Mountfield MM2605 Instruction Booklet
  1. Manuals
  2. Brands
  3. Mountfield Manuals
  4. Brush Cutter
  5. MM2605
  6. Instruction booklet

Mountfield MM2605 Instruction Booklet

Hide thumbs
Table of Contents

Advertisement

Quick Links

1
J
J.2
A
2
J.1
E
G
I
F
K
D
B
H
C (C.1)
C (C.2)
L

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MM2605 and is the answer not in the manual?

Questions and answers

Summary of Contents for Mountfield MM2605

  • Page 1 C (C.1) C (C.2)

  • Page 7: Table Of Contents

    WARNING!: READ THOROUGHLY THE INSTRUCTION BOOKLET BEFORE USING THE MACHINE. Keep for future reference INDEX 1. GENERAL INFORMATION 1. GENERAL INFORMATION ........1 2. SAFETY REGULATIONS ........2 HOW TO READ THE MANUAL 3. GETTING TO KNOW THE MACHINE ..... 4 Description of the machine and planned use..

  • Page 8: Safety Regulations

    – Keep the petrol and fuel mixture in 2. SAFETY REGULATIONS approved fuel containers, in a safe place, away from any naked lights or heat sources. – Keep the containers out of 2.1 TRAINING the reach of children. – Keep the containers free of grass, Become acquainted with the controls leaves, or excessive grease;...
  • Page 9 • Check that there is nobody within 15 • Do not touch the engine parts, which metres of the machine’s range of action heat up during use. Burns hazard. or within 30 metres for heavier cutting; • To avoid the risk of fire, do not leave the •...

  • Page 10: Getting To Know The Machine

    3. GETTING TO KNOW THE MACHINE 2.4 MAINTENANCE, STORAGE AND TRANSPORT Ensure regular maintenance and 3.1 DESCRIPTION OF THE MACHINE correct storage to maintain machine AND PLANNED USE safety and high performance level. This machine is a garden tool, namely a Never use the machine with worn or portable brush cutter/grass edge trimmer damaged parts.

  • Page 11: Safety Signs

    WARNING! Petrol is flammable. 3.1.3 User types Allow engine to cool at least 2 minutes before refuelling. This machine is intended for use by consumers, i.e. non-professional operators. The machine is intended for "DIY" use only. Beware of blade thrust. 3.2 SAFETY SIGNS WARNING! - Keep away The machine has various symbols on it...

  • Page 12: Assembly

    Connection point (of the harness) 4.2.2 Assembly of “DUPLEX” handle Harness 1. Single belt 1. Loosen the central knob (fig. 4.A) 2. Double belt and remove the capfig. 4.B). K. Angle transmission 2. Insert the handle bar (fig. 4.C), making L.
  • Page 13 2. Position the guard (fig. 5. C) on the holes of pressing until a click is heard; then fasten the plate (fig. 5. B) of the drive tube (fig. 5. D). in place using the screw (fig. 7.G). 3. Fix the guard (fig. 5. C) by fully tightening the screws (fig.

  • Page 14: Mounting The Rod (Models With Separate Rod)

    enters the hole of the angle transmission 5.4 THROTTLE SHUTTER (fig. 8.B, fig. 9.B), blocking rotation. BUTTON (OPTIONAL) 2. Loosen the nut (fig. 8.G, fig. 9.G) clockwise and remove the cup (fig. 8.F, fig. 9.F). Used to turn on the engine 3.

  • Page 15: Safety Checks

    6.1.1 Using harnesses Cutting means (figs. Not damaged or worn. 1.C.1; 1.C.2) The harness must be put on before Metal blade (if Sharp connecting the machine to the special fitted) (fig. 1.C.2) coupling and the belts must be adjusted Air filter (fig. 21.A) Clean to suit the operator’s height and build.

  • Page 16: Operation

    IMPORTANT To avoid breaking the starter the harnesses correctly, grip the machine firmly cable, do not pull the whole length of it or and make the movements required by the job. let it slide along the edge of the cable guide To operate with the machine, hole.

  • Page 17: Advice On Operation

    In any case, cutting around pavements, NOTE Avoid using the machine at full foundations, walls, etc. can cause power for the first 6- 8 working hours. greater wear than normal to the line. IMPORTANT Stop the engine ( par. d. Cutting around trees 6.5) when moving between work areas.

  • Page 18: Preparing The Fuel Mixture

    • Wear protective gloves; 7.2.3 Preparation and storage • Apply the blade protection device, except of the fuel mixture when working directly on the blade. To prepare the fuel mixture: • The frequency and types of maintenance are summarised in the "Maintenance –...

  • Page 19: Cleaning The Air Filter

    • To avoid overheating and damage to the 8. EXTRAORDINARY MAINTENANCE engine, always keep the cooling air vents clean and free of sawdust and debris. 8.1 CUTTING MEANS MAINTENANCE 7.5 CLEANING THE AIR FILTER When servicing the cutting means, bear in mind that, even though the spark plug cable is IMPORTANT Cleaning the air filter is disconnected, the cutting means can still move.

  • Page 20: Tuning Minimum Speed

    • Remove the line cutting knife (Fig. 25.A) in When you wish to start using the a vice and sharpen it using a flat file, being machine again, prepare it as indicated careful to retain the original cutting angle. in chapter “6. Using the machine" . •...

  • Page 21: Warranty Coverage

    • Use of accessories not supplied or 12. WARRANTY COVERAGE approved by the manufacturer. The warranty does not cover: The warranty covers all material and • Normal wear and tear of consumables, manufacturing defects. The user must such as cutting means, safety bolts. follow all the instructions provided in •...
  • Page 22 PROBLEM PROBABLE CAUSE REMEDY 5. If the engine floods The starter grip has been driven Remove the spark plug (fig. 22) and repeatedly with the starter inserted. pull gently on the starter grip (fig. 12.I, fig. 13.I) to eliminate excess fuel, then dry the electrodes of the spark plug and refit it on the engine.

Table of Contents

Save PDF