Advertisement
D-V4300D
11. PANEL FACILITIES
-ACIN
Cormec1 this to a
wall
socket 1120 or 220-240V AC.
50/60Hz)
using
a
triple-conductor
power
cord. A suitable
cord should be obtained from your dealer.
VOLTAGE SELECTOR 1120V/220·240V ACI
Used to
change
the operating
volte9e
of
the
pla
yer.
Set the
selector
to the
mains voltage
in your
area.
VIDEO OUT terminals
(RCA
jack,
BNC
Jacki
These
terminal!.
ere connected
to the
v
ideo input jack
of the
TV
monitor.
The Hme signals ere
output
from
both
terminals.
RGB terminal
10-sye
9 pin)
Used
for
connection to the
RGB
monitor.
1,
ONO
9 8.7 6
2.
ONO
3.
RED
4.
GREEN
&.
BLUE
1
2
3 4
S
O.
NC
7. NC
6.
Compo11t1 1ync.
9.
PALJNTSC
IPAL=H/NTSC=LI
131
EXT SYNC termination
selector
This
switch is used
for
selecting whether the signal input to
EXT
SYNC IN is given 75
Q
termination
within the player lON
position),
or looped through IOFF
position)
.
EXT SYNC IN, OUT
terminals
(BNC
Jacks)
IN
:
Connects to the sync generator in
the
event that
the main unit is
operated in e11ternal sync
mode.
O.(OUTI
:
Can be
connected to EXT
SYNC
IN terminal
of
se·
cond
player.
NOTE:
• Set the
EXT
SYNC
termination
selector in
eccordance with
the conditions
of
use.
AUDIO OUT
terminals
(RCA Jacks)
For connection to a
stereo amplifier (LO, AUX etc.)
EFM OUT
terminal
(S
pin
DIN)
To
connect en
LO-ROM
adaptor.
1.
PAL/NTSC
(PAL:H/NTSCsLI
2.
GNO
3.
Audio
L (ON
=
H/OFF=U
4
.
EFM
5
.
Audio
R
lON=H/OFF
-
LI
'~:
RS-232C INTERFACE
CONNECTOR
ID-SUB
15 plnl
2
Used
for serial interface
connection
to e
computer
or con-
troller.
PARK Indicator
•
Indicates that
the pickup is II the
park position
(extreme
inner
circumfereneel and
in
standby
status.
•
Blinks
during
opening/closing operation of
the
disc
table,
and goes off
when operiinglctosing
is
completed.
• Lights
up
when
a
disce11ists in
the
player.
PAL
and
NTSC
indicators
•
Displays
the
type of disc
being
played
back
during disc
playback.
• In standby status. indicates
the sening
of the
PAL/NTSC
SELECT
bunon.
REMOTE SENSOR
window
When using
the
optional
remote control unit
in the
w
ireless
format,
the
infrared
commands
from
the unit
are
received
here.
Receiving unit
tor
infrared
signals
when
using
the optional
bar
code reeder
UC-V
1048C in th
e wireless mode.
KEY LOCK
Indicator
Lit
when the KEY
LOCK command
is entered
from the
e)l
tern-
al
control
unit.
W
hen
this
indicator
is lit, entries
are
not
accepted
from
opera
-
tion
buttons
other
then
the
pow er switch.
Also, entries ere
not
accepted from
the
operation
bunons
of the separately
sol
d
remo1econtrol
unit
.
132
PLAY
indicator
Lights during
pteyback.
Blink
when
the disc
rotation
stan
s/stops.
SEARCH
indicator
Lights
during e)lecution of
search.
PLAY(~)
button
PAL/NTSC SELECT
button
Chooses
whether
PAL signal or NTSC
signal
shall be output
as
the squelch
signal aher the power
has been turned
on.
This
button
can
be
manipulated
while the
disc
is not being
played
back.
The
PAL
indicator
or
the NTSC indicator
lights
up
to indicate
the selection
status.
NOTE:
This bunon is
invalid
during
disc
p
leybeck.
OPEN/CLOSE
(a
I
~
I
button
This
button
is
used 10 open and close the disc
table.
Saning a
disc
on the
disc
table !hen pressing 1his button
retracts
1he
disc
table into
the
player.
Pressing
this
button
during player
stops
play.
When pressed again, the
table
will
be
e)ltended
from the
player.
Advertisement
