Winterhalter UC series Manual
Hide thumbs
Also See for UC series:
- Operating instructions manual (49 pages) ,
- Manual (10 pages) ,
- Short operating instructions (2 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Winterhalter UC series
Summary of Contents for Winterhalter UC series
- Page 1 Under counter UC series Commissioning regulation...
-
Page 2: Table Of Contents
Table of contents Commissioning regulation for Winterhalter UC Series Table of contents Table of contents ..........................2 About these instructions ........................2 Explanation of symbols used ........................ 2 Safety notes............................3 Requirements ............................3 Checking the electrical installation ....................3 Connection diagram for mains connection cable ................ -
Page 3: Safety Notes
− The machine is still live unless the on-site mains disconnector or the built-in mains disconnector is switched off. − Installation may only be performed by a service technician trained and authorised by Winterhalter. − When using chemicals, adhere to the safety notes and recommended dosages printed on the packaging. -
Page 4: Connection Diagram For Mains Connection Cable
Connection diagram for mains connection cable Basic information: The UC series dishwashing machines can be connected to both 3-phase alternating current and 1-phase alternating current. The machine contains a connection diagram which indicates the terminals to which the mains connection cable has to be connected. The boiler heating element is already connected. However, bridges still need to be set so that the power supply's fuse rating is not exceeded. -
Page 5: Connection Diagram For Belgium (230V/3/Pe) And Malaysia
Connection diagram for mains connection cable 6.2 Connection diagram for Belgium (230V/3/PE) and Malaysia 6.3 Connection diagram for Australia... -
Page 6: Connection Diagram For Japan
Checking the plumbing installation 6.4 Connection diagram for Japan Checking the plumbing installation Check the following: − Has the plumbing installation been performed according to the information on the rating plate (permitted water pressure, permitted water inlet temperature)? − Has the supplied dirt trap been installed on the water stop cock? −... -
Page 7: Checking The Filter System
Open the screw cap on the salt container and top up the salt container to the brim with fresh water. Place the funnel in the filling opening on the salt container and gradually add 3 bags of Winterhalter spe- cial salt (=1.5 kg). -
Page 8: Rinse Aid And Detergent
Wear protective clothing, protective gloves and protective goggles when handling chemicals. Warning Only use products which are suitable for commercial dishwashing machines. Such products are marked accordingly. We recommend using products developed by Winterhalter. These products are specially adapted for Winterhalter dishwashing machines. Caution Do not mix different detergent products as this could result in crystallisation and consequently cause irreparable damage to the detergent dosing device. -
Page 9: Programming The Machine
Programming the machine 11 Programming the machine The UC series dishwashing machines are designed to be suitable for different applications. The Winterhalter service technician does not program the machine's control unit for use of the dishwashing machine as a “special machine” for a specific application until it is installed. Alternatively, the dishwashing machine is sup- plied from the factory already programmed for a certain application, but can be reprogrammed at any time. -
Page 10: Selecting The Language And Entering The Basic Parameter Set
Programming the machine 11.1 Selecting the language and entering the basic parameter set Close the machine door. Open the on-site water stop cock. Switch on the on-site mains disconnector. Screen 24 with the language selection appears on the touchscreen. You access other languages u- sing the scroll button Press the language in which you want the subsequent text to appear. -
Page 11: Changing Further Parameters
Programming the machine When the basic parameter set is saved, a default setting is made for all parameters. Therefore, they only have to be changed if the machine complies with one or more of the following conditions. Operation with TE / TV demineralisation system P 503 = 0001 Operation with built-in softener P 503 = 0002... -
Page 12: Machine Without Water Treatment
Programming the machine 11.3 Machine without water treatment On machine which are operated without water treatment, the symbol opposite can be displayed at regular intervals as a reminder that descaling has to be performed. Descaling reminder? Screen 50 Descaling reminder in operating hrs. -
Page 13: Machine With Integrated Softener
Programming the machine 11.5 Machine with integrated softener On machine which are operated with an integrated softener, the total hardness of the raw water has to be entered in °dH (German degree of hardness). The following formulae may be used to convert other degrees of hardness into °dH: −... -
Page 14: Date, Time, ° Celsius / ° Fahrenheit; Date Of Installation
Programming the machine 11.7 Date, time, ° Celsius / ° Fahrenheit; date of installation Screen 23 To set the date (1): Press button (1). Enter the current date using the numeric keypad (8). Format: YYYY-MM-DD (year-month-day) The entered date is checked to determine whether it is a valid date. Your entry will not be accepted if it is implausible. -
Page 15: Summary Of The Changed Parameters
Transfer all the changed parameter values to the overview with the basic parameters. Exit the menu by pressing button (2). Screen 01 appears. 12 Switching on the machine Welcome! Winterhalter wishes you a pleasant day. Screen 02 Screen 01 If the screen is darkened:... -
Page 16: Venting The Integrated Dosing Equipment
If the dosing equipment is integrated into the machine during installation or is installed externally, you must adhere to the respective device documents for the particular dosing equipment and the operating instructions for the UC series. Screen 04 Press button (1). -
Page 17: Manual Entries
Manual entries 14 Manual entries The following working steps are only necessary if the machine has already been programmed in the factory and the menu-driven installation procedure (chapter 11.1 to 11.8) has not been completed. 14.1 Date, time, ° Celsius / ° Fahrenheit; date of installation Press the button “i ”... -
Page 18: Water Treatment
Manual entries To enter the machine number (5): Press button (5). Enter the machine number using the numeric keypad (8). To set the date of installation (6): Press button (6). Enter the current date using the numeric keypad (8). Format: YYYY-MM-DD (year-month-day) The entered date is checked to determine whether it is a valid date. -
Page 19: Machine Without Water Treatment
Manual entries 14.2.2 Machine without water treatment On machine which are operated without water treatment, the symbol opposite can be displayed at regular intervals as a reminder that descaling has to be performed. Use parameter P 597 to set a value in hours (= operating hours). The symbol shown above appears after the set time has elapsed. -
Page 20: Changing Further Parameters
Manual entries 14.3 Changing further parameters The machine's control unit can be adjusted within certain limits to the customer's needs by setting certain parameters accordingly. A complete overview of all parameters and the menus for the service technician are included in the service instructions. The standard washing programmes can be changed in the simplest manner using the “Sinner circle”... -
Page 21: Instructing Personnel
Explain the descaling programme for machines without water treatment. Point out that descaler must not be mixed with active chlorinated detergent (production of chlorine gas). Explain what daily maintenance is required. Winterhalter Gastronom GmbH; Gewerbliche Spülsysteme Tettnanger Strasse 72, 88074 Meckenbeuren, Germany Tel: +49 (0) 7542 402-0; Fax +49 (0) 7542 402-187...
Need help?
Do you have a question about the UC series and is the answer not in the manual?
Questions and answers