Related Manuals for Brunswick Contender Apollo
Summary of Contents for Brunswick Contender Apollo
- Page 1 Apollo POCKET BILLIARD TABLE INSTALLATION MANUAL www.brunswick-billiards.com SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104 SEPTEMBER 2004 51-904874-001...
- Page 2 NOTE: Please use the instructions in this manual to assemble the tables shown below. Illustrations may be different depending on the table being assembled. Also note that careful handling of all components will assure damage-free assembly. PAGE 2 BRUNSWICK INSTALLATION MANUAL...
- Page 3 “U” channel facing down. Attach the stretchers so that the foot of the leg is to the outside. Secure the stretcher to the leg using 5/16-18 x 1” flange button socket cap screws and 5/16 flatwasher. FIGURE ONE FIGURE TWO BRUNSWICK INSTALLATION MANUAL PAGE 3...
- Page 4 1/4-20 hex nuts on top. FIGURE 3 FIGURE FOUR Step #3: With the base frame loosely assembled place squarely on top of the four leg plates, between the “L” brackets. FIGURE FOUR PAGE 4 BRUNSWICK INSTALLATION MANUAL...
- Page 5 “L” brackets. FIGURE 5 FIGURE SIX Step #6: Loosely attach the side sills to the “L” brackets using 3/8-16 x 2-1/4” hex head bolts, 3/8 flat washers and 3/8-16 hex nut. FIGURE 6 BRUNSWICK INSTALLATION MANUAL PAGE 5...
- Page 6 The levelers should be rotated out atleast 1/4” to allow for further leveling when the slate is attached. NOTE: Try to leave atleast 5’ between the outer edge of the baseframe to any wall. PAGE 6 BRUNSWICK INSTALLATION MANUAL...
- Page 7 Step #9: Slate joints can now be filled with Rock Hard putty or wax. Lightly sand or scrape across the joints after grouting. BRUNSWICK INSTALLATION MANUAL PAGE 7...
- Page 8 This is important as this will provide cushioning from ball impact and the bed cloth will last much longer. Step #11: Clean top of slate thoroughly with a damp cloth before applying the bed cloth. FIGURE THREE PAGE 8 BRUNSWICK INSTALLATION MANUAL...
- Page 9 Step 1. Step #6: Stretch the cloth from #1 to #3 and press into position. Step #7: Stretch the cloth #3 to #4, pulling from #1 and #2. Press into place. FIGURE THREE BRUNSWICK INSTALLATION MANUAL PAGE 9...
- Page 10 #5 and toward the side pocket from #2 and tack or staple at #7. Step #10: Repeat Step 7, stretching from #6 and toward the side pocket from #4 and tack or staple at #8. FIGURE THREE PAGE 10 BRUNSWICK INSTALLATION MANUAL...
- Page 11 NOTE: Occasionally cloth will stretch, leaving wrinkles at the pockets. To retighten, remove apron, one end rail and one side rail. Pull cloth taut, and retack or restaple FIGURE SEVEN along the open end and side to restore original tightness. BRUNSWICK INSTALLATION MANUAL PAGE 11...
- Page 12 Step #6: Turn rail over and at corner pockets fold the cloth over the mitred edge as shown, stretching tightly and working out any wrinkles as you staple three places in area shown. FIGURE FIVE PAGE 12 BRUNSWICK INSTALLATION MANUAL...
- Page 13 Step #12: Hold the small fold in place with thumb and forefinger and firmly hold it down over facing. Then staple at rear of facing and at bottom of rail as shown. Step #13: Trim excess cloth as required. FIGURE TEN BRUNSWICK INSTALLATION MANUAL PAGE 13...
- Page 14 #8 x 1/2". Step #6: Into each rail, thread three, 3/8-16 threaded machine studs. Tighten securely then back off 1/2 turn. FIGURE TWO PAGE 14 BRUNSWICK INSTALLATION MANUAL FIGURE THRE...
- Page 15 “bow” while turning as the strain may cause the rail to crack at the ends. Step #5: Align the eighteen machine studs with the eighteen clearance holes through the slate, and lower assembly onto the slate. FIGURE TWO BRUNSWICK INSTALLATION MANUAL PAGE 15...
- Page 16 Step #9: Thoroughly brush the area on which the bed spots are to be applied. Position the bed spot and firmly roll a ball over the spot to achieve good adhesion. NOTE: Bed spots are self adhesive. FIGURE FIVE PAGE 16 BRUNSWICK INSTALLATION MANUAL...
Need help?
Do you have a question about the Contender Apollo and is the answer not in the manual?
Questions and answers