Table of Contents
Advertisement
Emissions test
RF emissions
CISPR 11
Harmonic
emissions IEC
61000-3-2
Voltage
fluctua
tions/flicker
emissions IEC
61000-3-3
Table 2 Guidance and manufacturer's
declaration – electromagnetic immunity
– for all ME equipment and ME systems
Guidance and manufacturer's declaration –
electromagnetic immunity
The device is intended for use in the
electromagnetic environment specified below. The
customer or the user of the device should assure
that it is used in such an environment.
Immuni
IEC
ty test
60601
test
level
Electro
±6 kV
static
contact
dis
±8 kV air
charge
(ESD)
IEC
61000-
4-2
Electri
±2 kV for
cal fast
power
tran
supply
sient/b
lines
urst IEC
±1 kV for
61000-
input/o
4-4
utput
lines
Surge
±1 kV
IEC
line(s) to
61000-
line(s)
4-5
±2 kV
line(s) to
earth
Voltage
<5% UT
dips,
(>95%
short
dip in
interrup
UT) for
tions
0.5
and
cycle
voltage
varia
40% UT
tions on
power
(60%
supply
dip in UT
input
) for 5
lines IEC
cycles
61000-
4-11
70% UT
(30% dip
in UT )
for 25
cycles
<5% UT
(>95%
dip in UT
) for 5 s
Power
3A/m
fre
quency
(50/60
Hz)
magnet
ic field
IEC
61000-
4-8
Note: UT is the AC electrical voltage prior to
application of the test level.
Table 4 Guidance and manufacturer's
declaration – electromagnetic immunity
–for ME equipment and ME systems that
are not life supporting
Guidance and manufacturer's declaration –
electromagnetic immunity .The device is intended
for use in the electromagnetic environment
specified below. The customer or the user of the
device should assure that it is used in such an
environment.
IMMUNITY
test
Conducted RF
IEC
61000-4-6
Radiated RF
IEC
61000-4-3
Electromagnetic environment - guidance
Portable and mobile RF communications
equipment should be used no closer to any part of
the device, including cables, than the
recommended separation distance calculated from
the equation applicable to the frequency of the
transmitter.
Recommended separation distance:
Ö
d = 1.167
P
Ö
d = 1.167
P 80 MHz to 800MHz
Ö
d = 2.333
P 800 MHz to 2.5 GHz
where P is the maximum output power rating of
the transmitter in watts (W) according to the
transmitter manufacturer and d is the
recommended separation distance in metres (m).
Com
Electromagnetic
pliance
environment -
guidance
Class B
Not
applica
ble
Not
applica
ble
Com
pliance
level
±6 kV
contact
±8 kV
air
±2 kV
for
power
supply
lines
±1 kV
line(s)
to
line(s)
<5% UT
(>95%
dip in
UT) for
0.5
cycle
40% UT
(60%
dip in
UT ) for
5
cycles
70% UT
(30%
dip in
UT ) for
25
cycles
<5% UT
(>95%
dip in
UT ) for
5 s
3A/m
IEC 60601 TEST
LEVEL
3 Vrms
150 kHz to
80 MHz
3 V/m
80 MHz to 2.5
GHz
Electromagnetic
environment -
guidance
Floors should be
wood, concrete or
ceramic tile. If
floors are covered
with synthetic
material, the
relative humidity
should be at least
30%.
Electrical power
quality should be
that of a typical
commercial or
hospital
environment.
Electrical power
quality should be
that of a typical
commercial or
hospital
environment.
Electrical power
quality should be
that of a typical
commercial or
hospital
environment. If the
user of the device
requires continued
operation during
power
interruptions, it is
recommended
that the device be
powered from an
uninterruptible
power supply or a
battery.
Power frequency
magnetic fields
should be at levels
characteristic of a
typical location in
a typical
commercial or
hospital
environment.
Compliance
level
3 Vrms
3 V/m
Advertisement
Table of Contents
