Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Spa Electrics WN950
Summary of Contents for Spa Electrics WN950
- Page 1 6” LED NICHE LIGHT INSTALLATION & OWNER’S MANUAL...
-
Page 2: Table Of Contents
CONTENTS READ THIS FIRST TOOLS REQUIRED PRODUCT SUPPORT AND INFORMATION INCLUDED PARTS INSTALLATION INSTRUCTIONS (STEPS 1 - 11) MULTI PLUS - MANUAL OPERATION MULTI-PLUS SETUP AVAILABLE COLOUR MODES WIRING DIAGRAM KEY DIMENSIONS ELECTRICAL GROUNDING & FCC STATEMENT NOTICE FRESH WATER USE ONLY HORIZONTAL MOUNT ONLY NOT INTENDED FOR OPERATION OUT OF WATER FOR SUPPLY CONNECTION, USE ONLY AN ISOLATING LOW VOLTAGE POWER... -
Page 3: Read This First
• Maximum installation depth for the ParaGlo 6” Light (WN950) is 1M (40”) below nominal water level (to top of light) • The ParaGlo 6“ Light (WN950) Must be correctly installed in or on the wall of the pool with the top of the lens no less than 4” below the nominal water level. -
Page 4: Tools Required
TOOLS REQUIRED • No. 2 Phillips screwdriver IMPORTANT NOTE •The use of power tools during installation is not recommended as these devices can cause damage to the light and components. •All installation steps should be carried out with manual tools only. •The enclosed images are for illustrative purposes only. -
Page 5: Included Parts
UL LISTED 12V AC CLASS 2 POWER SUPPLY OR POWER SOURCE INTENDED FOR SWIMMING POOL USE. Minimum power source wattage requirement - 15 Watts per light Spa Electrics recommends “INTERMATIC PX” safety transformers for use with Quantum & Atom Lights... -
Page 6: Installation Instructions (Steps 1 - 11)
INSTALLATION ATTACH NICHE TO REINFORCEMENT BARS (Before spraying concrete) Attach the niche to either horizontal or vertical steel mounting bars using wire ties or similar. Ensure conduit entry is at the top of the niche. (Fig. 1) CAUTION: The ParaGlo 6” light must be correctly installed in the wall of the pool with the top of the lens no less than 4”... - Page 7 NOTE: Conduit should contain a draw wire to allow for easy installation of power cable. ELECTRICAL GROUNDING The ParaGlo 6” (WN950) luminaire POWER SUPPLY with its plastic housing design and (TRANSFORMER) plastic niche does not require grounding / bonding when operated within a Class 2 circuit supply.
- Page 8 CONCRETE SPRAYING Spray concrete, paying particular attention to covering the entire niche. Using fingers, scoop out the concrete around the front edge of the niche. (Fig 3) WARNING: Ensure that the concrete is well compacted around the rear and base of the niche, otherwise the pool may leak.
- Page 9 MOUNTING RING PREPARATION Apply PVC solvent cement to bubble at rear of the mounting ring, and also to the inside of the niche where the mounting ring is likely to finish. (Approximately 1 ½” inside niche) (Fig. WARNING: Ensure PVC solvent cement is suitable for ABS plastics. TOP MARKER APPLY PVC SOLVENT CEMENT APPLY SEALANT...
- Page 10 APPLY POOL FINISH Plaster or tile interior pool surface, level with raised edge of mounting ring. CAUTION: Interior surface should not finish more than ½” higher than raised edge of mounting ring, or the light may not be able to be mounted. MOUNTING RING RAISED EDGE PLUG TOP WITH TERMINAL COVER...
- Page 11 10 10 CABLE ATTACHMENT Remove the terminal covers from both the light housing and the plugtop. Ensure both plug top seals are present and located within their grooves. Attach plug top to light housing using the three fixing screws provided and tighten firmly by hand, using phillips-head screwdriver.
-
Page 12: Multi Plus - Manual Operation
MANUAL MODE USER INSTRUCTIONS OPERATING INSTRUCTIONS 1. To change the color of the light, simply turn your light OFF for 2 seconds and then turn it back ON. This will signal the light to proceed to the next colour in the sequence. Refer to pg. - Page 13 MULTI PLUS SETUP cont. STEP 2 - LIGHT SETUP IMPORTANT: Ensure Lights have been off for 30 seconds prior to performing this step. NOTE: This step can either be performed via a wall switch OR via the controller panel/Mobile App. TURN LIGHTS TURN LIGHTS REPEAT...
- Page 14 STEP 3 (continued) - SELECTING OPERATING MODE ‘FLASHING’ COLOUR CONTROLLER / OPERATING TYPE LIGHT MODEL SELECTED* 1. RED Manual Mode (wall switch) 2. GREEN Spa Electrics iRIS Controller 3. MAGENTA Astral Connect 10 SLX Light (2016 to current) 4. WHITE Jandy Aqualink RS Intellibrite Light (F/W Rev.
-
Page 15: Available Colour Modes
OPERATING MODE COLOURS MANUAL MODE iRIS MODE CONNECT 10 MODE WHITE 4000K WHITE 4000K BLUE AQUA AQUA MAGENTA BLUE BLUE MAGENTA MAGENTA ORANGE GREEN LIME LIME AQUA GREEN GREEN WHITE OCEANIC VIEWS OCEANIC VIEWS CUSTOMISED COLOUR TRANSCENDENCE TRANSCENDENCE RAINBOW PATTERN OUTBACK AUSTRALIA OUTBACK AUSTRALIA OCEAN PATTERN... -
Page 16: Wiring Diagram
INSTALLATION DIAGRAM CONTROLLER EASYTOUCH PENTAIR INTELLITOUCH PENTAIR ® RS ONETOUCH AQUALINK (REV R - CURRENT) ® AQUALINK ® OMNILOGIC HAYWARD TRANSFORMER Paramount Pool systems recommends the use of the “INTERMATIC PX” safety transformers with the ParaGlo 3” & 6” lights PARAGLO 6”... -
Page 17: Key Dimensions
KEY DIMENSIONS 188mm / 7.4” FRONT VIEW 17mm / 0.66” 142mm / 5.6” 17mm / 0.66” RIGHT SIDE VIEW... -
Page 18: Electrical Grounding & Fcc Statement
Pentair Water Pool and Spa, Inc and/or its affiliated companies in the United states or other countries. Colorlogic is a registered trademark of Hayward Industries Inc. and/or its affiliated companies in the United states or other countries. Spa Electrics Export Pty Ltd Australia and it’s brands are not affiliated or endorsed by these companies and/or their brands. - Page 20 NOTE PLEASE STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE Proudly manufactured by Spa Electrics www.spaelectrics.com.au COPYRIGHT 2017 SPA ELECTRICS PTY. LTD. ALL RIGHTS RESERVED 004-027-8706-00 REV(20170531)
Need help?
Do you have a question about the WN950 and is the answer not in the manual?
Questions and answers