Subscribe to Our Youtube Channel
Related Manuals for CAME ZLJ14
Summary of Contents for CAME ZLJ14
- Page 1 CONTROL PANEL FOR 24 V GEARMOTORS FA 00044 -E N INSTALLATION MANUAL ZLJ14 English...
- Page 2 All connections are quick-fuse protected. Intended use Control panel Gearmotor ZLJ14 AMICO - AXO - F4000 - FAST - FERNI - FROG - FROG J - MYTO Any installation and/or use other than that specified in this manual is forbidden. Technical data...
- Page 3 Description of parts 1. Transformer 2. Power supply on warning LED 3. Display 4. Memory roll board connector 5. Programming buttons 6. Programming warning LED 7. Display brightness adjusting trimmer 8. Connector for the R700 card 9. AF card connector 10.
- Page 4 Cable types and minimum thicknesses Cable length Cable length Connection Cable type 1 < 15 m 15 < 30 m 230 V AC power-supply to control panel H05RN-F 3G x 1.5 mm 3G x 2.5 mm Encoder gearmotor power supply* 3 x 1.5 mm 3 x 2.5 mm Power supply to gearmotor**...
- Page 5 ELECTRICAL CONNECTIONS Power supply to accessories Possible output of the second radio-receiver Terminals for powering the 24 V AC/DC Electric-lock connection channel (NO contact). accessories Maximum power: 50 W rated at 12 V - 15 W max Contact rated for: 500 mA - 24 V DC.
- Page 6 Command and control devices Command and control devices Before fitting any snap-in cards (such as the AF or R700), YOU MUST CUT OFF THE POWER MAINS, and disconnect the power mains. Fit the R700 decoding card for recognition of the TSP00 sensor or the LT001 card reader.
- Page 7 Signaling devices Signaling devices Gate open warning light (Contact rated for: Courtesy light (contact rated for: 24 V - 25 W max). 24 V - 3 W max). Auxiliary connection of an outdoor light which can be positioned To warn that the gate is open. where you like, to increase lighting in the driveway/parking area.
- Page 8 Connecting the safety devices (i.e. the safety test) At each opening or closing command, the card checks the efficiency of the safety devices, such as photocells). Any anomalies will inhibit all commands. Select from the [Safety Test] which of inputs CX, CY or CZ to turn on. FUSIBILE 200m A DIR / 10 2 T X C...
- Page 9 PROGRAMMING PROGRAMMING Description of programming commands the <-----> signs on the display are for: - showing the currently selected item The ESC button is for: The ENTER key is for: - exiting menus; - entering menus; - cancelling changes. - confirming or memorizing set values. The <...
- Page 10 Meaning of the menu items abbreviations [Travel sens] Gate Run Sensibility [Partial open] Partial Opening [Maint Action] Maintained Action [Auto Close] Automatic Closing [Config] Configuration [Assoc Function] Associated Function [Set Travel] Set gate-leaf Travel [Open Accel] Opening Soft-Stop as a percentage [CloseAccel] Closing Soft-Stop as a percentage [Opn Slw Dwn]...
- Page 11 [ENCODER] Default [Sensibility] [Enabled] / [Disabled] [Enabled] [Travel sens] ◦+] ◦+] [Slw Dwnsens] [Enc Slow Down] [ON] / [OFF] [ON] [1%] ⇨ [40%] [Opn Slw Dwn] [10%] [1%] ⇨ [40%] [Cls SlwDwn] [10%] [CClose Accel] [1%] ⇨ [15%] [15%] [OpenAccel] [1%] ⇨...
- Page 12 [Obstruc Detct] [Disabled] / [Enabled] With the leaf closed, open or after a total stop, the operator remains idle if the safety devices, like photocells or sensitive safety-edges) detect and obstruction. [Safety Test] [Disabled] / [CX] / [CY] / [CZ] / [CX+CY] / [CX+CZ] / [CY+CZ] / [CX+CY+CZ] After every opening or closing command, the board will check whether the photocells are working properly [Prefl...
- Page 13 Gate run setting menu [Set Travel] [Motor type] [FROG-F4024E] / [FROG-J] / [FROG-FL] / [AMICO] / [MYTO] / [AXO] / [FAST] / [FERNI] / [ATI] Setting the type of operator installed in the system. [50%] ⇨ [100%] [Travel rate %] Adjusting the maneuvering speed, calculated as a percentage.
- Page 14 [1%] ⇨ [15%] [Open Accel] Adjusting the soft-spot starting point as a percentage (from 1% to 15% of the complete travel) before the opening endstop point. [Travel calibr] Automatic calibration of the gate-leaf run (see the TRAVEL CALIBRATION paragraph) Time settings menu SET TIMES [0 s] ⇨...
- Page 15 [Save memory] To save system users and settings in memory roll. Confirm saving with ENTER. [Load memory] For uploading the data saved in the memory roll onto the electronic board. If the boards feature different versions, you may only upload the users. Info menu [INFO] [Version]...
- Page 16 Entering a new user 1. From the 2. Select [Confirm? [USERS], select < Add User > Add User (Yes)] and press [Add User]. Press <Confirm?(yes)> ENTER to confirm. ENTER to confirm. 3. Select the function 4..a code to enter will Assoc Function to associate to users.
- Page 17 Modify code 1. From the 2. Select the user name [USERS], select < Change Code > Change Code of which you want to [Change Code]. edit the code and press Change Code Press ENTER to ENTER to confirm. confirm < 002: --U002-- > 3.
- Page 18 Travel calibration Before calibrating the gate run, check that the maneuvering area is free from any obstruction and that there are both opening and closing mechanical stops. The mechanical end-stops are obligatory. Important! During the calibration, all safety devices will be disabled except for the PARTIAL STOP one. 1.
- Page 19 DIAGRAM OF THE SLOW-DOWN AND FINAL APPROACH POINTS AND FOR THE ENCODER DEVICE The run area and slow down and approach points are tested according to the parameters set forth by Technical Standards EN 12455 and EN 12453 for compliance with the impact forces generated by the running leaves. = Normal speed B* = Slowed-down speed = Encoder intervention zone with movement inversion...
- Page 20 Came S.p.A. Came S.p.A. Via Martiri Della Libertà, 15 Via Cornia, 1/b - 1/c 31030 Dosson di Casier Dosson di Casier 33079 Sesto al Reghena Sesto al Reghena Treviso Treviso - Italy Pordenone Pordenone - Italy (+39) 0422 4940 (+39) 0434 698111...
Need help?
Do you have a question about the ZLJ14 and is the answer not in the manual?
Questions and answers