Related Manuals for Hafco HM-32
Summary of Contents for Hafco HM-32
- Page 1 Page 1 Instructions Manual for HM-32 (K012) 07/02/2018 MILL DRILL OPERATION MANUAL Model. HM-32 Edition No :MD001 Date of Issue : 01/17...
- Page 2 Page 2 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL MACHINE DETAILS MACHINE MILL DRILL MODEL NO. HM-32 SERIAL NO. DATE OF MANF. Distributed by www.machineryhouse.co.nz Note: This manual is only for your reference. Owing to the continuous improvement of the machine, changes may be made at any time without obligation or notice.
-
Page 3: Table Of Contents
Page 3 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL C O N T E N T S: 1. GENERAL MACHINE INFORMATION 1.1 Specifications..............4 1.2 Standard Equipment............4 1.3 Identification..............5 1.4 Electrical Controls............6 1.5 Accessories..............6 2. SAFETY 2.1 Safety Requirements............7 2.2 Power Supply..............10 2.3 Site Preparation............10... -
Page 4: Specifications
Page 4 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL 1.1. SPECIFICATIONS..Table Size 820 x 240mm Column Type Ø 115mm Spindle Taper Longitudinal Travel (X-Axis) 540mm Cross Travel (Y-Axis) 190mm Vertical Travel (Z-Axis) 410mm Type of Slides Dovetail Spindle to Table... -
Page 5: Identification
Page 5 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL 1.3 IDENTIFICATION Fig. 1 Fig. 2 A. ON/OFF Buttons K. Cross Travel Lock B. Drawbar & Cap L. Longitudinal Travel Lock C. Belt Cover M. Table Stop D. Motor N. Cross Travel Handwheel E. -
Page 6: Electrical Controls
Page 6 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL 1.4 ELECTRICAL CONTROLS A1. Emergency Stop A2. Emergency Stop Release A3. Forward/Reverse Switch A4. Start Button A5. Stop Button 1.5 ACCESSORIES 1. Machine Vice 2. Face Mill and Arbour 3. Drill Chuck 4. -
Page 7: Safety
Page 7 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL 2. SAFETY 2.1 SAFETY REQUIREMENTS WEARING PROPER APPAREL. Do not OWNER’S MANUAL. Read and understand this wear clothing, or jewelry that can become owner’s manual before using the machine. entangled in moving parts. Always tie back or cover long hair. - Page 8 Page 8 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL 2.1 SAFETY REQUIREMENTS Cont. WARNING MAINTAIN POWER CORDS. When FORCING MACHINERY. Do not force the disconnecting machines from power, grab machine. It will do the job safer and better at and pull the plug and not the cord.
- Page 9 Page 9 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL 2.1 SAFETY REQUIREMENTS Cont. UNDERSTANDING CONTROLS. Make sure SPINDLE SPEEDS. Select the spindle speed you understand the use and operation of all that is appropriate for the type of work and controls.
-
Page 10: Power Supply
Page 10 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL 2.2 POWER SUPPLY Availability Before installing the machine, consider the availability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this machine, a new circuit must be installed. -
Page 11: Lifting Instructions
Before you place your machine on the cabinet, it is recommend you M0015 consider the following options. When mounting on the optional cabinet consider using Hafco M0015 machine mounts to make it easy for leveling and eliminates vibration. Bolting the machine also to the floor prevents tipping or shifting and reduces vibration that may occur during operation, resulting in a machine that runs slightly quieter and feels more solid. -
Page 12: Mounting To A Workbench
If the machine is to be mounted to the cabinet and then mounted to the floor, and if the use of Hafco Machine Mounts M0015 are being used, use a precision level and adjust the machine mounts until the machine table is level. -
Page 13: Operation & Test Run
Page 13 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL 4. OPERATION & TEST RUN Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation. The test run consists of checking the following: 1) The motor powers up and runs in the correct direction 2) the stop button safety feature works correctly. -
Page 14: Changing Spindle Speeds
07/02/2018 OPERATION MANUAL 4.2 CHANGING SPINDLE SPEEDS The Model HM-32 is capable of twelve different speed settings. Different types of cuts and materials require varying speeds. For the correct speed refer to publication such as Hafco L341 Fitting and Machining To change spindle speeds: 1. -
Page 15: Basic Controls
Page 15 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL 4.3 BASIC CONTROLS Listed below are the machines basic controls and their description. The operator should be familiar with these items and the terminology. Depth Stop: When set this stops the spindle travel at a predetermined depth. -
Page 16: Maintainance
Page 16 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL 5. MAINTAINANCE 5.1 TROUBLESHOOTING SYMPTOMS POSSIBLE CAUSE POSSIBLE SOLUTION Machine does not start 1. Wall fuse or circuit breaker 1. Reset circuit breaker or change fuse has been tripped 2. Plug faulty or wired incorrectly 2. -
Page 17: Lubrication
Page 17 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL 5.2 LUBRICATION Points requiring periodic lubrication are: A. Column. A light film of oil ( ISO VG-68) will smooth action and prevent rust and corrosion. B. Column Rack. Lubricate every 90 days with a general purpose industrial NLGI 2 grease C. -
Page 18: Optional Accessories
07/02/2018 OPERATION MANUAL 5.3 OPTIONAL ACCESSORIES The HM-32 Mill Drill is supplied with some basic tooling. Below is a list of quality tooling that may be needed to enhance the scope of the machine. Order Code C933B TOOLMASTER C922B—3MT Chuck & Collet Set An affordable quick change collet system with ultra precision. -
Page 19: Electrical Circuit Diagram
Page 19 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL A. ELECTRICAL DIAGRAM... -
Page 20: Spare Parts
Page 20 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL SPARE PARTS SECTION The following section covers the spare parts diagrams and lists that were current at the time this manual was originally printed. Due to continuous improvements of the machine, changes may be made at any time without notification. - Page 21 Page 21 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL B. HEAD BODY PARTS LIST...
- Page 22 Page 22 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL B. HEAD BODY PARTS LIST NAME NAME NAME cover board motor up cover fixed nut round bolt adjustable rod bolt trademark motor rack screw rivet washer referral-board stop lump V-belt...
- Page 23 Page 23 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL C. TABLE COLUMN PARTS LIST...
- Page 24 Page 24 Instructions Manual for HM-32 (K012) 07/02/2018 OPERATION MANUAL C. TABLE COLUMN PARTS LIST NAME NAME Screw Ball Bearing washer Screw Column Lid Graduatiot Plate Link Dial Clutch Column screw Rack Hand Wheel Bolt Turn Handle Washer Screw Base...
-
Page 25: Risk Assessment Sheets
Page 25 Instructions Manual for HM-32 (K012) 07/02/2018 General Machinery Safety Instructions Machinery House requires you to read this entire Manual before using this machine. 1. Read the entire Manual before starting 14. Use correct amperage extension cords. machinery. Machinery may cause serious injury if Undersized extension cords overheat and lose not correctly used. - Page 26 Page 26 Instructions Manual for HM-32 (K012) 07/02/2018 Lathe-Mill-Drill Safety Instructions Machinery House requires you to read this entire Manual before using this machine. 1. Maintenance. 11. Stopping the spindle. Make sure the Lathe-Mill-Drill is Do not slow or stop the turned off and disconnect from the main power spindle by using you hand.
- Page 27 Page 27 Instructions Manual for HM-32 (K012) 07/02/2018...
Need help?
Do you have a question about the HM-32 and is the answer not in the manual?
Questions and answers