Page 1
Home Network System Window/Door Sensor KX-HNS101E Model No. Thank you for purchasing a Panasonic product. This document explains how to install the window/door sensor properly. For details about how to use the system, refer to the User’s Guide (page 19).
Table of Contents Introduction Accessory information ....3 General information ....4 Important Information About this system ......5 For your safety ......5 Important safety instructions ..6 For best performance ....6 Other information .......7 Setup Part names and functions ..9 LED indicator ......9 Setup overview ......9 Inserting the battery ....10 Registering the window/door...
Sales and support information Customer Communications Centre R For customers within the U.K.: 0330 3331112 R For customers within Ireland: 01 4475228 R For further support on your product, please visit our website: www.panasonic.co.uk Helpline Tel. No.: U.K. 0330 3331112 Ireland 01 4475228...
Introduction Direct Sales at Panasonic U.K. R Order accessory and consumable items for your product with ease and confidence by phoning our Customer Communications Centre Monday - Friday 9:00am - 5:00pm (Excluding public holidays). R Go on line through our Internet Accessory ordering application at www.pas-europe.com...
R Keep small parts (magnet unit, protection from property loss. magnet unit cover, screws, etc.) out Panasonic will not be held of the reach of children. There is a responsible in the event that risk of swallowing. In the event they...
Hub location/avoiding noise swallowing. If the battery is The hub and other compatible swallowed, seek medical attention Panasonic devices use radio waves to immediately. communicate with each other. R Remove the battery if it becomes R For maximum coverage and unusable.
Important Information – away from electronic appliances Dispose of used batteries according to such as TVs, radios, personal the instructions. computers, wireless devices, or other phones. Routine care – facing away from radio frequency R Wipe the outer surface of the transmitters, such as external product with a soft moist cloth.
Page 8
Important Information Note for the battery symbol This symbol (B) might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved. Note for the battery removal procedure Refer to “Inserting the battery”...
Setup Part names and LED indicator functions You can press M N and check the LED indicator to confirm the sensor’s n Sensor unit n Magnet unit status. Indicator Status Green, lit Window/door is closed Red, lit Window/door is open Red, Sensor is out of range blinking...
Setup desired installation area is suitable Insert the battery. to proper operation. Temporary placement Temporarily place the window/ door sensor in the desired location and confirm that it operates properly (page 13). Installation Install the window/door sensor on the same position where proper operation was confirmed (page 16).
Setup devices and group them by location. For more information, refer to the Registering the User’s Guide (page 19). window/door sensor This procedure is not required for Changing the sensor devices that were included as part of type a bundle. Before you can use the window/door You can select whether a window/door sensor, it must be registered to the hub.
Setup Wireless communication range The wireless communication range of each device in the system from the hub is approximately 50 m indoors and approximately 300 m outdoors. Wireless communication may be unreliable when the following obstacles are located between the hub and other devices.
Setup Temporary placement Before installing the window/door sensor, temporarily place it in the desired location and confirm that it operates properly by pressing M Important: R Attach the sensor unit to the window frame or door frame, and attach the magnet unit to the window or door.
Page 14
Setup Example 1: Installed on the left side of a window Correct Green “ ” marks point directly at each other and are within 25.4 mm of each other. Result: When you press M N (A), the LED indicator lights in green (B). Incorrect “...
Page 15
Setup Example 2: Installed on the right side of a window Correct Green “ ” marks point directly at each other and are within 25.4 mm of each other. Result: When you press M N (A), the LED indicator lights in green (B). Incorrect “...
Setup Installation Install the window/door sensor in the same position where proper operation was confirmed (page 13). You can install the window/door sensor using screws or double-sided tape, depending on your preference or the material of the installation area. Note: R When installing, make sure the battery is inserted properly and the sensor unit cover is completely closed.
Page 17
Setup Sensor unit: Attach the sensor unit. Screws 86.2 mm Magnet unit: Attach the magnet unit. Screws 24.4 mm Attach the covers. Important: Align the “ ” marks on the sensor unit and the magnet unit so that they point directly at each other and are no more than 25.4 mm apart. Helpline Tel.
Page 18
Setup Securing with double-sided tape Note: R Make sure the surfaces of the sensor unit, magnet unit, and the installation area are clean and dry before applying double-sided tape. Check that the sensor unit cover and magnet unit cover are attached. Affix double-sided tape to the sensor unit and magnet unit.
You can use the app to arm and disarm the alarm system, confirm the current status of the sensor, and view a log of previous events. – Sensor integration www.panasonic.net/pcc/support/tel/ homenetwork/manual/ Helpline Tel. No.: U.K. 0330 3331112 Ireland 01 4475228...
Appendix Specifications R Standards DECT (Digital Enhanced Cordless Telecommunications) R Frequency range DECT: 1.88 GHz – 1.90 GHz R RF transmission power Approx. 10 mW (average power per channel) R Power source Lithium battery CR2 (1 ´ 3.0 V, 850 mAh) R Operating conditions -10 °C –...
The guarantee period applicable to this product shall be 12 months. Please keep these operating instructions with your receipt. Panasonic U.K. a branch of Panasonic Marketing Europe GmbH Receipt No. Date of purchase Model No.