ThyssenKrupp orion Installation Manual
  1. Manuals
  2. Brands
  3. ThyssenKrupp Manuals
  4. Lifting Systems
  5. orion
  6. Installation manual
ThyssenKrupp orion Installation Manual

ThyssenKrupp orion Installation Manual

Vertical platform lift
Hide thumbs Also See for orion:
Table of Contents

Advertisement

Quick Links

See also: User Manual
Orion - Gulliver Vertical Platform Lift
Optional Installation Manual
INS-OPT-EN-07
ThyssenKrupp Encasa

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the orion and is the answer not in the manual?

Questions and answers

Related Manuals for ThyssenKrupp orion

Summary of Contents for ThyssenKrupp orion

  • Page 1 Orion - Gulliver Vertical Platform Lift Optional Installation Manual INS-OPT-EN-07 ThyssenKrupp Encasa...

  • Page 3: Table Of Contents

    01/09/2014 Orion Optional Installation Manual Contents 'EVO' door-opener ___________________________________________________________ 2     1.1. Preliminary inspection ____________________________________________________ 2     1.2. Assembly of the mechanical components _____________________________________ 2     1.3.   Electrical connections _____________________________________________________ 4   1.4. Setting the boards _______________________________________________________ 4  ...

  • Page 4: Evo' Door-Opener

    01/09/2014 Orion Optional Installation Manual 'EVO' door-opener 1.1. Preliminary inspection  Check that the door is in good condition.  Check that the door movement is uniform and that the hinges are not too loose.  Check that the door is plumb and in line with the horizontal upright to which the sliding guide must be fixed.
  • Page 5 01/09/2014 Orion Optional Installation Manual  If the elevator is with casing to be installed internally, pierce the beam above the door and use the spacer as shown in figure 4.  If the elevator is with casing to be installed externally, attach the three Spacer adhesive thicknesses behind the roof covering.

  • Page 6: Electrical Connections

    01/09/2014 Orion Optional Installation Manual  Fix the door-opener with 6 M6x40 screws, 6 M6 nuts and 6 washers.  At the same time, fix the casing roof covering over the holes that remain outside the door-opener, with 2 M6x35-TS-PEI screws.

  • Page 7: Operating Anomalies

    01/09/2014 Orion Optional Installation Manual 1.6. Operating anomalies In the event of anomalies, test the door-opener installed on the door behaving in an anomalous fashion separately, as follows: 1. Bridge pins 1 and 2 on the actuator board and check door closure.

  • Page 8: Seat

    01/09/2014 Orion Optional Installation Manual Seat  Position the seat in the position shown in figure 13 and create two 8 mm diameter holes using the frame as a template. Figure 13  Connect the seat support corners (see figure 14).

  • Page 9: Return To Low Floor Procedure

    01/09/2014 Orion Optional Installation Manual ELECTRICAL CONNECTION DIAGRAM RP - NP  When on, the red LED positioned above the resistance signals device functioning. Warning! Before enabling, ensure that you have filled the tank with hydraulic oil. Do not enable the resistance dry.

  • Page 10: Alarm System Helpy

    01/09/2014 Orion Optional Installation Manual Alarm system HELPY Press the button on the telephone keypad corresponding to the symbol shown. It indicates any phone digit: this symbol is used in the programming description generally to indicate entries by the operator.
  • Page 11 01/09/2014 Orion Optional Installation Manual A Terminal board B JP8 Jumper (not to be removed or moved) C Internal power connector D Connectors for optional relay board E Serial socket for connection to lift CPU F Reset button G RJ11 connector for local telephone...

  • Page 12: Connections

    01/09/2014 Orion Optional Installation Manual 4.1. Connections Ensure that the jumper JP8 (see Fig.17) is in position 1-2 or towards the outside (manufacturer's settings). Figure 17 – Jumper JP8 position Connect the telephone line to the LTI terminal board on the optional board (See Fig.16 detail N).

  • Page 13: Verifying Installation And Speed Programming

    01/09/2014 Orion Optional Installation Manual 4.1.1. Verifying installation and speed programming Programming the telephone line Raise the local telephone. Key in  0 # from the local telephone to enter into programming. After having heard 3 short tones, key in 6 6 0 .

  • Page 14: Autodialer" Telephone Combiner - Programming

    01/09/2014 Orion Optional Installation Manual  Press 0 to go to hands free or wait 30 seconds.  Press 1. After approximately 2 seconds, press 9 to definitively cancel the call. ATTENTION! If the alarm procedure cannot be interrupted (e.g. the programmed telephone number is wrong), you will need to raise the local telephone.

  • Page 15: Basic Programming

    01/09/2014 Orion Optional Installation Manual After programming, to make the settings effective, you will need to exit the programming status. To this end, use the same procedure as to access programming:  Raise the local telephone. You will hear the signal inviting you to make a selection.
  • Page 16 01/09/2014 Orion Optional Installation Manual “1” Call Centre with Ademco Contact ID protocol; “2” Normal telephone utility; “3” Call Centre with Esse-ti protocol; “4” Call Centre with CLI mode.  Enter the telephone number to be called (maximum 20 digits).
  • Page 17 01/09/2014 Orion Optional Installation Manual To listen to the message  Raise the micro telephone   Key in 0 # from the local telephone to enter into programming.  Press 7 2 0 1. You will hear the message.

  • Page 18: Advanced Programming

    01/09/2014 Orion Optional Installation Manual  Enter:  0 to disable the flat battery alarm.  1 to enable the flat battery alarm. Example: to enable the flat battery alarm, key in 5 2 1.   Hang up and key in 0 # from the local telephone to exit from programming.
  • Page 19 01/09/2014 Orion Optional Installation Manual  Connection in the event of switchboard telephone rather than directly to the landline.  Enabling the 'Diagnostics' technological alarm. Recording / re-listening to the courtesy message The courtesy message is that re-produced by the hands...
  • Page 20 01/09/2014 Orion Optional Installation Manual  Hang up and key in  0 # from the local telephone to exit from programming Note: when connected to a telephone switchboard, you will need to enter the prefix for the switchboard landline, prior to the programmed numbers.
  • Page 21 01/09/2014 Orion Optional Installation Manual...
  • Page 23 Pag.4   Foro per il pressocavo Hole for cable clamp Apertura per l’labero della frizione Opening for clutch shaft Pag.4 Montante cerniera Hinge upright riferimento posizionamento guida per porta dx Position guide reference for RH door riferimento posizionamento guida per porta sx Position guide reference for LH door Pag.7 Morsettiera di ingresso del quadro principale...

This manual is also suitable for:

Gulliver

Table of Contents

Save PDF