Texas Instruments SimpleLink CC2620 Technical Reference Manual page 242

MCU Event Fabric
Event Number Event Enumeration
0x13 GPT1B
0x14 DMA_CH0_DONE
0x15 FLASH
0x16 DMA_CH18_DONE
0x17 NOT_USED
0x18 WDT_IRQ
0x19 RFC_CMD_ACK
0x1A RFC_HW_COMB
0x1B RFC_CPE_0
0x1C AUX_SWEV0
0x1D AUX_SWEV1
0x1E RFC_CPE_1
0x1F NOT_USED
0x20 NOT_USED
0x21 NOT_USED
0x22 SSI0_COMB
0x23 SSI1_COMB
0x24 UART0_COMB
0x25
0x26 DMA_ERR
0x27 DMA_DONE_COMB
0x28 SSI0_RX_DMABREQ
0x29 SSI0_RX_DMASREQ
0x2A SSI0_TX_DMABREQ
0x2B SSI0_TX_DMASREQ
0x2C SSI1_RX_DMABREQ
0x2D SSI1_RX_DMASREQ
0x2E SSI1_TX_DMABREQ
0x2F SSI1_TX_DMASREQ
0x30 UART0_RX_DMABREQ
0x31 UART0_RX_DMASREQ
0x32 UART0_TX_DMABREQ
0x33 UART0_TX_DMASREQ
0x34 to 0x37 NOT_USED
242 Interrupts and Events
Table 4-6. MCU Event Fabric Input Events (continued)
Description
GPT1B interrupt event, controlled by GPT1:TBMR.*
DMA done for software-triggered UDMA channel 0, see
UDMA0:SOFTREQ.*
FLASH controller error event, the status flags are
FLASH:FEDACSTAT.FSM_DONE and FLASH:FEDACSTAT.RVF_INT
DMA done for software-triggered UDMA channel 18, see
UDMA0:SOFTREQ.*
Watchdog interrupt event, controlled by WDT:CTL.INTEN
RFC Doorbell Command Acknowledgment interrupt, equivalent to
RFC_DBELL:RFACKIFG.ACKFLAG.
Combined RCF hardware interrupt, corresponding flag is here
RFC_DBELL:RFHWIFG.*
Combined interrupt for CPE-generated events. Corresponding flags are
here RFC_DBELL:RFCPEIFG.*. Only interrupts selected with CPE0 in
RFC_DBELL:RFCPEIFG.* can trigger a RFC_CPE_0 event.
AUX software event 0, triggered by AUX_EVCTL:SWEVSET.SWEV0,
also available as AUX_EVENT0 AON wake-up event.
MCU domain wake-up control AON_EVENT:MCUWUSEL.*
AUX domain wake-up control AON_EVENT:AUXWUSEL.*
AUX software event 1, triggered by AUX_EVCTL:SWEVSET.SWEV1,
also available as AUX_EVENT2 AON wake-up event.
MCU domain wake-up control AON_EVENT:MCUWUSEL.*
AUX domain wake-up control AON_EVENT:AUXWUSEL.*
Combined interrupt for CPE-generated events. Corresponding flags are
here RFC_DBELL:RFCPEIFG.*. Only interrupts selected with CPE1 in
RFC_DBELL:RFCPEIFG.* can trigger a RFC_CPE_1 event.
SSI0 combined interrupt, interrupt flags are found here SSI0:MIS.*.
SSI0 combined interrupt, interrupt flags are found here SSI1:MIS.*.
UART0 combined interrupt, interrupt flags are found here UART0:MIS.*.
DMA bus error, corresponds to UDMA0:ERROR.STATUS
Combined DMA done corresponding flags are here
UDMA0:REQDONE.*
SSI0 RX DMA burst request, controlled by SSI0:DMACR.RXDMAE
SSI0 RX DMA single request, controlled by SSI0:DMACR.RXDMAE
SSI0 TX DMA burst request, controlled by SSI0:DMACR.TXDMAE
SSI0 TX DMA single request, controlled by SSI0:DMACR.TXDMAE
SSI1 RX DMA burst request, controlled by SSI0:DMACR.RXDMAE
SSI1 RX DMA single request, controlled by SSI0:DMACR.RXDMAE
SSI1 TX DMA burst request, controlled by SSI0:DMACR.TXDMAE
SSI1 TX DMA single request, controlled by SSI0:DMACR.TXDMAE
UART0 RX DMA burst request, controlled by
UART0:DMACTL.RXDMAE
UART0 RX DMA single request, controlled by
UART0:DMACTL.RXDMAE
UART0 TX DMA burst request, controlled by UART0:DMACTL.TXDMAE
UART0 TX DMA single request, controlled by
UART0:DMACTL.TXDMAE
Always 0
Copyright © 2015, Texas Instruments Incorporated
SWCU117C – February 2015 – Revised September 2015
Submit Documentation Feedback
www.ti.com