Step 3 - Basic Programming - Rockwell Automation SMC FLEX Quick Start Manual

Step 3 - Basic Programming

The SMC-Flex controller can be programmed with the built-in keypad and LCD display or with an optional
Bulletin 20-HIM-xx LCD human interface module.
Menu Structure Hierarchy
Power Up and Status Display
Stopped
---
0.0
0.0
0.0
Monitoring
Metering
SMC Option
Volts Phase A-B
Motor Connection
Volts Phase B-C
Line Voltage
Volts Phase C-A
Starting Mode
Current Phase A
Ramp Time
Current Phase B
Initial Torque
Current Phase C
Cur Limit Lvl
Watt Meter
Kickstart Time
Kilowatt Hours
Kickstart Level
Elapsed Time
Stop Input
Meter Reset
Option 1 Input
Power Factor
Option 2 Input
Mtr Thermal Usage
Stop Mode
Stop Time
Overload Class
Service Factor
Motor FLC
Overload Reset
Aux1 Config
Aux2 Config
Aux3 Config
Aux4 Config
Parameter Mgt
Amps
Volt
%MTU
Set Up
Basic Overload
Overload Class
Service Factor
Motor FLC
Overload Reset
Overload A Lvl
Parameter Mgmt
Underload
Underload F Lvl
Underload F Dly
Underload A Lvl
Underload A Dly
Parameter Mgmt
Undervoltage
Undervoltage F Lvl
Undervoltage F Dly
Undervoltage A Lvl
Undervoltage A Dly
Parameter Mgmt
Overvoltage
Overvoltage F Lvl
Overvoltage F Dly
Overvoltage A Lvl
Overvoltage A Dly
Parameter Mgmt
Unbalance
Unbalance F Lvl
Unbalance F Dly
Unbalance A Lvl
Unbalance A Dly
Parameter Mgmt
Main Menu
Parameters
Diagnostics
Preferences
Memory
Storage
Log In *
(* - Only Active when a password is used)
Motor Protection
Jam
Jam F Lvl
Jam F Dly
Jam A Lvl
Jam A Dly
Parameter Mgmt
Stall
Stall Delay
Parameter Mgmt
Ground Fault
Gnd Flt Enable
Gnd Flt Lvl
Gnd Flt Dly
Gnd Flt Inh Time
Gnd Flt A Enable
Gnd Flt A Lvl
Gnd Flt A Dly
Parameter Mgmt
PTC
PTC Enable
Parameter Mgmt
Phase Reversal
Phase Reversal
Parameter Mgmt
Restart
Starts Per Hour
Restart Attempts
Restart Delay
Parameter Mgmt
See File Structure Below for
additional details
Alarms
Faults
Device Revision
Change Password
User Dspl Line
User Dspl Time
User Dspl Video
Reset User Display
Reset to Defaults
Enter Password
Utility
Communications
Language
Comm Masks
Logic Mask Language
Parameter Mgmt Parameter Mgmt
Data Links Motor Data
Data In A1
Motor FLC
Data In A2
Motor ID
Data In B1
Parameter Mgmt
Data In B2
Data In C1
Data In C2
Data In D1
Data In D2
Data Out A1
Data Out A2
Data Out B1
Data Out B2
Data Out C1
Data Out C2
Data Out D1
Data Out D2
Parameter Mgmt
Note:
• Depending on the SMC option, additional
parameters may appear in some menus
• The external HIM has similar programming
operation to the built-in HIM, however some
differences do exist.
• The built-in HIM can not be used to program
other DPI devices (i.e. Device Select)
SMC™ Flex Quick Start 11
Linear List
Linear List
All Parameters