Related Manuals for MachineryHouse HFLP-35
Summary of Contents for MachineryHouse HFLP-35
- Page 1 Page 1 Instructions Manual for HFLP-35 (D9506) 11/11/2016 INSTRUCTION MANUAL HFLP-35 Portable Magnetic Drill - Low Profile (240V) Ø35mm Drill Capacity D9506...
- Page 2 Page 2 Instructions Manual for HFLP-35 (D9506) 11/11/2016 Low Profile Magnetic Core Drill System Warning: Only tools equipped with over load protection, when motor has been cut off due to over load, always switch on machine with no load for at least 3 minutes to reduce...
- Page 3 Page 3 Instructions Manual for HFLP-35 (D9506) 11/11/2016 General Machinery Safety Instructions Machinery House requires you to read this entire Manual before using this machine. 1. Read the entire Manual before starting 14. Use correct amperage extension cords. machinery. Machinery may cause serious injury if Undersized extension cords overheat and lose not correctly used.
- Page 4 Page 4 Instructions Manual for HFLP-35 (D9506) 11/11/2016 Magnetic Drilling Machine Safety Instructions Machinery House requires you to read this entire Manual before using this machine. 1. Maintenance. Make sure the Magnetic Drill is chips. Never clear chips when the drill is running.
- Page 5 Page 5 Instructions Manual for HFLP-35 (D9506) 11/11/2016...
- Page 6 Page 6 Instructions Manual for HFLP-35 (D9506) 11/11/2016 Good balance for Crank Lever Carrying Quick-release tool holder Annular cutter (Not included) Pilot pin (Not included) Motor switch Magnet switch LED Work Light Standard Accessories Power Input 1100W * Safety Chain...
- Page 7 Page 7 Instructions Manual for HFLP-35 (D9506) 11/11/2016 GENERAL SAFETY INSTRUCTIONS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool.
- Page 8 Page 8 Instructions Manual for HFLP-35 (D9506) 11/11/2016 conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
- Page 9 Page 9 Instructions Manual for HFLP-35 (D9506) 11/11/2016 IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
- Page 10 Page 10 Instructions Manual for HFLP-35 (D9506) 11/11/2016 SPECIFIC SAFETY RULES AND REGULATIONS WARNING: For your own safety, never use coolant containing water while operating at more than a 90 degree from horizontal. Spray-type coolant which do not contain any ingredient of water should be used ! Always use safety chain.
- Page 11 Page 11 Instructions Manual for HFLP-35 (D9506) 11/11/2016 MOUNTING ANNULAR CUTTERS CAUTION: Never use a cutting tool that is larger than the maximum rated capacity of the machine. To insert an annular cutter, first insert the pilot pin into the cutter.
- Page 12 Page 12 Instructions Manual for HFLP-35 (D9506) 11/11/2016 annular cutter will produce long unbroken chips, which produce a “bird’s” nest. shaped bundle of chips around the cut. NOTE: Always ensure that the cutting tool is sharp. A dull cutter typically will have finer and/or choppy shavings.
- Page 13 Page 13 Instructions Manual for HFLP-35 (D9506) 11/11/2016 THE ARBOR SHAFT Keep the arbor shaft free of dirt and lightly grease as needed. If the mechanism noisy, it may be dirty or have a chip lodged in it. Clean and re-grease as needed.
- Page 14 Page 14 Instructions Manual for HFLP-35 (D9506) 11/11/2016 Wiring...
- Page 15 Page 15 Instructions Manual for HFLP-35 (D9506) 11/11/2016 Exploded View...
- Page 16 Page 16 Instructions Manual for HFLP-35 (D9506) 11/11/2016 Parts list Parts Name Q'TY Parts Name Q'TY INTERNAL CIRCLIP R-19 SOCKET CAP SCREW M6 x 30 ARBOR WASHER ø10 x ø18.5 x 0.8 SPRING WASHER M6 COOLANT SEAL ø10.2 x ø12 x 15 LED LAMP SPRING ø1.2 x ø10 x ø12.4 x 7T x 54L...
Need help?
Do you have a question about the HFLP-35 and is the answer not in the manual?
Questions and answers