2
A
Figure 1.
AXI 02 AT Rear Panel Connections
Analog Audio Outputs — Use 6-pole, 3.5 mm captive screw connectors to connect two balanced or unbalanced mono
A
line level devices. Balanced or unbalanced stereo devices can also be connected using 3-pole or 6-pole captive screw
connectors.
Tip
Ring
Sleeve
Tip
Ring
Sleeve
Balanced Output
6-pole Audio OUTPUT Wiring
Figure 2.
Audio Output Wiring
ATTENTION :
•
For unbalanced audio outputs, connect the sleeves to the ground contact. DO NOT connect the sleeves to the
negative (-) contacts.
•
Pour l'audio asymétrique, connectez les manchons au contact au sol. NE PAS connecter les manchons aux
contacts négatifs (–).
NOTES:
•
Balanced or unbalanced stereo sources can be connected with 6-pole connectors.
•
When using a 5-pole CSR adapter, connect it so the far left plug is inserted into the far left jack of the 6-pole output.
S/PDIF Audio Output — Two S/PDIF output channels mirror the analog outputs on a coaxial RCA connector. Attenuation
B
applied to the analog outputs does not affect the S/PDIF output.
S/PDIF
1/2
Analog Audio Outputs
A
B
Tip
NO Ground Here
Sleeve
Tip
NO Ground Here
Sleeve
Unbalanced Output
audio network, providing connectivity to devices
®
S/PDIF Audio Output
B
Tip
NO Ground Here
Ring
Sleeve
Balanced Output
3-pole Audio OUTPUT Wiring
Tip
Sleeve
Unbalanced Output
1
Advertisement
Table of Contents
Related Manuals for Extron electronics AXI 02 AT
Summary of Contents for Extron electronics AXI 02 AT
- Page 1 Disconnect Power and Mount the AXI 02 AT Disconnect power from the AXI 02 AT and turn off all devices that will be connected to it. The AXI 02 AT is housed in an eighth-rack width, 4.42-inch (133 mm) deep, 1U-high enclosure that can be mounted on a rack shelf, secured with the included ZipClip 100...
- Page 2 USB Config Port — Connect a computer to this USB Mini-B port for device configuration and firmware updates. AT (PoE) Port — This RJ-45 port is used to connect the AXI 02 AT to a Dante network. The AT (PoE) port supports digital audio transport (AT), communication with the Dante network, communication with DSP Configurator for device configuration, and power over Ethernet (PoE).
- Page 3 Renaming the AXI 02 AT The AXI 02 AT default device name consists of the device model and the last six characters of the device MAC address. When multiple devices are on the network with default device names, identifying a specific device is difficult. To avoid confusion when multiple devices are on a network, Extron strongly recommends renaming each device with a unique and meaningful identifier.
- Page 4 Creating a Physical Dante Network A physical network is required to share Dante audio channels among Dante-enabled devices like the AXI 02 AT. Other devices capable of sending and receiving audio over a Dante network must be on the same physical network in order to communicate via Dante (see figure 4 below for an example of a physical Dante Network).
- Page 5 The AXI 02 AT analog outputs are listed as Dante receivers because they receive digital audio from the Dante network. Additionally, audio received by the analog outputs is mirrored over the S/PDIF output. The AXI 02 AT does not transmit signal onto the Dante network, and therefore does not have transmit channels.
Need help?
Do you have a question about the AXI 02 AT and is the answer not in the manual?
Questions and answers