Page 2
KRF-V5200D ACCESSORIES / CAUTIONS Accessories FM indoor antenna (1) AM loop antenna (1) Remote control unit (1) Batteries (R03) (2) (T90-0877-05) (T90-0893-05) RC-R0517 (–) (A70-1719-05) Cautions Information on Disposal of Old Electrical Resetting the Microcomputer and Electronic Equipment (applicable for EU...
KRF-V5200D CIRCUIT DESCRIPTION ● Fan Motor Control Fan control signal from the microprocessor IC601 (X08) When thermal sensor works, the microprocessor will send is supplied to the base of the transistor Q502 if changes the signal to Q502 and Q502 is turn-on. The base of Q503 thermal level.
Page 5
KRF-V5200D CIRCUIT DESCRIPTION Pin No. Pin Name Description ROUT1 R-ch analog output port from internal DAC1 L-ch analog input port R-ch analog input port PVDD Power supply for PLL (4.5 to 5.5V) External resistor port PVSS PLL ground No use (receiver channel 4) SLAVE Slave mode port.
Page 6
KRF-V5200D CIRCUIT DESCRIPTION Pin No. Pin Name Description CMPREQ PCM audio input sampling rate clock CLKIN Master clock input port CLKSEL DSP clock selector FILT2 External fi lter for PLL FILT1 External fi lter for PLL Power supply for clock generator (+2.5V)
Page 7
KRF-V5200D CIRCUIT DESCRIPTION ● Microprocessor: MN101C49KDF (IC601: X08) Port Description Pin No. Pin Name Description Logic VREF- A/D converter -ve power supply. TH_DET D1 Thermal sensor protection detection 1 DET_F Signal level protection detection, front. DET_S Signal level protection detection, surround.
Page 8
KRF-V5200D CIRCUIT DESCRIPTION Pin No. Pin Name Description Logic DSP/CODEC_SCDIN DSP IC data input DSP/CODEC_SCDOUT DSP IC data output DSP/CODEC_SCCLK DSP IC clock No use C/SW_RLY CENTER/SUBWOOFER relay SL/SR_RLY SURROUND relay SBL/SBR RLY BACK SURROUND relay F.AUX_KEY AV AUX key input...
Page 9
KRF-V5200D CIRCUIT DESCRIPTION Pin No. Pin Name Description Logic STANDBY_LED STANDBY led ENC_A1 SELECTOR ENC input A ENC_A2 SELECTOR ENC input B ENC_B1 MULTI CONTROL ENC input A ENC_B2 MULTI CONTROL ENC input B LED 2 (EQ) ACTIVE EQ led...
Page 23
UDZS2.4B high impedance type voltmeter with no signal input. The D851,861 UDZS3.3B measurement value may vary depending on the measuring RECORDING LINE instruments used or on the product. SIGNAL LINE GND LINE B LINE B LINE KRF-V5200D (1/3) X08-3482-70 (6/6)
Page 25
1/4W R503 22.7V +11.9V KRF-V5200D (2/3) The DC voltage is an actual reading measured with a high impedance type voltmeter with no signal input. The measurement value may vary depending on the measuring instruments used or on the product. X09-7032-70 (2/2)
Page 28
. T h e measurement value may vary depending on C706 0.01 R704 the measuring instruments used or on the C707 product. 470u10 KRF-V5200D (3/3) X14-805x-xx (3/3)
KRF-V5200D PARTS LIST HOW TO READ THE PARTS LIST ABBREVIATION OF MODEL AND MASS PRODUCTION’S DESTINATIONS Australia Europe MODEL ABB. KRF-V5200D KRF-V5200D-S...
................D: 343 mm (13-1/2") Weight (net) ..............8.1 kg (17.9 lb) Notes: 1. Kenwood follows a policy of continuous advancements in development. For this reason specifications may be changed without notice. 2. The full perfor mance may not be exhibited in an extremely cold location (under a water-freezing temperature).
Need help?
Do you have a question about the KRF-V5200D and is the answer not in the manual?
Questions and answers