1. Manuals
  2. Brands
  3. Nureva Manuals
  4. Projector
  5. SPAN
  6. Installation manual

Nureva SPAN Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

NUREVA™ SPAN™ SYSTEM

INSTALLATION GUIDE

February 2017

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SPAN and is the answer not in the manual?

Questions and answers

Related Manuals for Nureva SPAN

Summary of Contents for Nureva SPAN

  • Page 1: Installation Guide

    NUREVA™ SPAN™ SYSTEM INSTALLATION GUIDE February 2017...
  • Page 2 Important SAFETY WARNINGS Prior to installing this product, ensure you fully read and understand the installation instructions. Failure to do so could result in personal injury or property damage. You are responsible for ensuring all components are properly assembled and installed using the instructions provided. Keep this information sheet and related product manuals for future reference.
  • Page 3 Important SAFETY WARNINGS NOTICE: This projector is a Class 2 laser device that conforms to IEC 60825-1: 2007 and CFR 1040.10 and 1040.11. Except for deviations to Laser Notice No.50 dated June 24 2007. FCC NOTICE This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules.

  • Page 4: Table Of Contents

    3. Install the hardware 4. Connect the hardware 5. Initial adjustment of the projected image(s) 6. Install the surfaces 7. Download Span wall software and touch driver 8. Set up touch 9. Final adjustment of the projected image(s) 10. Launch Span software 11.

  • Page 5: What's In The Box

    What’s in the box BOX 1: NPSi-1 or NSPi1080-1 A Interactive projector B Touch module C Projector remote control D Stylus x 2 E Power cable F USB cable 16.4' (5 m) G Touch module power cord H Alignment card I Touch module bracket J Screws to attach touch module to bracket...

  • Page 6: You Must Supply

    You must supply To install the system successfully you need to provide the following items. Go through these checklists and ensure everything is on hand before you begin to install the system. CABLES AND CONNECTORS Must meet the following specifications: •...

  • Page 7: Determine The Installation Location

    Determine the installation location Ensure the area you select to install your system meets the following requirements and recommendations. SPACE REQUIREMENTS Locate the installation drawing for your system’s configuration in the appendix of this 102” (260 cm) guide for the detailed space MIN.

  • Page 8: Install The Hardware Brackets

    Install the hardware brackets Install the wall mount plate(s) 2.1.1 Download the installation drawing for your system's configuration from nureva-span.uservoice.com Measure and mark the system 2.1.2 centerline. Refer to installation measurement 1 on your installation drawing. 2.1.3 From the centerline, measure from the floor to the top of the wall mount plate holes.
  • Page 9 2.1.4 Measure from the spot you marked on the centerline to the top left wall mount plate hole. Mark the remaining wall plate holes. Refer to installation measurement 3 on your installation drawing. 2.1.5 Ensure the wall mount plate is level.
  • Page 10 Ensure the bracket is level. 2.2.2 Attach the touch module bracket to the wall using the #4 screws and anchors. Repeat with any remaining brackets. February 2017...

  • Page 11: Install The Hardware

    Install the hardware Install the wall mount boom and projector 3.1.1 Attach the projector plate(s) with four of the screws provided. Position the plate so the angled edge is closest to the projector vent. 3.1.2 Adjust the boom length to •...
  • Page 12 3.1.4 Attach the wall mount boom to the wall mount plate. Attach the projector to the boom with four of the screws p X4 p X4 p X4 p X4 provided. Repeat with any remaining booms and projectors. 3.1.5 Attach the cables from the mount to the back of the projector.
  • Page 13 Install the touch module Remove the touch module 3.2.1 cover. Attach the unit to the bracket using the two screws provided. Ensure the unit is seated securely against the wall. k k k k If you are installing a NOTE: Da-Lite screen, follow the instructions provided with...
  • Page 14 Install the NAM image alignment module 3.3.1 If you are using the mounting brackets, attach them to the NAM using the screws provided on the sides of the NAM. 3.3.2 If you are mounting the NAM(s), use the #6 screws and appropriate anchors a minimum of 5”...

  • Page 15: Connect The Hardware

    Connect the hardware Ensure your IPV4 Ethernet port is enabled correctly. If you are hardwiring your PC to your network, you may need a USB-Ethernet adapter to connect the second Ethernet cable to your PC. HDMI in Ethernet HDMI out (to PC) (to PC) (to projector)

  • Page 16: Initial Adjustment Of The Projected Image(S)

    Initial adjustment of the projected image(s) 5.1.1 Power on the NAM, projector and PC. 5.1.2 Use the adjustment options on the mount to straighten IMAGE SIZE IMAGE SIZE IMAGE SIZE IMAGE SIZE and square off the projected IMAGE IMAGE IMAGE IMAGE ADJUSTMENT ADJUSTMENT...
  • Page 17 5.1.3 For double and triple configurations, ensure each projected image has at least 1" (2.5 cm) of overlap. For corner, edge and surround configurations, reference your installation drawing for the gap required between each projected image. 5.1.4 Use the slider on the side of the projector to bring the image into focus.

  • Page 18: Install The Surfaces

    6. Install the surface(s) Follow the installation guide for your selected surface. To install the WhisperTek™ surface, follow the WhisperTek surface installation guide. Go to https://nureva-span.uservoice.com/ Search WhisperTek To install the Da-Lite screen, follow the Da-Lite screen installation guide. Go to: https://nureva-span.uservoice.com/...

  • Page 19: Download Span Wall Software And Touch Driver

    Download Span wall software and touch driver 7.1.1 Use the wireless keyboard and mouse to navigate to the Internet. Download and install Span wall software from the Download section at nureva-span.uservoice.com. Download and install the 7.1.2 touch driver from the Download section at nureva-span.uservoice.com.

  • Page 20: Set Up Touch

    Set up touch Set up the touch module laser curtain 8.1.1 Press the adjustment button to turn the touch module to Adjustment mode on/off ADJUSTMENT ON/OFF ADJUSTMENT ON/OFF adjustment mode. This will emit two visible laser beams from the bottom of the unit. The LED light will blink red and blue when the touch module is in adjustment...
  • Page 21 8.1.4 Rotate the black knob counterclockwise to move the laser beams downward until they appear on the floor or surface below the projected image. 8.1.5 Fold the laser alignment cards along the dotted line. ADJUSTMENT ON/OFF ADJUSTMENT ON/OFF Hold the alignment cards against the wall to check if the laser falls within the grey zone.
  • Page 22 8.1.7 Slide the card diagonally toward the touch module to check if the dot stays within the grey zone all the way to the top. Repeat this process on the other beam. Ensure both beams are an equal distance from the wall. 8.1.8 Press the adjustment button to switch off adjustment...
  • Page 23 8.2.2 Select Touch Area Setting and choose Auto from the drop-down menu. The screen will flash a series of dots. Click OK. 8.2.3 Select Calibration from the menu and choose Auto from the drop-down menu. The screen will flash a series of dots. Click OK. Repeat the touch area setting steps on any remaining PCs.

  • Page 24: Final Adjustment Of The Projected Image(S)

    Final adjustment of the projected image(s) Align the image(s) 9.1.1 Launch Span center from the icon located on the desktop task bar on each of the projected images. 9.1.2 Select Image Alignment. The Span center allows you to use touch to shrink the images until they are square and aligned.
  • Page 25 1. Select your system’s PC/ 9.1.4 projector configuration. : If you have 1 projector and NOTE 1 PC, select 2PCs - 2 Projectors 2. Ensure the IP addresses are 192.168.0.11 and 192.168.0.12 3. Ensure the correct Projector Model (Resolution) is set. NPSi-1 projectors 1920 x 720 NPSi1080-1 projectors...
  • Page 26 Calibrate touch 9.2.1 Click Done once you have completed the image alignment. Select Touch Calibration. The screen will flash a series of dots. Repeat on any remaining displays. 9.2.2 Attach the plastic covers to the wall mount plate, wall mount boom and touch module.

  • Page 27: Launch Span Software

    Launch Span software 10.1 Launch the wall software 10.1.1 On each projected image, launch Span wall software from the icon on the desktop. 10.1.2 For configurations with multiple displays, log in to the software on one of the displays. This will automatically log you in on the other projected images.

  • Page 28: Troubleshooting

    Update display setup. Linking displays only NOTE: needs to be done on the initial log in. The system saves the display settings and applies them to all subsequent log ins. Troubleshooting For troubleshooting, please see our Customer support portal. https://nureva-span.uservoice.com February 2017...

Table of Contents

Save PDF