Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for HPRT HT100
Summary of Contents for HPRT HT100
- Page 1 HT100/HT130 User Manual Label Printer User Manual HT100 HT130 Xiamen Hanin Electronic Technology Co.,Ltd ADD: Room 305A,Angye Building,Pioneering Park, Torch High-tech Zone,Xiamen,China. Tel.: +86-(0)592-5885993 Fax: +86-(0)592-5885992 Web: www.hprt.com Rev.1.2...
-
Page 2: Table Of Contents
HT100/HT130 User Manual Contents MANUAL INFORMATION......................... 1 IMPORTANT SAFETY INSTRUCTIONS....................2 CHAPTER 1 INTRODUCTION......................5 1.1 Packing List..........................5 1.2 Appearance and Components....................6 1.3 Dimension..........................8 CHAPTER 2 SPECIFICATIONS......................9 CHAPTER 3 INSTALLATION & USAGE.....................11 3.1 Media Loading........................11 3.2 Power Connection........................16 3.3 Peripherals Connection....................... - Page 3 HT100/HT130 User Manual Statement This manual content may be altered without permission, and our company reserves the rights to make changes without notice in technology, spare parts, hardware and software of the products. If more information is needed about the products, please contact our company.
-
Page 4: Manual Information
Manual Information This user manual contains basic information for product usage as well as for emergency measures that may be required. The installation and usage of printer driver, utility tool and HPRT BarTender® Ultralite are also included in the manual. Rev.1.2... -
Page 5: Important Safety Instructions
HT100/HT130 User Manual Important Safety Instructions Before using the appliance, please carefully read the following safety regulations in order to prevent any hazard or material damage. 1.Safety warning Warnings: The print head will become very hot during printing; avoid contact with the print head after printing has finished. - Page 6 HT100/HT130 User Manual Note: Violating following instructions may cause slight damage of the appliance. 1) If you observe a strange smoke, odour or noise from the printer, unplug it before taking following measures. • Switch off the printer and unplug the set from the mains.
- Page 7 HT100/HT130 User Manual 4.WEEE (Waste Electrical and Electric Equipment) This mark shown on the product or its literature indicates that the corresponding item should not be discarded at the end of its working life with other household waste. To prevent possible harm to the environment or human health from...
-
Page 8: Chapter 1 Introduction
HT100/HT130 User Manual Chapter 1 Introduction 1.1 Packing List Note: 1. Unpack the printer and keep the packing material in case you need to ship the printer in the future. 2. Any damages exist, please contact the local dealer. Printer... -
Page 9: Appearance And Components
HT100/HT130 User Manual 1.2 Appearance and Components ￭ Front View ￭ Rear View Rev.1.2... - Page 10 HT100/HT130 User Manual ￭ Inside View Note：The views above are for your reference. Ports vary by your choice. Rev.1.2...
-
Page 11: Dimension
HT100/HT130 User Manual 1.3 Dimension Rev.1.2... -
Page 12: Chapter 2 Specifications
HT100/HT130 User Manual Chapter 2 Specifications (2/1) Items Parameter HT100 HT130 Printing Method Thermal Transfer/Direct Thermal Printing Resolution 203dpi(8dots/mm) 300dpi(11.8dots/mm) Printing Speed Printing 127mm/s Max. 102mm/s Max. Printing Width 108mm Max. 106mm Max. Printing Length 15mm - 1200mm NUC976 Processor... - Page 13 HT100/HT130 User Manual (2/2) Items Parameter AC/DC switching power adapter Power I/P: AC100-240V, 50/60Hz, O/P: DC 24V/2.5A Operation 41℉(5℃)-104℉(40℃)，30%-85%(non-condensing) Environment Storage -4℉(-20℃)-122℉(50℃)，10%-90%(non-condensing) Dimension(L*W*H) 240*198*171mm Physical Characteristics Weight 2.26kg(excluding consumables) External label roll holder for 8’’ (203mm) OD label rolls Options & Accessories...
-
Page 14: Chapter 3 Installation & Usage
HT100/HT130 User Manual Chapter 3 Installation & Usage 3.1 Media Loading 3.1.1 Paper Roll Loading 1.Pull and lift the cover. 2.Pull the roll holders open and place the roll between them. Rev.1.2... - Page 15 HT100/HT130 User Manual 3.Press down the locking tab. 4.Pass the labels through label guides and adjust label guides to label’s width. Note: If your printer is under Thermal Line Printing Method, press down the printer cover until it snaps closed. Otherwise, continue the procedure in chapter 3.1.2.
- Page 16 HT100/HT130 User Manual 3.1.2 Ribbon Loading 1.After putting rewind spindle through printhead module, insert the right side of supply spindle into the rear pin, and then insert the left side into the rear wheel. Then do the same procedure for the ribbon rewind spindle.
- Page 17 HT100/HT130 User Manual 3.Press the lock and close the cover slightly. 4.Press down the cover until it snaps closed. Rev.1.2...
- Page 18 HT100/HT130 User Manual 3.1.3 External Paper Roll Loading If the paper roll is extremely large, users can load the paper roll outside(See the graph at right). Pass the paper through the external feed slot and then through paper guides. Adjust...
-
Page 19: Power Connection
HT100/HT130 User Manual 3.2 Power Connection 1.Make sure the printer’s power switch is in the off position. 2.Connect the AC adapter to power receptacle. 3.Connect the power cord to AC adapter. 4.Connect the other end of power cord to the outlet. -
Page 20: Peripherals Connection
Instructions as follows: 1. Power on printer. 2. Primary device search for outer Bluetooth devices. 3. If there are some outer Bluetooth devices, choose HT100/130. 4. Finish pairing. Detailed pairing methods, please refer to primary devices Bluetooth Names. After pairing, primary devices with virtual Bluetooth interface (smart phone , pocket PC, palm, notebook) can drive mobile thermal printer to print through such virtual Bluetooth interface. -
Page 21: Detection
HT100/HT130 User Manual 3.4 Detection When printing paper, the moveable label sensor is used to detect paper. The label sensor moves differently when using various kinds of paper. If user moves the sensor improperly, paper may not be detected, therefore the printer could not print paper. The following instructions tell users how to use label sensor correctly. - Page 22 HT100/HT130 User Manual Figure 2 (Left) Rev.1.2...
- Page 23 HT100/HT130 User Manual 3.4.2 Labels When printing labels (Figure 3) or double-row labels (Figure 4), the sensor shall be aimed at the left photoelectric hole (Figure 5), which is the original position. Figure 3 (Labels) Figure 4 (Double-row Labels) Rev.1.2...
- Page 24 HT100/HT130 User Manual Figure 5 (Left) Rev.1.2...
- Page 25 HT100/HT130 User Manual 3.4.3 Punched Hole Label When printing punched hole labels, move the sensor until it’s aimed at the right photoelectric hole (Figure 6). Figure 6 (Right) Rev.1.2...
- Page 26 HT100/HT130 User Manual 3.4.4 Blackmark Paper When printing blackmark paper (Figure 7), the sensor shall be aimed at the position of black mark (Figure 8). Figure 7 (Blackmark Paper) Figure 8 (aimed at blackmark’s position) Rev.1.2...
-
Page 27: Operation Panel
HT100/HT130 User Manual 3.5 Operation Panel 1.FEED button Turn on the printer. Press the feed button, and printer will automatically feed a label under “Label Mode”. Press the feed button, and the printer will feed the fixed distance under “Continuous Mode”. -
Page 28: Basic Function
HT100/HT130 User Manual 3.6 Basic Function 3.6.1 Power On/ Power Off Press “O” to power off the printer. Press “l”to power on the printer. 3.6.2 FEED Button 1.Turn on the printer. Press the feed button, and printer will automatically feed a label under “Label Mode”. - Page 29 4) Please refer to “Chapter 7 Seagull Windows Driver Instructions” for more detailed information. 3.Printing by HPRT BarTender Ultralite Program 1) Install the HPRT BarTender Ultralite program. 2) Edit a new label and print it. 3) Please refer to “Chapter 8 BarTender Ultralite Instructions” for more detailed information.
-
Page 30: Chapter 4 Interface
HT100/HT130 User Manual Chapter 4 Interface 4.1 USB Interface SIGNAL NAME VBUS 4.2 Other Optional Interfaces Serial Port SIGNAL NAME +5VDC Rev.1.2... - Page 31 HT100/HT130 User Manual Ethernet Port SIGNAL NAME Rev.1.2...
-
Page 32: Chapter 5 Maintenance & Adjustment
HT100/HT130 User Manual Chapter 5 Maintenance & Adjustment Adhesives and coatings of the media can transfer to the printer parts over time along the media path including the thermal print head and media sensor. This build-up can accumulate dust and debris. -
Page 33: Chapter 6 Printer Utility Tool Instructions
6.1 Installation Preparation Download application program in CD. eg: HPRTUtilityForLabel_Channel V2.0.0.3. 6.2 Usage Note: The screen may vary slightly by different operating systems and models. Take printer HT100 as example. Please refer to printer HT100 when using printer HT130. (1)Download “HPRTUtilityForLabel_Channel V2.0.0.3”... - Page 34 HT100/HT130 User Manual (2)Add/Modify/Delete Printer, Connect Test. ●Click “Add Printer”. Choose the printer and port(eg: USB), then click “OK”, showed in “Printer List”. Rev.1.2...
- Page 35 HT100/HT130 User Manual ●Click “Modify Printer”. Choose the printer and port(eg: COM1), then click “OK”, showed in “Printer List”. Rev.1.2...
- Page 36 HT100/HT130 User Manual ●Click “Delete Printer”. Click “OK” to delete the printer, and click “Cancel” to cancel the command. ●Click “Connect Test” to test whether the connection is successful or not. If connection succeeds, it shows as follows. If connection fails, it shows as follows.
- Page 37 HT100/HT130 User Manual (3)Function. ●Click “Printer Information”, showing printer information.(varies by different printers) ●Click “Print Test Text”. Type the text and set up the printing range. Click “Print”, then printer starts to print the test text. ●Click “Print Self Information”, then printer starts to print self-test page.
- Page 38 HT100/HT130 User Manual ●Click “Parameter Setting”. User can set up the BT config, print type, paper mode and so on. Click “Set”, and back to the main menu. ●Click “Model Print Test”, then printer starts to print models. ●Click “Restore Factory Settings”. Click “OK” to restore factory settings, and click “Cancel” to cancel the command.
-
Page 39: Chapter 7 Seagull Windows Driver Instructions
HT100/HT130 User Manual Chapter 7 Seagull Windows Driver Instructions 7.1 Introduction The following operating systems are supported: Microsoft Windows 10 (32 bit/64 bit) Microsoft Windows 8 (32 bit/64 bit) Microsoft Windows 7 SPI (32 bit/64 bit) Microsoft Windows Vista SP2 (32 bit/64 bit) -
Page 40: Installation
Under different operating systems, the screen may be slightly different. Take Windows 7 as example. Take printer HT100 as example. Please refer to printer HT100 when using printer HT130. To avoid the prevention, recommend to close the security software before installation. - Page 41 HT100/HT130 User Manual 5.Choose the installation directory, then click “Next”. 6.Click "Finish". Rev.1.2...
- Page 42 HT100/HT130 User Manual 7.Choose "Install printer drivers" , then click "Next". Note: If you have connected the printer to computer, it will detect and install the driver automatically.(eg.: USB port) 8.Choose "Install a driver for a Plug and Play printer, then click "Next".
- Page 43 HT100/HT130 User Manual 9.Enter a name for this printer, then click "Next". 10.Click"Finish". Rev.1.2...
- Page 44 HT100/HT130 User Manual 11.Click "Close", and the printer driver is installed successfully. 12.After installation, the icon will be found in ”Start”→“Devices and Printers”. Note: 1.If you have already installed the driver (No matter what kind of ports), it will generate a USB port automatically when connecting the printer to computer.
-
Page 45: Usage
HT100/HT130 User Manual 7.4 Usage 7.4.1 Printing Preferences 1.Click “Start”→“Devices and Printers”. Right click the icon and choose “Printing preferences”. Rev.1.2... - Page 46 HT100/HT130 User Manual 2.According to different needs, set up the page. ●Click “Stock”→”Name”, and choose the paper type. Rev.1.2...
- Page 47 HT100/HT130 User Manual ●Click “New Stock”, and set up a new stock. ●Click “Edit Stock”, and edit the stock. Rev.1.2...
- Page 48 HT100/HT130 User Manual ●Click “Delete Stock”, and delete the stock. ●Choose “Orientation” or “Effects”, showed in the “Preview”. Rev.1.2...
- Page 49 HT100/HT130 User Manual Rev.1.2...
- Page 50 HT100/HT130 User Manual ●Click “Preset”→“Name”, and back to the default settings. ●Click “Manage”, and change the settings. Rev.1.2...
- Page 51 HT100/HT130 User Manual 3.Click “Graphics”, and edit the pictures. 4.Click “Stock”. Rev.1.2...
- Page 52 HT100/HT130 User Manual ●Click “Method”, and choose the printing method. ●Click “Type”, and choose the printing type. Rev.1.2...
- Page 53 HT100/HT130 User Manual ●Click “Post-Print Action”, and choose the method of media handling. Rev.1.2...
-
Page 54: Printer Properties
HT100/HT130 User Manual 7.4.2 Printer Properties 1.Click “Start”→“Devices and Printers”. Right click the icon and choose “Printer properties”. Rev.1.2... - Page 55 HT100/HT130 User Manual 2.Click “General”→“Print Test Page”, and printer will print labels with current settings. Rev.1.2...
- Page 56 HT100/HT130 User Manual 3.Click “Ports”, then choose the port needed. Rev.1.2...
-
Page 57: Removing
HT100/HT130 User Manual 7.4.3 Label’s Width USER(4.00 in×4.00 in) 2×4(2.00 in×4.00 in) 4×4(4.00 in×4.00 in) 4×6(4.00 in×6.00 in) 7.5 Removing Note: Please turn off the printer or unplug the USB cable before removing the driver. 1.Double click Seagull Windows Driver 2.Read and agree the license agreement. - Page 58 HT100/HT130 User Manual 3.Choose the installation directory, then click “Next”. 4.Click"Finish". Rev.1.2...
- Page 59 HT100/HT130 User Manual 5.Select “Remove printer drivers”, then click “Next”. 6.Select “Remove printers”, then click “Next”. Rev.1.2...
- Page 60 HT100/HT130 User Manual 7.Select printer’s name, then click “Next”. 8.Please unplug the USB cable or turn off the ptinter when appearing the following prompt. Rev.1.2...
- Page 61 HT100/HT130 User Manual 9.Click “Finish”. 10.Restart the computer when appearing the following prompt, or continue step 11. Rev.1.2...
- Page 62 HT100/HT130 User Manual 11.Click “Close”. The driver has been removed successfully. Rev.1.2...
-
Page 63: Chapter 8 Bartender Ultralite Instructions
HT100/HT130 User Manual Chapter 8 BarTender Ultralite Instructions 8.1 Introduction This chapter provides instructions on BarTender Ultralite program according to PC operating systems(OS). The followings are supported. Microsoft Windows 10 (32 bit/64 bit) Microsoft Windows 8 (32 bit/64 bit) Microsoft Windows 7 SPI (32 bit/64 bit) - Page 64 Under different operating systems, the screen may be slightly different. Take Windows 7 as example. Take printer HT100 as example. Please refer to printer HT100 when using printer HT130. To avoid the prevention, recommend to close the security software before installation.
- Page 65 HT100/HT130 User Manual 4.Click “Next”. 5.Read and accept the license agreement, then click "Next". Rev.1.2...
- Page 66 HT100/HT130 User Manual 6.Select "Features" and installation location, then click "Next". 7.Click "Install". Rev.1.2...
- Page 67 HT100/HT130 User Manual 8.Click "Finish". 9.Back to desktop, and you will see the icon of BarTender Ultralite. Double click it and get down to use. Rev.1.2...
- Page 68 HT100/HT130 User Manual 8.4 Usage 8.4.1 Page Settings 1.Double click the icon, then choose the edition. Click “OK”. (The edition may be changed according to different needs.) 2.Click “Start a new BarTender document”. Rev.1.2...
- Page 69 HT100/HT130 User Manual 3.Choose “Blank Template”, then click “Next”. 4.If the predefined stocks don’t meet your need, tick “Specify Custom Settings”. Then click”Next”. Rev.1.2...
- Page 70 HT100/HT130 User Manual 5.Tick “Single item per page”, then click “Next”. (If you print multiple labels, tick “Multiple columns and/or rows of items per page ”.) 6.Edit the side edges, then click “Next”. Rev.1.2...
- Page 71 HT100/HT130 User Manual 7.Choose the item shape, then click “Next”. 8.Edit the template size, then click “Next”. Rev.1.2...
- Page 72 HT100/HT130 User Manual 9.Based on your need, edit the template background. Then click ”Next”. 10.Finish the settings, showed in the “Review” and “Preview”. Then click “Finish”. Rev.1.2...
- Page 73 HT100/HT130 User Manual 8.4.2 label Edit 1.Click the icon of code 2.Choose the code, then click “Select”. Rev.1.2...
- Page 74 HT100/HT130 User Manual 3.Click the blank, showing the code. Rev.1.2...
- Page 75 HT100/HT130 User Manual 4.Double click the code and edit it. User can set up the size, font, border and so on. Finishing the changes, click “Close”. Rev.1.2...
- Page 76 HT100/HT130 User Manual 5.Click the icon of character , then enter the text. Rev.1.2...
- Page 77 HT100/HT130 User Manual 6.Click the icon of picture , then edit the pictures. Rev.1.2...
- Page 78 HT100/HT130 User Manual 7.Compose the text. 8.Finish all the settings. Click “Print” and a new label will be printed. Rev.1.2...
Need help?
Do you have a question about the HT100 and is the answer not in the manual?
Questions and answers