3-5 Software Upgrade 4. Trouble shooting 4-1 First Checklist for Troubleshooting 4-2 Checkpoints by Error Mode 5. Exploded View and Parts List 5-1 LE40M71B Exploded View 5-2 LE40M71B Parts List 6. Electrical Parts List 6-1 LE40M71B Parts List 7. Block Diagram 8.
Page 4
Contents 10. Operating Instructions and Installation 10-1 10-1 Front 10-1 10-2 Connection Panel 10-2 10-3 Remote Control 10-4 10-4 Installing the Stand 10-5 10-5 Installing the Wall Mount Kit 10-5 11. Disassembly and Reassembly 11-1 11-1 Disassembly 11-1 11-2 Reassembly 11-5 12.
Page 5
Samsung Electronics Co.,Ltd. - This Service Manual is a property of 416, Maetan-3Dong, Yeongtong-Gu, Suwon City, Samsung Electronics Co., Ltd. Gyeonggi-Do, Korea, 443-742 Any unauthorized use of Manual can be Printed in Korea punished under applicable International P/N : BN82-00144A-00 and/or domestic law.
1 Precautions 1 Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 Safety Precautions 1-1-1 Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC Power Jack before servicing.
1 Precautions 1-2 Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1 Precautions 1-4 Installation Precautions 1. For safety reasons, more than two people are 6. Keep the antenna far away from any high-voltage required for carrying the product. cables and install it firmly. Contact with the high- voltage cable or the antenna falling over may 2.
Excellent Compatibility. SD/MMC/CF/MD/MS/MSPRO/XD/SM Smooth Motion Driver - No ghosting, No Smearing Edge in image powered by Smooth Motion Driver Engine of Samsung LCD TV Wide Color Gamut - More natural and vivid picture quality by WCG (127%) High Dynamic Contrast...
3 Alignments and Adjustments 3 Alignments and Adjustments 3-1 Service Instruction 1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync. 2. Use the specified test equipment or its equivalent. 3.
3 Alignments and Adjustments 3-2 How to Access Service Mode 3-2-1 Entering Factory Mode 1. To enter "Service Mode" Press the remote -control keys in this sequence : - If you do not have Factory remote - control INFO MENU MU TE - If you have Factory remote - control - The buttons are active in the service mode.
3 Alignments and Adjustments 3-4 Service Adjustment 3-4-1 White Balance - Calibration If picture color is wrong, do calibration first. Equipment : CA210, Patten : chess pattern Execute calibration in Factory Mode Source AV : PAL composite, Component : 1280*720/60Hz PC : 1024*768/60Hz ( chess patten ) 3-4-2 White Balance - Adjustment...
Page 20
3 Alignments and Adjustments 3-4-3 Conditions for Measurement 1. On the basis of toshiba ABL pattern : High Light level (57 IRE) - INPUT SIGNAL GENERATOR : MSPG-925LTH * Mode 2 : 744X484@60 Hz 6 : 1280X720@60 Hz NO 21 : 1024X768@60 Hz * Pattern NO 36 : 16 Color Pattern NO 16 : Toshiba ABL Pattern 2.
Page 21
3 Alignments and Adjustments d) Adjust the high light. (Refer to table 1, 2 in adjustment position by mode) - Adjust red gain ('x') and blue gain ('y') to the color coordinates. * Do not adjust the green gain and sub-contrast (Y) data. Picture 4-3 Toshiba ABL Pattern High light Measurement point...
3 Alignments and Adjustments 3-5 Software Upgrade 3-5-1 How to Update Flash ROM 1. Installthe Flash Downloader ConnectSet(Service Jack)and Jig Cable to execute Program Update. 2. Flash Downloader program update -Before Turning on the set,Click "connect"which is under of OSD Screen! -Turn on the Set.
4 Troubleshooting 4 Troubleshooting 4-1 First Checklist for Troubleshooting 1. Check the various cable connections first. - Check to see if there is a burnt or damaged cable. - Check to see if there is a disconnected cable connection or a connection is too loose. - Check to see if the cables are connected according to the connection diagram.
4 Troubleshooting 4-2 Checkpoints by Error Mode 4-2-1 No Power LAMP off, power indicator Check a connection a power cable. LED blue color? Does proper DC 12V Change a Assy PCB Power. appear at CM801? Does proper DC A3.3V, Check a IC1008, IC1004. A5V appear at Change a main PCB ass'y.
Page 26
Change a main PCB ass'y. RA6005_120Hz, RA6009_120Hz, RA6016_120Hz, RA6018_120Hz)? Does the digital data appear Check IC6003,4 at the out of L6001~12? Change a main PCB ass'y. Check a LVDS cable? Please, Call to Samsung Co. LTD. Replace a lcd panel?
Page 27
4 Troubleshooting WAVEFORMS R,G,B Output Signal of IC500...
Page 28
Change a main PCB ass'y. RA6005_120Hz, RA6009_120Hz, RA6016_120Hz, RA6018_120Hz)? Does the digital data appear Check IC6003,4 at the out of L6001~12? Change a main PCB ass'y. Check a LVDS cable? Please, Call to Samsung Co. LTD. Replace a lcd panel?
Page 29
4 Troubleshooting Digital Output Data of IC500 Signal of HDMI(Data)
Page 30
Change a main PCB ass'y. RA6005_120Hz, RA6009_120Hz, RA6016_120Hz, RA6018_120Hz)? Does the digital data appear Check IC6003,4 at the out of L6001~12? Change a main PCB ass'y. Check a LVDS cable? Please, Call to Samsung Co. LTD. Replace a lcd panel?
Page 32
Change a main PCB ass'y. RA6005_120Hz, RA6009_120Hz, RA6016_120Hz, RA6018_120Hz)? Does the digital data appear Check IC6003,4 at the out of L6001~12? Change a main PCB ass'y. Check a LVDS cable? Please, Call to Samsung Co. LTD. Replace a lcd panel?
Page 33
4 Troubleshooting WAVEFORMS CVBS Output Signal 4-10...
Page 34
Change a main PCB ass'y. RA6005_120Hz, RA6009_120Hz, RA6016_120Hz, RA6018_120Hz)? Does the digital data appear Check IC6003,4 at the out of L6001~12? Change a main PCB ass'y. Check a LVDS cable? Please, Call to Samsung Co. LTD. Replace a lcd panel? 4-11...
Page 35
4 Troubleshooting WAVEFORMS Digital Output Data of IC500 Analog Signal(Y,C) to IC500 4-12...
Page 36
4 Troubleshooting 4-2-7 No Sound Connect a sound cable. Picture is display, no sound. control a volume. Does the signal appear at Pin #10, #16(CH1_L, R Sound) Check a connection harness and and Pin #3, #9 headphone jack / Side AV. (CH2_L, R Sound) of IC1015? Check the DC 12V...
Page 37
4 Troubleshooting WAVEFORMS The Signal are Inputed to IC1015 DC +12V 4-14...
5 Exploded View & Parts List 5 Exploded View and Parts List - You can search for updated part codes through ITSELF web site. URL : http://itself.sec.samsung.co.kr/ 5-1 LE40M71B Exploded View M0013 T0447 M0014 M0215 T0003 T0175 T0175 M0013...
6 Electrical Parts List 6 Electrical Parts List You can search for updated part codes through ITSELF web site. URL : http://itself.sec.samsung.co.kr/ 6-1 LE40M71B Parts List Level Loc. No. Code No. Description & Specification Q'ty SA/SNA LE40M71BX/XEC LE40M71B,Q56A/40M70-GMS,40,LCD-TV,SPAIN M0001 BN90-00935A ASSY COVER FRONT;40M70,EO,ABS+PMMA,HB,BK...
8 Wiring Diagrams 8-3 PIN characteristic CN800 - Main Board power supply NAME SW GND GND GND GND GND B12VS B12VS GND POWER NAME GND GND GND B12V B12V B12V B12V GND Function Define - B12V B12V_CHN, B9V, B8V, B5V_VCCT - B5V B33V, B5V_VCCA, B3.3VD, B2.5V_VDD, B1.8VD, PX_VD1.8, PX_VA1.8, PX_VL1.8, B1.2VD - B12VS...
Page 75
8 Wiring Diagrams CN221 - Front control NAME SDA-T SCL-T GND GND IDENT HP-L HP-R INPUT1 INPUT1 INPUT2 Function Define - A5V Front control board poewr supply - KEY INPUT1,2 Key control, from the memu, change up/down Etc. - IR Remote control signal - LED Control the timing and stand by LED color...
Page 78
8 Wiring Diagrams CN801 - AC Input NAME Live Netural VOLTAGE Functing Define - Refer to : AC Input CN801 - Main Board power supply NAME 13V GND 5.4V 5.4V 5.4V GND GND GND GND ST7V PWR Functing Define - ST7V Stand-By Output - PWR Power On/Off Control - Refer to : CN801 function define CNM804 - Panel control...
Page 79
8 Wiring Diagrams CN802 - Inverter power supply NAME 24V GND GND GND GND Functing Define - AMLCD Panel Inverter Power - 24V LAMP INVERTER Voltage - B/L Brightness sensor power - A_D ANA_DIMMING - P_D PWM_DIMMING CN803 - Inverter power supply NAME 24V GND GND GND GND...
Page 81
8 Wiring Diagrams CN801 - AC Input NAME Live Netural VOLTAGE Functing Define - Refer to : AC Input CN801 - Main Board power supply NAME 13V GND 5.4V 5.4V 5.4V GND GND GND GND ST7V PWR Functing Define - ST7V Stand-By Output - PWR Power On/Off Control - Refer to : CN801 function define CNM804 - Panel control...
Page 82
8 Wiring Diagrams CN803 - Inverter power supply NAME 24V GND GND GND GND Functing Define - AMLCD Panel Inverter Power - 24V LAMP INVERTER Voltage - B/L Brightness sensor power - A_D ANA_DIMMING - P_D PWM_DIMMING CN804 - Inverter power supply NAME 24V GND GND GND GND...
10 Operating Instructions and Installation 10 Operating Instructions and Installation 10-1 Front - The product colour and shape may vary depending on the model. 1. SOURCE 5. SPEAKERS Toggles between all the available input sources (TV, Ext.1 , Ext.2, AV, S-Video, Component, PC, HDMI1, (POWER) HDMI2).
10 Operating Instructions and Installation 10-2 Connection Panel - Whenever you connect an external device to your TV, make sure that power on the unit is turned off. - When connecting an external device, match the colour of the connection terminal to the cable. 10-2...
Page 94
10 Operating Instructions and Installation Connecting an Aerial or Cable Television Network To view television channels correctly, a signal must be received by the set from one of the following sources: - An outdoor aerial / A cable television network / A satellite network Connecting HDMI/DVI - Supports connections between HDMI-connection-enabled AV devices (Set-Top Boxes, DVD players, AV receivers and digital TVs).
10 Operating Instructions and Installation 10-3 Remote Control 1. Selects a target device to be controlled by the Samsung remote control (TV, DVD, STB, CABLE, VCR) 2. Television Standby button 3. Number buttons for direct channel access 4. One/Two-digit channel selection 5.
For detailed information on installing the wall mount, see the instructions provided with the Wall Mount items. Contact a technician for assistance when installing the wall mounted bracket. Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the TV on your own.
Page 97
10 Operating Instructions and Installation Memo 10-6...
11 Disassembly and Reassembly 11 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the TFT-LCD WARNING : This monitor contains electrostatically sensitive devices. Use caution when handling these components. 11-1 Disassembly Cautions : 1. Disconnect the monitor from the power source before disassembly. 2.
Page 99
11 Disassembly and Reassembly Description Picture Description 2. Remove screws from the rear-cover and lift up the rear-cover. 3. Disconnet cables from the main and power boards Remove screws from the side AV jack. 11-2...
Page 100
11 Disassembly and Reassembly Description Picture Description 4. Remove screws from the boards and stand BRKT. 5. Lift up the speakers. Remove screws from the BRKT. 11-3...
Page 101
11 Disassembly and Reassembly Description Picture Description 6. Lift up the Panel and remove screws. 7. Lift up the panel BRKT. 11-4...
13 Circuit Descriptions 13 Circuit Descriptions 13-1 Block description Mosel consists of three main blocks 1. Main board : Video signal processing 2. IP board : Power supply & Inverter 3. T-con board : LCD Panel control 13-1...
Page 107
13 Circuit Descriptions I I NVERTER SMPS Mosel consists of three main blocks 1. Main board : Video signal processing 2. SMPS : Power supply 3. T-con board : LCD Panel control 13-2...
14 Reference Infomation 14 Reference Infomation 14-1 Technical Terms - TFT-LCD - Auto Configuration(Auto adjustment) (Thin film Transistor Liquid Crystal Display) This is an algorithm to adjust monitor to optimum ADC(Analog to Digital Converter) condition by pushing one key. This is a circuit that converts from analog signal to digital signals.
Page 111
14 Reference Infomation - T.M.D.S - Interlace and Non-Interlace Methods (Transition minimized Differential Signaling) Showing the horizontal lines of the screen from the a kind of transmission method for Digital. top to the bottom in order is called the Non- It can be used from Video card to Main PBA.
Page 112
Enables high picture quality and clear sound channel to obtain the best viewing conditions. The throughout the country regardless of the location of Samsung LCD TV has both automatic and manual the viewer. channel fine-tuning features to enable the viewer to adjust their desired settings.
Page 114
14 Reference Infomation 14-2-2 Component 14-2-3 S-Video Separate RCA Green Pb (Cb) RCA Blue Pr (Cr) RCA Red Audio L 14-2-5 D-SUB RCA White Separate Audio R RCA Red Green Blue 14-2-4 A/V GND Red GND Green GND Blue RCA Yellow CVBS DDC Input power(+5V) Audio L...
Page 115
14 Reference Infomation 14-2-7 Scart 1 Signal Signal Audio output R Audio input R Video GND (RGB red) Audio output L Audio common GND RGB red input Video GND (RGB blue) Fast Blanking signal (RGB switching) Audio input L Video output GND RGB blue input Video input GND Switching voltage...
14 Reference Infomation 14-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer- generated video signals. 14-3-1 LCD Panel Mode1 mode 14-7...
Need help?
Do you have a question about the LE40M71B and is the answer not in the manual?
Questions and answers