Use this manual along with the advanced diagnostic tests to troubleshoot problems effectively. Before servicing a Lenovo product, be sure to read all the information under Chapter 1 “Safety information” on page 1 and Chapter 2 “Important service information” on page 19.
This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-Lenovo features or options not covered by this inspection guide. If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem.
4. Check for cracked or bulging batteries. 5. Remove the cover. 6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo alterations. 7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.
– Use the round ground prong of the ac plug on ac-operated computers. Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician. Safety notices (multilingual translations) The safety notices in this section are provided in the following languages: •...
Customer Support Center if they need any assistance in obtaining or installing any software fixes, drivers, and Unified Extensible Firmware Interface basic input output system (UEFI BIOS) downloads. Telephone numbers for Lenovo Support are available at: http://www.lenovo.com/support/phone • System Disassembly/Reassembly videos that show the FRU removals or replacements for the Lenovo authorized service technicians are available in the following support site: http://www.lenovoservicetraining.com/ion/...
• Avoid bending a system board and hard pushing to prevent cracking at each ball-grid-array (BGA) chipset. FRU identification Use Lenovo eSupport to identify major FRUs, FRU part numbers, and FRU descriptions for a product at an MT - serial number level. Examples of major FRUs are hard disk drive, system board, liquid crystal display (LCD), and memory module.
• Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force • Damage caused by liquid spilled into the system • Damage caused by the improper insertion of a personal-computer card (PC card) or the installation of an incompatible card •...
This computer supports only batteries specially designed for this specific system and manufactured by Lenovo or an authorized builder. The system does not support unauthorized batteries or batteries designed for other systems. If an unauthorized battery or a battery designed for another systems is installed, the system will not charge.
The Lenovo E4030/E4070 computers come with pre-installed OneKey Recovery System. In order to save application files and the initial backed up files of the system, the hard disk in a Lenovo computer includes a hidden partition when it is shipped. If you need to restore the system to the point of your first boot up, just enter Lenovo OneKey Recovery System and run System Recovery.
• For Windows 10: Click Start, and then select Sleep from Power menu option. To return to normal operation, press any key. In certain circumstances, the computer goes into sleep mode automatically: • After a period of inactivity specified in power plan settings •...
Chapter 5. Passwords As many as three passwords may be needed for any Lenovo computer: the power-on password (POP), the hard disk password (HDP), and the administrator password. If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on.
CRUs, you can either install the CRU yourself or you can request that a Service Provider install the CRU according to the warranty service for your product. If you intend on installing the CRU, Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped with your product and are available from Lenovo at any time upon request.
Page 40
Table 1. Major FRUs (continued) FRU parts FRU descriptions Self-service Optional-service FRU No. Upper case Upper Case Q 80T8 FP W/KB NL 5CB0M31751 Upper case Upper Case Q 80T8 FP W/KB HG 5CB0M31746 Upper case Upper Case Q 80T8 FP W/KB ICE 5CB0M32039 Upper case Upper Case Q 80T8 FP W/KB IT...
Page 41
Table 1. Major FRUs (continued) FRU parts FRU descriptions Self-service Optional-service FRU No. Upper case Upper Case Q 80T8 NFP W/KB KO 5CB0M31721 Upper case Upper Case Q 80T8 NFP W/KB LA 5CB0M31764 Upper case Upper Case Q 80T8 NFP W/KB INDIA 5CB0M31983 Upper case Upper Case Q 80T8 NFP W/KB PO...
Table 1. Major FRUs (continued) FRU parts FRU descriptions Self-service Optional-service FRU No. System board MBQ80T8NOK I76567U 5B20M31716 UMANRAM2BAT System board MBQ80T8WIN I76567U 5B20M31720 UMANRAM2BAT Major FRUs and CRUs (for V510–15IKB) Chapter 7 Locations...
Page 48
Table 2. Major FRUs FRU parts FRU descriptions FRU No. Self-service CRU Optional-service LCD unit LCD unit Thermal ThermalModule Q 80T8 DIS W/Fan 5H40M31771 Module Thermal 5H40L46632 Thermal Module Q 80SY UMA W/Fan Module USB board USB Board Q 80TA W/Cable 5C50M31604 LED board LED Board Q 80SY W/Cable...
Page 49
Table 2. Major FRUs (continued) FRU parts FRU descriptions Self-service CRU Optional-service FRU No. Upper case Upper Case Q 80TA FP W/KB UK 5CB0M31625 Upper case Upper Case Q 80TA FP W/KB AR-E 5CB0M32070 Upper case Upper Case Q 80TA FP W/KB FR-AR 5CB0M31947 Upper case Upper Case Q 80TA FP W/KB BE...
Page 50
Table 2. Major FRUs (continued) FRU parts FRU descriptions Self-service CRU Optional-service FRU No. Upper case Upper Case Q 80TA NFP W/KB CZ-SK 5CB0M31855 Upper case Upper Case Q 80TA NFP 5CB0M31717 W/KBUSINT'E Upper case Upper Case Q 80TA NFP W/KB FR 5CB0M31902 Upper case Upper Case Q 80TA NFP W/KB GR...
Page 53
Table 2. Major FRUs (continued) FRU parts FRU descriptions Self-service CRU Optional-service FRU No. System board MBQ80TA WIN I37100U DIS OL 2BA 5B20M32076 5B20M31894 System board MBQ80TA NOKI37100U DIS NOL 5B20M31891 System board MBQ80TA WINI37100U DIS NOL NUL System board MBQ80TA NOKI37100U DIS NOL 2BA 5B20M31722 5B20M31844...
Page 54
Table 2. Major FRUs (continued) FRU parts FRU descriptions Self-service CRU Optional-service FRU No. System board MBQ80TA NOKI57200U 5B20M31866 UMA4GNOLNUL System board MBQ80TA WINI57200U 5B20M31736 UMA4GNOLNUL System board MBQ80TA NOKI57200U 5B20M31756 UMA4GNOL2BA System board MBQ80TA WINI57200U 5B20M31884 UMA4GNOL2BA System board MBQ80TA NOK I57200U DIS OL NUL 5B20M31796 5B20M31582...
Page 55
Table 2. Major FRUs (continued) FRU parts FRU descriptions Self-service CRU Optional-service FRU No. System board MBQ80TA NOKI77500U 5B20M31684 DIS4GNOL2BA System board MBQ80TA WINI77500U 5B20M31811 DIS4GNOL2BA System board MBQ80TA NOKI77500U UMA4G 5B20M31588 OLNUL System board MBQ80TA WINI77500U UMA4G 5B20M32081 OLNUL System board MBQ80TA NOKI77500U UMA4G 5B20M32079...
Page 56
Table 2. Major FRUs (continued) FRU parts FRU descriptions Self-service CRU Optional-service FRU No. System board MBQ80TA NOKI56200U DIS4G 5B20M31765 OLNUL System board MBQ80TA WINI56200U DIS4G 5B20M31966 OLNUL System board MBQ80TA NOKI56200U DIS4G 5B20M31955 OL2BA System board MBQ80TA WINI56200U DIS4G OL2BA 5B20M31911 5B20M31987 System board...
Page 57
Table 2. Major FRUs (continued) FRU parts FRU descriptions Self-service CRU Optional-service FRU No. System board MBQ80TA NOK I56200U UMA OL 5B20M31969 System board MBQ80TA WIN I56200U UMA OL 2BA 5B20M31647 5B20M31680 System board MBQ80TA NOKI56200U UMA NOL 5B20M32072 System board MBQ80TA WINI56200U UMA NOL 5B20M31827 System board...
Page 58
Table 2. Major FRUs (continued) FRU parts FRU descriptions Self-service CRU Optional-service FRU No. System board MBQ80TA NOK I56267U DIS OL 2BA 5B20M31691 5B20M31583 System board MBQ80TA WIN I56267U DIS OL 2BA System board MBQ80TA NOKI56267U DIS NOL 5B20M31637 System board MBQ80TA WINI56267U DIS NOL NUL 5B20M32018 5B20M31988...
Page 59
Table 2. Major FRUs (continued) FRU parts FRU descriptions Self-service CRU Optional-service FRU No. System board MBQ80TA WINI76500U UMA4G 5B20M32068 OL2BA System board MBQ80TA NOKI76500U 5B20M31874 UMA4GNOLNUL System board MBQ80TA WINI76500U 5B20M31664 UMA4GNOLNUL System board MBQ80TA NOKI76500U 5B20M31903 UMA4GNOL2BA System board MBQ80TA WINI76500U 5B20M31883 UMA4GNOL2BA...
Page 60
Table 2. Major FRUs (continued) FRU parts FRU descriptions Self-service CRU Optional-service FRU No. System board MBQ80TA WINI76567U 5B20M32028 DIS4GNOLNUL System board MBQ80TA NOKI76567U 5B20M32071 DIS4GNOL2BA System board MBQ80TA WINI76567U 5B20M31737 DIS4GNOL2BA System board MBQ80TA NOKI76567U UMA4G 5B20M32053 OLNUL System board MBQ80TA WINI76567U UMA4G 5B20M31997 OLNUL...
LCD FRUs (for V510–15IKB) Table 4. LCD FRUs No. FRU FRU descriptions Self-service Optional-service PN number parts LCD Bezel Q 80TA W/O Camera 5B30M31858 bezel LCD Bezel Q 80TA 5B30M31946 bezel Panel LG LP156WHU-TPH1 HDT AG S NB 5D10K81461 Panel 5D10K81086 INX N156BGA-EA2 HDT AG S NB Panel...
Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped with your product and are available from Lenovo at any time upon request. You can find a list of CRUs for your product in this Hardware Maintenance Manual. An electronic version of this manual can be found at http://www.lenovo.com/UserManuals.
Page 70
180 degrees more (Cross-section) Notes: • Ensure that you use the correct screw. If you have a torque screwdriver, tighten all screws firmly to the torque specified in the screw information table for each step. • Ensure that torque screwdrivers are calibrated correctly following country specifications. Hardware Maintenance Manual...
Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped with your product and are available from Lenovo at any time upon request. You can find a list of CRUs for your product in this Hardware Maintenance Manual. An electronic version of this manual can be found at http://www.lenovo.com/UserManuals.
Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge (ESD). Before touching it, establish personal grounding by touching a ground point with one hand or by using an electrostatic discharge strap. 1010 Optical disk drive/Removable battery Removal steps of the Optical drive/Removable battery with spring-loaded latch Push forward the spring-loaded latch and hold it in the unlocked position Gently pull the optical disk drive/removable battery out...
Page 73
Removal steps of the Optical drive/Removable battery without spring-loaded latch Remove the screw Gently pull the optical disk drive/removable battery out Step Screw (quantity) Color Torque SCREW M2*5.5mm, flat-head, nylok-coated Black 1.85 +/- 0.15kgf-cm Loosen the screw , and then remove the bracket in the direction shown by arrow Torque Step Screw (quantity)
Note: If the Certificate of Authenticity (COA) label (b) is attached to a replaced part, return the replaced part to the customer, or provide a letter to the customer stating the original label part number, serial number, and product key. The following illustration shows the location of each label on Lenovo V510–14IKB. Hardware Maintenance Manual...
Page 75
Indonesia rating label SLP label GML label SA label ARG LBL label Wlan Indonesia label Israel label The following illustration shows the location of each label on Lenovo V510–15IKB. Rating label Korean label KCC label Rating print label Brazil label COA label...
The Lenovo Solution Center program provides an automatic battery diagnostic test that determines if the battery pack is defective. A battery pack FRU should not be replaced unless this diagnostic test shows that the battery is defective.
1050 Hard disk drive or solid-state hybrid drive For access, remove these FRUs in order: • “1010 Optical disk drive/Removable battery” on page 66 • “1020 Base cover assembly” on page 68 • “1040 Battery pack” on page 70 Attention: •...
Detach the bracket by removing the four screws Step Screw (quantity) Color Torque M3 × 3mm, flat-head, nylon-coated (4) Black 3.0 +/- 0.3kgf-cm When installing: Ensure that the hard disk drive or solid-state hybrid drive is firmly attached. 1060 Secondary battery board For access, remove these FRUs in order: •...
Removal steps of the optical disk drive connector Open the socket , and then pull out the optical disk drive cable Remove two screws , and then remove the optical disk drive connector in the direction shown by arrow Step Screw (quantity) Color Torque...
Remove one screw , and then remove the USB board in the direction shown by arrow Step Screw (quantity) Color Torque M2 × 3mm, flat-head, nylon-coated (1) Black 1.85 +/- 0.15kgf-cm When installing: Ensure that the USB board is firmly attached. 1090 Finger printer board and finger printer bracket For access, remove these FRUs in order: •...
Remove one screw , and then remove the finger printer bracket and finger printer board in the direction shown by arrow Step Screw (quantity) Color Torque Black M2 × 3mm, flat-head, nylon-coated (1) 1.85 +/- 0.15kgf-cm When installing: Ensure that the finger printer bracket and finger printer board are firmly attached. 1100 DC-in cable For access, remove these FRUs in order: •...
Flip the hinge bracket in the direction shown by arrow Detach the DC-in cable , and then gently remove the DC-in cable from the cable guide When installing: Ensure that the DC-in cable is firmly attached. 1110 Wireless-LAN /Bluetooth card For access, remove these FRUs in order: •...
Removal steps of the Wireless-LAN /Bluetooth card Unplug the two wireless Lan cable (black and white) in the direction shown by arrow , and then remove the screw Step Screw (quantity) Color Torque Black M2 × 4.7 mm, flat-head, nylon-coated (1) 1.85 +/- 0.15kgf-cm Remove the card in the direction shown by arrow When installing:...
Page 84
Removal steps of the thermal fan assembly and heat sink assembly Open the socket , pull out the LCD cable , and then release it from the cable guide. Detach the fan cable connector Remove three screws , and then remove the fan assembly in the direction shown by arrow Remove six screws , and then remove the heat sink assembly in the direction shown by arrow Hardware Maintenance Manual...
When installing: Ensure that the thermal fan assembly and heat sink assembly are firmly attached. 1130 Speaker assembly For access, remove these FRUs in order: • “1010 Optical disk drive/Removable battery” on page 66 • “1020 Base cover assembly” on page 68 •...
Remove three screws , and then remove the OneLink board Torque Step Screw (quantity) Color M2 × 3mm, flat-head, nylon-coated (3) Black 1.85 +/- 0.15kgf-cm When installing: Ensure that the OneLink board is firmly attached. Removal steps of the power board (for the models without OneLink+ dock port) Open the socket , and then pull out the power cable Remove two screws...
1150 LED board For access, remove these FRUs in order: • “1010 Optical disk drive/Removable battery” on page 66 • “1020 Base cover assembly” on page 68 • “1040 Battery pack” on page 70 Removal steps of the LED board Open the socket , and then pull out the LED board cable Remove one screw...
• “1110 Wireless-LAN /Bluetooth card” on page 76 • “1120 Thermal fan assembly and Heat Sink assembly” on page 77 • “1130 Speaker assembly” on page 79 • “1140 Power board/ OneLink board” on page 79 • “1150 LED board” on page 81 Removal steps of the system board Open the socket , and then pull out the touch pad cable connector...
• “1040 Battery pack” on page 70 • “1100 DC-in cable” on page 75 • “1110 Wireless-LAN /Bluetooth card” on page 76 • “1130 Speaker assembly” on page 79 Removal steps of the upper case Release the antenna cable from the cable guides , and then detach the LCD unit from the upper case in the direction shown by arrow When installing: Ensure that the upper case is attached firmly to the LCD unit.
1190 LCD panel For access, remove these FRUs in order: • “1010 Optical disk drive/Removable battery” on page 66 • “1020 Base cover assembly” on page 68 • “1040 Battery pack” on page 70 • “1100 DC-in cable” on page 75 •...
Removal steps of the hinges Remove two hinge mylar tapes Remove six screws , and then remove two hinges Step Screw (quantity) Color Torque M2.5 × 3mm, flat-headed, nylon-coated (6) Black 3.0 +/- 0.3kgf-cm When installing: Ensure that the hinges are attached firmly. 1210 EDP cable and camera module For access, remove these FRUs in order: •...
Page 92
Removal steps of the EDP cable and camera module Release the EDP cable from the cable guide Detach the connector , and then remove the camera from the LCD cover When installing: Ensure that the EDP cable and camera are attached firmly. Hardware Maintenance Manual...
Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead.
User Guide. EU contact: Lenovo, Einsteinova 21, 851 01 Bratislava, Slovakia Trademarks The following terms are trademarks of Lenovo in the United States, other countries or both: Lenovo OneKey Microsoft, Windows, and Windows Server are trademarks of the Microsoft group of companies.
Page 96
Abbreviation Term radio frequency RFID radio-frequency identification ring indicator registered jack SATA Serial Advanced Technology Attachment subscriber identity module supervisor password TFTs thin-film transistors UEFI Unified Extensible Firmware Interface Universal Serial Bus UUID universally unique identifier video graphics array VRAM video random-access memory wide area network Hardware Maintenance Manual...
Need help?
Do you have a question about the V510–14IKB and is the answer not in the manual?
Questions and answers