Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for STOVES S1100
Summary of Contents for STOVES S1100
- Page 1 S1100 Professional Cooker Hood User & Installation Instructions...
-
Page 3: Table Of Contents
Contents User’s Section ......... 2 Introduction . -
Page 4: User's Section
Introduction Thank you for buying this high quality Installation hood from Stoves, we hope it makes and This appliance has been designed for attarctive and useful addition to your use as an exhausting (air evacuation kitchen. to the outside) or filtering (indoor air Our policy is one of constant development re-cycling) hood. -
Page 5: Using The Hood
Using the Hood Figure 1 To illuminate the cooking area under- neath the hood, push the light control button in to the “on” position. switch off, press again to return to the “off” position. To operate the hood, press the button for the required speed - select: 1 low, Figure 1: hood controls: medium, or 3 high speed. -
Page 6: Care And Maintenance
Care & Cleaning Before cleaning or maintenance, Outer casing switch off the electricity supply. All external parts of the outer casing can be safely cleaned with a c l e a n Replacing a light bulb cloth wrung out in hot soapy water. 1. - Page 7 Care & Cleaning Carbon filters (models installed for Before cleaning or maintenance, switch off the electricity supply. use with the re-circulation method only) The carbon filters absorb cooking To avoid any fire risk, the following odours and need renewing after about cleaning instructions must be followed: 4 months of normal use.
-
Page 8: Installation
Installation Mounting height Regulations and standards Before you start please read instructions The cooker hood must be fitted at least carefully. All installations, service and 650 mm above a gas or electric hob. repair work must be in accordance If cooker / hob instructions give a with local standards and regulations. -
Page 9: Wall Fixing
Installation Wall fixing (fig 2,3 & 5) 1. Using the screws provided, fit the two wall brackets to the support bracket so that the distance between the outer edges of the 2 wall brackets is the same as the width of the upper link section. 2. - Page 10 Installation Figure 4 Figure 5 900 or 1000mm Please note: Dimensions are nominal Figure 6 and shown here as maximums. Body of hood dimensions: link pieces 900 Professional secure to 900mm x 520mm x 50mm wall brackets with screws in W x D x H connection 1000 Professional flange...
-
Page 11: Method 1: Re-Circulation
Installation Assembly Method 1: Re-circulation (dual filtration) 1. Remove the grease filters. The fan draws cooking fumes through 2. Fit the new carbon filter (if supplied the washable grease filters into the - may be packed separately) b y underside of the hood, then through e n g a g i n g it into the slots below the the carbon filters, to remove odours motor, push in firmly. -
Page 12: Method 2: Extraction Through An Outside Wall
Installation Method 2: Extraction through Wall vent kit and ducting an outside wall • For connecting the hood outlet The fan draws cooking fumes through adaptor to the outside wall, we the washable grease filter into the recommend that a wall vent kit is underside of the hood, then the fumes purchased from your supplier or local hardware store. -
Page 13: Electrical Connection
Installation Electrical connection Figure 7: Typical example of a Typical example of a double double pole fused spur outlet. pole fused spur outlet This appliance is double insulated for safety and therefore does not require an earth connection to the mains inlet. The wires in the mains lead are coloured in accordance with the following code:... -
Page 14: Technical Data
Technical Data Electricity supply 230 - 240V ~ 50Hz Grease filters x 3 aluminium panel Classification Note: class II metal encased After cleaning, grease filters may lose their colour slightly - this does not Noise level (External Venting) affect their performance. Position 4 (booster) 55 dBA Position 3... -
Page 15: Customer Support
Customer Support In case of difficulty please call our Customer Support Helpline on 0844 815 3740 When you dial this number you will hear a ringing tone. This indicates that your call has been accepted and is being held in a queue. Calls are answered in strict rotation as our Customer Support Representatives become available. - Page 16 STONEY LANE, PRESCOT, MERSEYSIDE, L35 2XW 08 27234 01 © 09.2011 3LIK1005...
Need help?
Do you have a question about the S1100 and is the answer not in the manual?
Questions and answers