Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Stentofon AudioCodes MP-114
-
Page 1: Sip Gateway
SIP Gateway AudioCodes MP-114/118 A100K10333 v.5.5 CONFIGURATION GUIDE 2009-02-04... - Page 2 Zenitel Norway AS and its subsidiaries assume no responsibilities for any errors that may appear in this publication, or for damages arising from the information in it. No information in this publication should be regarded as a warranty made by Zenitel Norway AS. The information in this publication may be updated or changed without notice.
-
Page 3: Table Of Contents
2.2.1 Create a SIP Trunk Node ............6 2.2.2 Define the AlphaCom / SIP routing ........7 2.2.3 Create Prefix number ............7 2.2.4 Update the exchange ............7 3 AUDIOCODES MP-114/118 CONFIGURATION .......8 3.1 Configure Network Parameters...........8 3.2 IP Configuration ................9 3.3 SIP Parameters................9 3.4 Audio Codec................9... -
Page 4: General Information
GENERAL INFORMATION 1.1 About this Document This document is a configuration guide describing the setup of the AlphaCom E system and the AudioCodes MP-114/118 SIP Gateway. The document covers the most common features used in an AlphaCom E <-> AudioCodes interconnection. -
Page 5: Alphacom Configuration
Log on to AlphaWeb and enter a valid IP address on the Ethernet port. In the example below, Ethernet port 1 is used. Consult your network administrator to obtain the IP address. A100K10333 v.5.5 Configuration Guide Page 5 AudioCodes MP-114/118... -
Page 6: Insert Sip Trunk Licenses
2.1.2 Insert SIP Trunk licenses Log on to AlphaWeb and install the SIP Trunk license. 2.1.3 Firewall (filter) settings Enable the SIP protocol and VoIP Audio on the desired Ethernet port (default enabled for Ethernet port1). 2.2 AlphaPro Configuration 2.2.1 Create a SIP Trunk Node From the AlphaPro main menu, use the ‘+’... -
Page 7: Define The Alphacom / Sip Routing
2.2.4 Update the exchange Log on to the exchange and update the exchange by pressing the SendAll button. Reset the exchange after the send operation is finished. A100K10333 v.5.5 Configuration Guide Page 7 AudioCodes MP-114/118... -
Page 8: Audiocodes Mp-114/118 Configuration
AUDIOCODES MP-114/118 CONFIGURATION 3.1 Configure Network Parameters The AudioCodes MP-114/118 VoIP Gateway comes with default network parameters (factory default parameters). Before you can set up the gateway in the network, you have to change the default IP address to a fixed IP address in your network environment. -
Page 9: Ip Configuration
Select the voice coder in 'Coders Table' page (Configuration tab > Protocol Configuration menu > Protocol Definition submenu > Coders page item). Choose G.711U-law Coder Name, 20 ms Packetization Time and Silence Suppression Disabled. A100K10333 v.5.5 Configuration Guide Page 9 AudioCodes MP-114/118... -
Page 10: About Saving Changes
Press Submit to save changes 3.5 About Saving Changes The Submit button will save the data to the running volatile memory. The changes take effect on-the-fly. The changes will not survive hardware reset or power off. To permanently save the configuration data, store the data to flash memory by selecting Burn from the Tool Bar. -
Page 11: Fxo Line Select
In this table the four FXO lines are selected by dialing 41 – 44 If there are unused lines, leave all fields for that line blank. Group hunt is not used in this call mode, and the IP to Hunt Routing Table must be empty. A100K10333 v.5.5 Configuration Guide Page 11 AudioCodes MP-114/118... -
Page 12: Telephone Network To Alphacom
3.8 Telephone Network to AlphaCom You can choose between three different ways of handling an incoming call from the telephone line: Selective Dialing Automatic Dialing Delayed Automatic Dialing 3.8.1 Selective Dialing A second dial tone will be presented when calling in, and the user can dial the desired intercom number. -
Page 13: Delayed Automatic Dialing
> Supplementary Services page item. Set ‘Enable Caller ID’ to ‘Enable’ and choose the ‘Caller ID Type’ as used by the PSTN supplier. Check with the local telephone company to find the ‘Caller ID Type’ used. A100K10333 v.5.5 Configuration Guide Page 13 AudioCodes MP-114/118... -
Page 14: Far End Disconnect (Fed)
4.1 Call Termination options in the SIP Gateway The following methods for call termination are supported by the AudioCodes MP-114/118. Note that the used disconnection methods must be supported by the CO (Central Office) or to PBX (Private Branch Exchange). - Page 15 Reset the SIP Gateway for the changes to take effect For more detailed information regarding Call Progress Tones please refer to the AudioCodes User's Manual found on the CD supplied with the unit. A100K10333 v.5.5 Configuration Guide Page 15 AudioCodes MP-114/118...
-
Page 16: Detection Of Silence
4.1.3 Detection of Silence The call is disconnected after silence is detected on both call directions for a specific (configurable) amount of time. This method should only be used as a backup. Display the Navigation Tree in Full View. Enable the relevant detection method in Configuration tab >... -
Page 17: Message Log
Message Log again; the page is cleared and new messages begin appearing. To stop the Message Log, take this step: Close the page by accessing any another page in the Web interface. A100K10333 v.5.5 Configuration Guide Page 17 AudioCodes MP-114/118... -
Page 18: Miscellaneous Features
MISCELLANEOUS FEATURES 6.1 Incoming Calls in Private Incoming calls from the telephone line can be forced to be in private ringing mode, independent of the private/open switch of the intercom station. Check the flag Incoming calls from SIP in private ringing mode in AlphaPro, (Exchange &... -
Page 19: M-Key Control From Telephone Network
Some of the SIP Gateway parameters are configurable through the ini configuration file only (and not via the Web). The CountryCoefficients parameter that determines the line characteristics must be configured via the ini configuration file. Procedure to modify the ini file: A100K10333 v.5.5 Configuration Guide Page 19 AudioCodes MP-114/118... -
Page 20: Country Codes
Get the ini file from the gateway using the Embedded Web Server. From the Tool Bar select Device Actions -> Save Configuration File. Select Save INI File to save the configuration to the PC: Open the file (e.g. in Notepad) and add anywhere in the file the line CountryCoefficients = xx where xx is the country code found below;... -
Page 21: Feature Guide
I 71 I 0 P 40002500 Search List A telephone number can be included in the Search List of a station. Format: I <prefix> P <phone number> Example: I 0 P 40002500 A100K10333 v.5.5 Configuration Guide Page 21 AudioCodes MP-114/118... - Page 22 DOC NO support@stentofon.com A100K10333 v.5.5 STENTOFON products are developed and marketed by Zenitel Norway AS. The company’s Quality Assurance System is certified to meet the requirements in NS-EN ISO 9001:2002. ZENITEL NORWAY AS reserves the Page 22 Configuration Guide A100K10333 v.5.5 right to modify designs and alter specifications without prior notice, in pursuance of a policy of continuous improvement.
Need help?
Do you have a question about the AudioCodes MP-114 and is the answer not in the manual?
Questions and answers